OPA773

OPA773 VLED Power Line Strip OPA773 • • • • 3, 0.5 watt LEDs per strip Mono-color per strip (Daylight White) Component beam angle 120° RoHS Compliant The OPA773 is designed for areas where light output and reliability are essential. The light beam angle of 120° is ideal for illuminating small and medium size areas while requiring minimal space. The devices are mounted on an FR-4 PC Board for ease of use with an easy to use IDC connector interface. For custom colors and design, contact your OPTEK representative. Applications • Architectural accent lighting • Under-counter lighting • Media illumination • • • Lighting for large channel letters Backlighting for light boxes Point-of-sale displays Optical and Electrical Characteristics - Daylight White (IF = 125 mA, TA = 25° C) Typical Forward Voltage (V) Typical Luminous Flux (lm) Beam Angle Color Typical CCT Connector Insertion Tool Wire Size Min/Max 14 to 16 63 120° Daylight White 5,750°K IDC (AVX #00 9175 002 001 006) AVX #9175 series 26 AWG or 28 AWG NOTES: 1. All electrical and optical characteristics of the LEDs remain the same as specified in Optek Datasheet OVS5WBCR4. 2. Maximum storage and operating temperature –40° ~ +100°C. 3. ESD threshold (HBM) 2000V 4. 14-16 VDC power supply not included. 0.2A minimum rating required. DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com Issue B 01/2012 Page 1 of 2 OPA773 VLED Power Line Strip Suggested Design Options: Optek Part Number Number of LEDs per Strip Number of Strips per Buss LED Drive Current per Strip AWG Supply Voltage OPA773 3 1 to 5 125mA 26-28 14-16V OVPL5W3K*** 3 5 Included 125mA 26-28 14-16V Optek Custom Assembly** Other Other Other Other Other NOTES ** *** Contact Optek or an authorized distributor to discuss your application Design kit includes 5 / OPA773 power line strips, wire harnesses and insertion tool. OVPL5W3K Mounting Instructions: 1. Install backplane (not included) behind panel to be illuminated. 2. Use masking tape (not included) to temporarily position the boards on backplane. 3. Route wire harness to each strip: • Start with loose end and work toward 2.1mm jack. • Use insertion tool to insert red and black wires on each board. • Leave several inches of slack between each strip. 4. Connect the 2.1mm jack to 14-16V power supply (not included, must be rated at 1.0A minimum). 5. Reposition all boards until optimal illumination is achieved. 6. Peel tape backing from boards. 7. Permanently apply boards to backplane. Note: Steps 6 and 7 are optional—do not peel off backing if the kit will be reused. Output connector 2.1mm ID/5.5mm OD OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 01/2012 Page 2 of 2 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com