ISL29008

® ISL29006, ISL29007, ISL29008 Data Sheet September 21, 2010 FN6282.1 Small, Low Power, Current-Output Ambient Light Photo Detect IC The ISL29006, ISL29007, and ISL29008 are light-to-current silicon optical sensors combining a photodiode array and a current amplifier on a single monolithic IC. The photodiode’s spectral sensitivity approximates the human eye response peaking at 550nm with virtually no infrared (IR) response. Exposed to light, these light sensors give current outputs that are linearly proportional to the light intensity. The output of ISL29006 is configured as a current source, and the output of ISL29007 is configured as a current sink. Both ISL29006 and ISL29007 offer an EN pin that can be used for a polling scheme to extend the battery life of portable devices. The ISL29008 has dual outputs simultaneously sinking and sourcing current. With output currents at opposite polarity, it can simultaneously control two light sources/drivers that have incongruent illumination requirement depending on ambient light conditions. For example, at bright ambient light levels, display backpanels need more intensity while the keyboard illumination needs to be dimmer, whereas at darker ambient light levels, display backpanels need less intensity while the keyboard illumination needs to be brighter. By connecting an external resistor from ISRC to GND or from ISNK to VDD, the current output can be converted into voltage output. Housed in an ultra-compact 2mmx2.1mm ODFN clear plastic package, this device is excellent for power saving control function in cell phones, PDAs and other handheld applications. Features • 0.5 lux to 10,000 lux range • 1.8V to 3.6V supply range • Low supply current (3.5µA @ 100 lux) • Fast response time • Close to human eye response • IR Rejection • Internal dark current compensation • Lux to current source or/and sink • Excellent output linearity of luminance • 6 Ld ODFN: 2mmx2.1mmx0.7mm • Pb-free (RoHS compliant) Applications • Display and keypad dimming for: - Mobile devices: smart phone, PDA, GPS - Computing devices: notebook PC, webpod - Consumer devices: LCD-TV, digital picture frame, digital camera • Industrial and medical light sensing Ordering Information PART NUMBER (Note) ISL29006IROZ-T7* ISL29007IROZ-T7* ISL29008IROZ-T7* ISL29006IROZ-EVALZ ISL29007IROZ-EVALZ ISL29008IROZ-EVALZ TEMP. RANGE (°C) -40 to +85 -40 to +85 -40 to +85 PACKAGE (Pb-free) 6 Ld ODFN 6 Ld ODFN 6 Ld ODFN PKG. DWG. # L6.2x2.1 L6.2x2.1 L6.2x2.1 Evaluation Board Evaluation Board Evaluation Board *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008, 2010. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL29006, ISL29007, ISL29008 Pinouts ISL29006 (6 LD ODFN) TOP VIEW ISL29007 (6 LD ODFN) TOP VIEW ISL29008 (6 LD ODFN) TOP VIEW VDD 1 GND 2 NC 3 THERMAL PAD* 6 ISRC 5 NC 4 EN VDD 1 GND 2 NC 3 THERMAL PAD* 6 EN 5 NC 4 ISNK VDD 1 GND 2 NC 3 THERMAL PAD* 6 ISRC 5 NC 4 ISNK Pin Descriptions ISL29006 PIN NUMBER 1 2 3, 5 4 6 4 ISL29007 PIN NUMBER 1 2 3, 5 6 6 4 ISL29008 PIN NUMBER 1 2 3, 5 NAME VDD GND NC EN ISRC ISNK DESCRIPTION Supply, 1.8V to 3.6V Ground No connect Active LOW enable Current source out Current sink out Simplified Block Diagrams VDD 1 VDD 1 EN 6 ISRC 6 ISNK 4 LIGHT DATA PROCESS CURRENT AMPLIFIER OUTPUT CURRENT α LIGHT INTENSITY LIGHT DATA PROCESS CURRENT AMPLIFIER OUTPUT CURRENT α LIGHT INTENSITY GND 2 PHOTODIODE ARRAY EN 4 GND 2 PHOTODIODE ARRAY ISL29006 ISL29007 VDD 1 LIGHT DATA PROCESS CURRENT AMPLIFIER OUTPUT CURRENT α LIGHT INTENSITY 6 ISRC 4 ISNK GND 2 PHOTODIODE ARRAY ISL29008 2 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Absolute Maximum Ratings (TA = +25°C) Supply Voltage between VDD and GND . . . . . . . . . . . . . . . . . . 