OPI1264B

Optically Coupled Isolator OPI110, OPI1264 Series Features:  15 kV electrical isola on  Choice of phototransistor  Low‐cost plas c housing  UL recognized File No. E58730 Description: Each Optoisolator in this data sheet contains an infrared Light Emi ng Diode (LED) and a NPN silicon Photosensor. The OPI110 and OPI1264 devices have 890 nm Light Emi ng Diode (LED) and NPN phototransistor sensor. The devices are sealed in a precast opaque housing with a op cally transmissive path between the LED and the photosensor. The Optoisolators in this data sheet are UL recognised under E58730. This series is designed for transmission of informa on between one power supply voltage and another where the poten als during surge condi ons are not greater than the guaranteed isola on voltage. Custom electrical, wire and cabling and connectors are available. Contact your local representa ve or OPTEK for more informa on. Applications: High voltage isola on between input and output Electrical isola on in dirty environments Industrial equipment Medical equipment Office equipment Ordering InformaƟon Part Number LED Peak Wavelength Sensor IsolaƟon Voltage (,000) CTR Min / Max VCE Lead Length / (Volts) Spacing Max 12.5 / NA OPI110 OPI110A 25 / NA 10 / 40 Transistor OPI110B 50 / 125 OPI110C 100 / NA 30 15 890 nm OPI1264 25 / NA Transistor 10 / 40 OPI1264B 50 / 125 OPI1264C 100 / NA General Note TT Electronics reserves the right to make changes in product specifica on without no ce or liability. All informa on is subject to TT Electronics’ own data and is considered accurate at me of going to print. 0.50" / 0.55" 12.5 / NA OPI1264A © TT electronics plc IF (mA) Typ / Max TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www. electronics.com | sensors@ electronics.com Rev D 10/2022 Page 1 Optically Coupled Isolator OPI110, OPI1264 Series Electrical Specifications Absolute Maximum RaƟngs (TA = 25o C unless otherwise noted) Storage Temperature ‐40° C to +100° C Opera ng Temperature ‐40° C to +85° C (1)(2) Input‐to‐Output Isola on Voltage ± 15 kVDC Lead Soldering Temperature (1/16” (1.6 mm) from case for 5 seconds with soldering iron) (3) 260° C Input Diode Forward DC Current 40 mA Reverse DC Voltage 2V Power Dissipa on(4) 50 mW Output Photosensor Collector‐Emi er Voltage OPI110, OPI1264 30 Emi er‐Collector Voltage 5 Power Dissipa on (5) 100 mW Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. (2) UL recogni on is for 15 kV dc for one minute. (3) RMA flux is recommended. The dura on can be extended to 10 seconds maximum when flow soldering. (4) Derate linearly 0.83 mW/°C above 25° C. (5) Derate linearly 1.67 mW/°C above 25° C.. OPI1264 1 4 2 3 OPI110 General Note TT Electronics reserves the right to make changes in product specifica on without no ce or liability. All informa on is subject to TT Electronics’ own data and is considered accurate at me of going to print. © TT electronics plc 1 4 2 3 TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www. electronics.com | sensors@ electronics.com Rev D 10/2022 Page 2 Optically Coupled Isolator OPI110, OPI1264 Series Electrical CharacterisƟcs (TA = 25o C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP265 for addi onal informa on ‐ for reference only) VF Forward Voltage ‐ ‐ 1.6 V IF = 20 mA IR Reverse Current ‐ ‐ 100 µA VR = 2 V Output Photosensor (See OP505 for addi onal informa on ‐ for reference only) V(BR)CEO Collector‐Emi er Breakdown Voltage OPI110, OPI1264 30 ‐ ‐ V IC = 100 µA V(BR)ECO Emi er‐Collector Breakdown Voltage OPI110 OPI1264 5 ‐ ‐ ‐ ‐ ‐ V IE = 100 µA, IF = 0 IE = 100 µA Collector‐Emi er Dark Current OPI110, OPI1264 ‐ ‐ 100 1.25 ‐ 44 12.5 25.0 50.0 100.0 ‐ ‐ ‐ ‐ ‐ ‐ 125 ‐ ICEO nA VCE = 15 V, EE = 0 Coupled IC(ON) Coupled “ON” Current OPI110, OPI1264 IC/IF DC Current Transfer Ra o OPI110, OPI1264 OPI110A, OPI1264A OPI110B, OPI1264B OPI110C, OPI1264C Collector Satura on Voltage OPI110, OPI1264 ‐ ‐ 0.4 ICEO Collector‐Emi er Dark Current OPI110, OPI1264 ‐ ‐ 200 VISO Isola on Voltage 15 ‐ ‐ VCE(SAT) mA % V nA kVDC IF = 10mA VCE = 5V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, IC = 1.6 mA VCE = 20 V, IF = 0 See Note 1. Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. General Note TT Electronics reserves the right to make changes in product specifica on without no ce or liability. All informa on is subject to TT Electronics’ own data and is considered accurate at me of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www. electronics.com | sensors@ electronics.com Rev D 10/2022 Page 3