OPB483T11

      Choice of pins or wires mounting configuration Choice of aperture Choice of output configuration Choice of opaque or IR transmissive shell material Data rates to 250 kBaud Low power consumption The OPB460, OPB470, OPB480 and OPB490 series of Photologic® photo integrated circuit switches provide optimum flexibility for the design engineer. Building from a standard housing with a 0.125” (3.180 mm) wide slot, a user can specify the type and polarity of TTL output, discrete shell material, aperture width and choice of mounting configurations. OPB460 through OPB473 have 0.425” (10.795 mm) PCBoard leads with 0.320” (8.1 mm) spacing. OPB480 through OPB493 have 24” (609 mm) 26 AWG wires (UL approved wires). All devices in this series exhibit performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as buffered or inverted with 10 kW Pull-up or Open Collector output. Devices are also TTI/LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications:  Mechanical switch replacement  Speed indication (tachometer)  Mechanical limit indication  Edge sensing Part Number Guide — OPB460, OPB470, OPB480, OPB490 Series OPB 4 X X X 1 1 X OPTEK Assembly All PCBoard Versions RoHS Compliant: Z = Wire Version RoHS Compliant Photologic™ Sensor Family Discrete Housing Material: 6 — Transmissive Shell, PCBoard Mountable 7 — Opaque Shell, PCBoard Mountable 8 — Transmissive Shell, Wire Termination 9 — Opaque Shell, Wire Termination Electrical Specifications: 0 — Buffered 10 kΩ Output 1 — Buffered Open-Collector Output 2 — Inverted 10 kΩ Output 3 — Inverted Open-Collector Output RoHS Sensor Aperture: 1 = 0.010” [0.25 mm] Emitter Aperture: 1 = 0.010” [0.25 mm] Mounting Configurations: L — Emitter side mounting tab only N — No mounting tabs P — Sensor side mounting tab only T — Two mounting tabs TOLERANCE DIMENSIONS ARE: ± .25mm [± .010”] CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK’s molded plastics. Applies to: OPB460, OPB470, OPB480, OPB490. Color-Pin Description Red-1 Anode Black-2 Cathode White-3 Vcc Blue-4 Output Green-5 Ground Storage & Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] Supply Voltage, VCC (not to exceed 3 seconds) -40° C to +85° C (1) 260°C 18 V Diode Forward DC Current 40 mA Diode Reverse DC Voltage 2V Input Diode Power Dissipation(2) 75 mW Voltage at Output Lead (Open Collector Output) Output Photologic® Power Dissipation Total Device Power Dissipation(4) Notes: (1) (2) (3) (4) (5) (6) (3) 25 V 200 mW 275 mW RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/°C above 25° C (OPB460, OPB470) or derate linearly 1.82 mW/°C above 25° C (OPB480, OPB490). Derate linearly 1.50 mW/°C above 25° C (OPB460, OPB470) or derate linearly 1.64 mW/°C above 25° C(OPB480, OPB490). Derate linearly 3.17 mW/°C above 25° C (OPB460, OPB470) or derate linearly 3.45 mW/°C above 25° C (OPB480, OPB490). The OPB460/OPB470 series are terminated with 0.020” square leads designed for printed circuit board mounting. The OPB480/OPB490 series of switches are terminated with 24” (609.600 mm) of 7-strand 26 AWG, UL rated insulated wire on each terminal. Insulation colors and functions are: red (anode), black (cathode), white (VCC,), blue (output) and green (ground). Other wire lengths and/or colors in addition to customer selected connectors are available. Contact your local representative or call the factory. OPB460/470/480/490 Buffered 10K Pull-Up OPB461/471/481/491 Buffered Open-Collector OPB462/472/482/492 Inverted 10K Pull-Up OPB463/473/483/493 Inverted Open-Collector VF Forward Voltage - - 1.7 V IF = 20 mA, TA = 25° C IR Reverse Current - - 100 µA VR = 2 V, TA = 25° C 4.5 - 16 V Output Photologic® Sensor VCC Operating DC Supply Voltage - - 7.5 mA VCC = 16 V, IF = 0 mA(1) ICCL Low Level Supply Current: Buffered with 10k