3.6V Pin Voltage (ISRC, ISNK and EN) . . . . . . . . . . . . . . . -0.2V to 3.6V Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . 6mA Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C ESD Voltage Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V Thermal Information Thermal Resistance θJA (°C/W) 6 Ld ODFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +90°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-45°C to +100°C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-45°C to +85°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER E VDD IDD VDD = 3V, TA = +25°C, RL = 100kΩ, green LED light, unless otherwise specified. DESCRIPTION CONDITION MIN TYP 0.5 to 10k 1.8 E = 1000 lux E = 100 lux E = 0 lux 27 3.5 250 1.65 1.65 11.5 11.5 0.9 16.45 16.45 1.00 0.22 20 350 IS29006 andISL29008 E = 1000 lux ISL29007 and ISL29008 E = 1000 lux RL = 100kΩ, E = 300 lux from 0 Lux RL = 100kΩ, E = 1000 lux from 0 Lux VDD - 0.2 0.2 104 27 562 233 504 209 21.3 21.3 1.1 2.5 3.3 35 MAX UNIT lux V µA µA nA µA µA µA µA µA µA % nA V V µs µs µs µs µs µs Range of Input Light Intensity Power Supply Range Supply Current ISRC1 ISNK1 ISRC2 ISNK2 ISNK/ISRC IDARK ΔIOUT ISD VO-MAX1 VO-MAX2 tR Light-to-Current Sourcing Accuracy Light-to-Current Sinking Accuracy Light-to-Current Sourcing Accuracy Light-to-Current Sinking Accuracy Mismatch between ISNK and ISRC Dark Current Output in the Absence of Light Output Current Variation Over Three Light Sources: Fluorescent, Incandescent and Halogen Supply Current when Shut Down ISRC Max Output Compliance Voltage at 95% of Nominal Output ISNK Min Output Compliance Voltage at 95% of Norminal Output ISRC and ISNK Rise Time (Note 1) IS29006 and ISL29008 E = 100 lux ISL29007 and ISL29008 E = 100 lux ISL29006 and ISL29008 E = 1000 lux ISL29007 and ISL29008 E = 1000 lux E = 1000 lux for ISL29008 E = 0 lux, RL = 10MΩ E = 1000 lux tF ISRC and ISNK Fall Time (Note 1) RL = 100kΩ, E = 300 lux to 0 Lux RL = 100kΩ, E = 1000 lux to 0 Lux tD ISRC and ISNK Delay Time for Rising Edge (Note 1) RL = 100kΩ, E = 300 lux from 0 Lux RL = 100kΩ, E = 1000 lux from 0 Lux 3 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Electrical Specifications PARAMETER tS VDD = 3V, TA = +25°C, RL = 100kΩ, green LED light, unless otherwise specified. (Continued) DESCRIPTION ISRC and ISNK Delay Time for Falling Edge (Note 1) CONDITION RL = 100kΩ, E = 300 lux to 0 Lux RL = 100kΩ, E = 1000 lux to 0 Lux VLO VHI ILO IHI tEN tDIS NOTE: 1. Switching time measurement is based on Figures 1 and 2. Maximum Voltage at EN pin to Enable Minimum Voltage at EN pin to Disable Input Current at EN pin Input Current at EN pin Enable Time Disable Time V EN = 0V V EN = 3V RL = 100kΩ, E = 100 lux RL = 100kΩ, E = 100 lux MIN TYP 30 18 0.5 VDD - 0.5 1 1 19 202 MAX UNIT µs µs V V nA nA µs µs POWER SUPPLY OR SOURCE METER VCC INPUT LIGHT 10% FUNCTION GENERATOR ISL29006 RL OUTPUT VOUT 90% tr tS 90% 10% tf% tD FIGURE 1. TEST CIRCUIT FOR RISE/FALL TIME MEASUREMENT FIGURE 2. TIMING DIAGRAM Typical Performance Curves 1.2 NORMALIZED RESPONSE 1.0 0.8 0.6 0.4 0.2 0.0 -0.2 LIGHT SENSOR RESPONSE NORMALIZED LIGHT INTENSITY HUMAN EYE RESPONSE 1.2 FLUORESCENT 1.0 0.8 0.6 0.4 WLED 0.2 0 300 INCANDESCENT SUN HALOGEN 300 400 600 800 WAVELENGTH (nm) 1.0k 1.1k 400 500 600 700 800 WAVELENGTH (nm) 900 1000 1100 FIGURE 3. SPECTRAL RESPONSE FIGURE 4. SPECTRUM OF LIGHT SOURCES 4 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Typical Performance Curves (Continued) RADIATION PATTERN 20° LUMINOSITY 30° ANGLE 40° 50° 60° 70° 80° 90° 0.2 0.4 0.6 0.8 RELATIVE SENSITIVITY 20° 30° 40° 50° 60° 70° 80° 90° 1.0 OUTPUT CURRENT (µA) 10° 0° 10° 400 380 VDD = 3V 360 340 FLUORESCENT LIGHT 320 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 20000 LIGHT INTENSITY (LUX) FIGURE 5. RADIATION PATTERN FIGURE 6. OUTPUT CURRENT vs LIGHT INTENSITY 200 180 OUTPUT CURRENT (µA) 160 140 120 100 80 60 40 20 0 0 FLUORESCENT INCANDESCENT HALOGEN OUTPUT CURRENT (µA) 20 18 16 14 12 10 8 6 4 2 HALOGEN INCANDESCENT FLUORESCENT FLUORESCENT INCANDESCENT HALOGEN HALOGEN INCANDESCENT FLUORESCENT 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 LIGHT INTENSITY (LUX) 0 0 100 200 300 400 500 600 700 800 900 1000 LIGHT INTENSITY (LUX) FIGURE 7. OUTPUT CURRENT vs LIGHT INTENSITY FIGURE 8. OUTPUT CURRENT vs LIGHT INTENSITY SOURCE CURRENT/SINK CURRENT 2.0 1.8 OUTPUT CURRENT (µA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 FLUORESCENT INCANDESCENT HALOGEN 1.000 0.995 0.990 0.985 0.980 0.975 0.970 0.965 VDD = 3V FLUORESCENT FLUORESCENT HALOGEN INCANDESCENT 10 20 30 40 50 60 70 LIGHT INTENSITY (LUX) 80 90 100 10 100 1000 10000 100000 LIGHT INTENSITY (LUX) FIGURE 9. OUTPUT CURRENT vs LIGHT INTENSITY FIGURE 10. RATIO OF SOURCE CURRENT AND SINK CURRENT vs LIGHT INTENSITY 5 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Typical Performance Curves (Continued) OUTPUT SOURCE CURRENT (nA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -0.2 VDD = 3V REXT = 10MΩ LIGHT INTENSITY = 0 LUX 0.104 0.091 0.078 0.065 0.052 0.039 0.026 0.013 0 -0.013 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (°C) EQUIVALENT LIGHT INTENSITY (LUX) 1000 1.8 0.117 TRANSIENT TIME (ms) 100 FALL TIME DELAY TIME BEFORE RISING 10 1 0.1 DELAY TIME BEFORE FALLING RISE TIME 1000 0.01 1 10 100 LUX CHANGE FROM/TO 0 LUX (LUX) FIGURE 11. TRANSIENT TME vs LUX CHANGE FROM/TO 0 LUX FIGURE 12. OUTPUT CURRENT vs TEMPERATURE AT 0 LUX 0.20 NORMALIZED OUTPUT CURRENT VDD = 3V 0.19 REXT = 10MΩ 0.18 LIGHT INTENSITY = 0 LUX 0.17 0.16 0.15 0.14 0.13 0.12 0.11 0.10 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 1.05 VDD = 3V 1.04 FLUORESCENT LIGHT 1.03 1.02 1.01 1.00 0.99 0.98 LINEAR (1000 LUX) 1000 LUX 300 LUX LINEAR (300 LUX) SUPPLY CURRENT (µA) 0.97 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (°C) TEMPERATURE (°C) FIGURE 13. SUPPLY CURRENT vs TEMPERATURE AT 0 LUX FIGURE 14. NORMALIZED OUTPUT CURRENT vs TEMPERATURE 20 NORMALIZED OUTPUT CURRENT 18 SUPPLY CURRENT (µA) 16 14 12 10 8 6 4 ISL29006 2 VDD = 3V FLUORESCENT LIGHT 0 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE (°C) 300 LUX 1100 LUX 1.02 FLUORESCENT LIGHT INTENSITY = 850 LUX 1.01 1.00 0.99 0.98 0.97 1.5 2.0 2.5 3.0 3.5 4.0 SUPPLY VOLTAGE (V) FIGURE 15. SUPPLY CURRENT vs TEMPERATURE FIGURE 16. NORMALIZED OUTPUT CURRENT vs SUPPLY VOLTAGE 6 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Typical Performance Curves (Continued) 20.0 19.8 SUPPLY CURRENT (µA) 19.6 19.4 19.2 19.0 18.8 18.6 18.4 18.2 18.0 1.5 0V 2.0 2.5 3.0 SUPPLY VOLTAGE (V) 3.5 4.0 VOUT VDD = 3V, REXT = 100kΩ LIGHT INTENSITY RISES FROM 0 TO 300 LUX AND FALLS FROM 300 TO 0 LUX WITH WHITE LED FLUORESCENT LIGHT INTENSITY = 850 LUX LIGHT INTENSITY FIGURE 17. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 18. TRANSIENT RESPONSE OF ISL29006 TO CHANGE IN LIGHT INTENSITY LIGHT INTENSITY VDD = 3V, REXT = 100kΩ LIGHT INTENSITY RISES FROM 0 TO 300 LUX AND FALLS FROM 300 TO 0 LUX WITH WHITE LED VOUT 3V FIGURE 19. TRANSIENT RESPONSE OF ISL29007 TO CHANGE IN LIGHT INTENSITY 7 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Application Information Light-to-Current and Voltage Conversion The ISL29006, ISL29007 and ISL29008 have responsiveness that is directly proportional to the intensity of light intercepted by the photodiode arrays. Conversion rate is independent of the light sources (fluorescent light, incandescent light or direct sunlight). 