OVLGY0C9B9

High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Features: • • • • Narrow beam angle High brightness LED Water clear plastic package UV resistant epoxy Description: Each device in the OVLG Series is a high intensity LED mounted in a clear plastic T-1¾ package. Each device incorporates an integral molded lens that enables a narrow beam angle and provides an even emission pattern. Designed to produce light over a wide range of drive currents, these LEDs are useful in applications that require a higher on-axis brightness than that achievable with standard lamps. Applications: • • • • Indoor/outdoor applications Variable message boards Store front signage Indicators Part Number OVLGB0C6B9 OVLGC0C6B9 OVLGS0C8B9 OVLGY0C9B9 Material Emitted Color Intensity Typ. mcd Lens Color Blue Blue-Green Red Yellow 7,200 23,000 14,000 14,000 Clear InGaN AlInGaP RoHS General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 1 High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Electrical Specifications Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature Range -40 ~ +100 °C Operating Temperature Range -40 ~ +100 °C Reverse Voltage 5V Blue, Blue-Green Continuous Forward Current 25 mA Red, Yellow 50 mA Peak Forward Current (10% Duty Cycle, 1 kHz) 100 mA Power Dissipation Current Linearity vs Ambient Temperature Blue, Blue-Green 100 mW Red, Yellow 120 mW Blue, Blue-Green -0.29 mA/° C Red, Yellow -0.72 mA/° C LED Junction Temperature 125° C Electrostatic Discharge Classification (JEDEC-JESD22-A114F) Class 1C 1 Lead Soldering Temperature (3 mm from the base of the epoxy bulb) 260° C / 5 seconds Electrical Characteristics (TA = 25o C unless otherwise noted) SYMBOL PARAMETER IV Luminous Intensity COLOR MIN TYP MAX Blue 4,360 7,200 ---- Blue-Green 11,970 23,000 ---- Red 8,550 14,000 ---- Yellow 8,550 14,000 ---- 2.6 3.2 4.0 Blue VF Forward Voltage Blue-Green Red 1.8 2.0 2.4 ---- ---- 10 Blue 460 470 475 Blue-Green 499 505 511 Red 620 623 630 Yellow 585 589 595 Blue ---- 15 ---- Blue-Green ---- 15 ---- Red ---- 8 ---- Yellow ---- 8 ---- Yellow UNITS CONDITIONS mcd IF = 20 mA V IF = 20 mA µA VR = 5 V nm IF = 20 mA deg IF = 20 mA Blue IR Reverse Current Blue-Green Red Yellow λD 2Θ½H-H Dominant Wavelength 50% Power Angle General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 2 High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Typical Electro-Optical Characteristics Curves—Blue & Blue-Green General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 3 High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Typical Electro-Optical Characteristics Curves—Red & Yellow General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 4 High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Beam Angle: Packaging: 500 pcs per anti-static bag with desiccant Desiccant Barcode Label General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 5 High-Intensity LED in Plastic T-1¾ Package OVLGx0CyB9 Series Reliability Test LED lamps are checked by reliability tests based on MIL standards. 1. Test Conditions, Acceptable Criteria & Results Life Test Operation Life Test (OLT) MIL-STD-750D Method 1026.3 TA=25°C , IF=30mA * 1000 Hrs 100 0/1 Pass High Temperature Storage (HTS) MIL-STD-750D Method 1032.1 TA=100°C 1000 Hrs 100 0/1 Pass Low Temperature Storage (LTS) MIL-STD-750D Method 1032.1 TA=—40°C 1000 Hrs 100 0/1 Pass Temp. & Humidity with Bias (THB) MIL-STD-750D Method 103B TA=85°C , Rh=85% IF=20mA 500 Hrs 100 0/1 Pass Thermal Shock Test (TST) MIL-STD-750D Method 1056.1 0°C ~ 2min 100°C 2min 100 cycles 100 0/1 Pass Temperature Cycling Test (TCT) MIL-STD-750D Method 1051.5 -40°C ~ 25°C ~ 100°C ~ 25°C 30min 5min 30min 5min 100 cycles 100 0/1 Pass Solderability MIL-STD-750D Method 2026.4 235±5°C , 5 sec. 1 time 20 0/1 Pass Resistance to Soldering Heat MIL-STD-750D Method 2031.1 260±5°C , 5 sec. 1 time 20 0/1 Pass Lead Integrity MIL-STD-750D Method 2036.3 Load 2.5N (0.25kgf) 0°~90°~0° , bend 3 times 20 0/1 Pass Environmental Test Test Item Mechanical Test Std. Test Method Test Conditions Duration Unit Acc / Rej Result Criteria Classification Remark: ( * ) IF = 30mA for AllnGaP chip; IF = 20mA for InGan chip ( ** ) IF = 20mA for AllnGaP chip; IF = 10mA for InGan chip 2. Failure Criteria (TA = 25°C): Test Item Symbol Test Conditions Luminous Intensity IV IF = 20mA Forward Voltage VF IF = 20mA Criteria for Judgment Min. Max LSLx0.7 ** USLx1.1 * ( * ) USL: Upper Standard Level, ( ** ) LSL: Lower Standard Level General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc TT Electronics | OPTEK Technology 2900 E. Plano Pkwy, Plano, TX 75074 | Ph: +1 972 323 2200 www.ttelectronics.com | sensors@ttelectronics.com Rev C 10/2015 Page 6