pull-up(1) Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output - - 7.5 mA VCC = 16 V, IF = 12 mA High Level Supply Current: Buffered with 10k pull-up Buffered Open-Collector Output - - 7.5 mA VCC = 16 V, IF = 12 mA Inverted with 10k pull-up: Inverted Open-Collector Output - - 7.5 mA VCC = 16 V, IF = 0 mA(1) Low Level Output Voltage: Buffered with 10k pull-up Buffered Open-Collector Output - - 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 0 mA Inverted with 10k pull-up: Inverted Open-Collector Output - - 0.4 V VCC = 4.5 V, IF = 12 mA(1) High Level Output Voltage: Buffered with 10k pull-up VCC -1.5 - - V VCC = 4.5 V to 16 V, No Load, IF = 12 mA Inverted with 10k pull-up: Inverted Open-Collector Output(1) VCC -1.5 - - V VCC = 4.5 V to 16 V, No Load, IF = 0 mA High Level Output Voltage: Buffered Open-Collector Output - - 14 µA VCC = 16 V, IF = 12 mA, VOH = 25 V, TA = 25° C Inverted with 10k pull-up: Inverted Open-Collector Output(1) - - 14 µA VCC = 16 V, IF = 0 mA, VOH = 25 V, TA = 25° C LED Positive-Going Threshold Current - - 10 mA VCC = 5 V, TA = 25° C Hysteresis - 1.4 - - Rise Time, Fall Time - 50 - ns VCC = 5 V, TA = 25° C, IF = 0 or 12 mA Propagation Delay - 3 - µs RL = 300 Ω to 5 V, CL = 50 pF ICCH VOL VOH IOH IF(+) IF(+)/IF(-) trtf tPLHtPHL Notes: (1) Normal application would be with light source blocked, simulated by IF = 0 mA. (2) All parameters tested using pulse technique. VCC = 5 V OPB480T55 - Flag Next to Emitter OPB480T55 - Flag Next to Sensor 1.20 1.20 Top to Bottom (Back) Top to Bottom (Back) Top to Bottom 1.00 1.00 0.80 0.80 Right to Left Logic Right to Left Logic Top to Bottom Right to Left (Back) 0.60 Right to Left (Back) 0.60 0.40 0.40 Left to Right Left to Right Left to Right (Back) Left to Right (Back) 0.20 0.20 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 0.10 0.15 Displacement Distance (inches) OPB480T55 - Flag in Middle of Slot 1.20 Top to Bottom (Back) Top to Bottom 1.00 0 Top to Bottom 0.80 Logic Right to Left Right to Left (Back) 0.60 Emitter Left to Right Right to Left 0.40 Sensor Left to Right Left to Right (Back) 0 0.20 0.00 0.00 0.05 0.10 0.15 0.20 Displacement Distance (inches) 0.20 Displacement Distance (inches) 0.25 Width 0.25 OPB481N51 - Flag Next to Emitter OPB481N51 - Flag Next to Sensor 1.20 1.20 Top to Bottom (Back) Top to Bottom Top to Bottom (Back) 1.00 1.00 0.80 0.80 Top to Bottom Right to Left Logic Logic Right to Left Right to Left (Back) 0.60 0.40 Right to Left (Back) 0.60 0.40 Left to Right Left to Right Left to Right (Back) Left to Right (Back) 0.20 0.00 0.00 0.20 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 0.10 0.15 OPB481N51 - Flag in Middle of Slot 1.20 Top to Bottom (Back) Top to Bottom 1.00 0 Top to Bottom 0.80 Logic Right to Left Right to Left (Back) 0.60 Emitter Left to Right Right to Left 0.40 Left to Right Sensor Left to Right (Back) 0 0.20 0.00 0.00 0.05 0.10 0.15 0.20 Displacement Distance (inches) 0.20 Displacement Distance (inches) Displacement Distance (inches) 0.25 Width 0.25 OPB460N11 - Flag Next to Sensor OPB460N11 - Flag Next to Emitter 1.20 1.20 Top to Bottom (Back) Top to Bottom Top to Bottom (Back) 1.00 1.00 0.80 0.80 Right to Left Logic Logic Right to Left 0.60 Right to Left (Back) 0.40 Right to Left (Back) 0.60 0.40 Left to Right Left to Right Left to Right (Back) Left to Right (Back) 0.20 0.00 0.00 Top to Bottom 0.20 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) 0.00 0.00 0.05 0.10 0.15 OPB460N11 - Flag in Middle of Slot 1.20 Top to Bottom (Back) Top to Bottom 1.00 0 Top to Bottom 0.80 Logic Right to Left Right to Left (Back) 0.60 Emitter Left to Right Right to Left 0.40 Left to Right Sensor Left to Right (Back) 0 0.20 0.00 0.00 0.05 0.10 0.15 0.20 Displacement Distance (inches) 0.20 Displacement Distance (inches) 0.25 Width 0.25