1.6 μ A I OUT = ⎛ ------------------⎞ × E ⎝ 100lux⎠ (EQ. 1) response of the ambient light detector for a given exposure of light. The example in Figure 20 shows a fully automatic dimming solution with no user interaction. Choose R1 and R2 values for any desired minimum brightness and slope. Choose C1 to adjust response time and to filter 50/60Hz room lighting. For example, suppose you wish to generate an output voltage from 0.25V to 1.2V to drive the input of an LED driver controller. The 0.25V represents the minimum LED brightness and 1.2V represents the maximum. The 1st step would be to determine the ratio of R1 and R2 in Equation 4: 3.0V R 1 = R 2 × ⎛ --------------- – 1⎞ = 11 × R 2 ⎝ 0.25V ⎠ (EQ. 4) Here, IOUT is the output current in µA, and E is the input light in lux. For some applications, a load resistor is added between the output and the ground, as shown in Figure 1. The output voltage can be expressed in Equation 2: 1.6 μ AV OUT = I OUT × R L = ⎛ ------------------⎞ × E × R L ⎝ 100lux⎠ (EQ. 2) 3V TO 5V SUPPLY VOLTAGE 3V DC VOLTAGE VDD Here, VOUT is the output voltage and RL is the value of the external load resistor. The compliance of the ISL29006's output circuit may result in premature saturation of the output current and voltage when an excessively large RL is used. The output compliance voltage is 300mV below the supply voltage as listed in VO-MAX of the “Electrical Specifications” table on page 3. In order to have the linear relationship between the input light and the output current and voltage, a proper resistor value (i.e., gain) should be picked for a specific input light range. The resistor value can be picked according to Equation 3: ( V SUP – 0.3V ) 100lux R L = -------------------------------------- × ----------------------1.6 μ A E RANGE (EQ. 3) R1 660k ISL29006 ISRC R2 60k TO INVERTER BRIGHTNESS INPUT OR LED DRIVER CONTROLLER C1 25µF GND FIGURE 20. Next, the value of R2 can be calculated based on the maximum output current coming from the ISL29006 under the application's maximum light exposure. Suppose the current has been determined to be about 2µA. Thus, R2 can be approximately calculated using Equations 5 and 6: 1.2V R 2 = ⎛ ------------⎞ = 60k Ω ⎝ 2μA⎠ (EQ. 5) Here, VSUP is the supply voltage and ERANGE is the specific input light range for an application. For example, an indoor light ranges typically from 0 lux to 1,000 lux. A resistor value of 270kΩ for 3V supply voltage can be used. For a small light range, a large resistor value should be used to achieve better sensitivity; for a large light range, a small resistor value should be used to prevent non-linear output current and voltage. and Equation 6: R 1 = 11 × R 2 = 660k Ω (EQ. 6) Application Examples The following examples present from fully automatic to fully manual override implementations. These guidelines are applicable to a wide variety of potential light control applications. The ISL29006, ISL29007 and ISL29008 can be used to control the brightness input of CCFL inverters. Likewise, it can interface well with LED drivers. In each specific application, it is important to recognize the target environment and its ambient light conditions. The mechanical mounting of the sensor, light aperture hole size and use of a light pipe or bezel are critical in determining the In Figure 20, the 3VDC supply can be replaced with a user adjustable bias control, such as 3V PWM control to allow control over the minimum and maximum output voltage. Figure 21 shows that ISL29006 is used to provide automatic dimming control. Short Circuit Current Limit The ISL29006, ISL29007 and ISL29008 do not limit the output short circuit current. If the output is directly shorted to the ground continuously, the output current could easily increase for a strong input light such that the device may be damaged. Maximum reliability is maintained if the output continuous current never exceeds 6mA by adding a load 8 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 resistor at the output. This limit is set by the design of the internal metal interconnects. ISL29008 has the capability of both sourcing and sinking current simultaneously. It may replace ISL29006 in sourcing current applications, or ISL29007 in sinking current applications. In applications that require both sourcing and sinking currents, for example in cases of mobile phones or PDAs where the display brightness needs to be proportional to ambient brightness while the key pads need to be inversely proportional to the brightness, ISL29008 offers the most economical solution for cost and footprint. Power Supply Bypassing and Printed Circuit Board Layout The ISL29006, ISL29007 and ISL29008 are relatively insensitive to the printed circuit board layout due to their low speed operation. Nevertheless, good printed circuit board layout is necessary for optimum performance. Ground plane construction is highly recommended; lead length should be as short as possible and the power supply pins must be well bypassed to reduce the risk of oscillation. For normal single supply operation where the GND pin is connected to ground, a 0.1µF ceramic capacitor should be placed from the VCC pin to the GND pin. A 4.7µF tantalum capacitor should then be connected in parallel, placed close to the device. Suggested PCB Footprint Footprint pads should be a nominal 1-to-1 correspondence with package pads. Since ambient light sensor devices do not dissipate high power, heat dissipation through the exposed pad is not important; instead, similar to DFN or QFN, the exposed pad provides robustness in the board mounting process. Therefore, we recommend that the exposed pad be soldered down for robust joint formation, but this is not mandatory. Optical Sensor Location Outline The green area in Figure 22 shows the optical sensor location outline of ISL29006, ISL29007 and ISL29008. Along the pin-out direction, the center line (CL) of the sensor coincides with that of the packaging. The sensor width in this direction is 0.39mm. Perpendicular to the pin-out direction, the CL of the sensor has a 0.19mm offset from the CL of packaging away from pin-1. The sensor width in this direction is 0.46mm. L1 22µH U2 EL7630 VIN R1 100k VIN LX MA2772800LCT-ND Rs FB 750 ENABLE PGND GND D2 D3 D1 D4 C1 1µF ENABLE D5 RLED 6.19 C2 1µF D6 GND C2 0.1µF 1 U1 VDD ISRC 6 2 GND NC EN 5 4 3 NC ISL29006 LIGHT SENSOR FIGURE 21. AUTOMATIC DIMMING CONTROL V FB ⎛ RS ⎞ 1.6 μ A I LED = -------------- – E • ⎛ ------------------⎞ • ⎜ -------------- + 1⎟ ⎝ 100lux⎠ ⎝ R R LED ⎠ LED (EQ. 7) 9 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 2.10mm 2.00mm 0.19mm 0.46mm 0.39mm FIGURE 22. 6 LD ODFN SENSOR LOCATION OUTLINE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 10 FN6282.1 September 21, 2010 ISL29006, ISL29007, ISL29008 Package Outline Drawing L6.2x2.1 6 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN) Rev 0, 9/06 2.10 A 6 PIN 1 INDEX AREA B 1 6 PIN 1 INDEX AREA 0.65 2.00 1 . 35 1 . 30 REF (4X) 0.10 6X 0 . 30 ± 0 . 05 0 . 65 TOP VIEW 0.10 M C A B 6X 0 . 35 ± 0 . 05 BOTTOM VIEW (0 . 65) MAX 0.75 SEE DETAIL "X" 0.10 C (0 . 65) (1 . 35) BASE PLANE ( 6X 0 . 30 ) SIDE VIEW SEATING PLANE 0.08 C C ( 6X 0 . 55 ) C (1 . 95) 0 . 00 MIN. 0 . 05 MAX. DETAIL "X" 0 . 2 REF 5 TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 11 FN6282.1 September 21, 2010