IS63LV1024L-8JI

IS63LV1024 IS63LV1024L 128K x 8 HIGH-SPEED CMOS STATIC RAM 3.3V REVOLUTIONARY PINOUT FEATURES • High-speed access times: 8, 10, 12 ns • High-performance, low-power CMOS process • Multiple center power and ground pins for greater noise immunity • Easy memory expansion with CE and OE options • CE power-down • Fully static operation: no clock or refresh required • TTL compatible inputs and outputs • Single 3.3V power supply • Packages available: – 32-pin 300-mil SOJ – 32-pin 400-mil SOJ – 32-pin TSOP (Type II) – 32-pin STSOP (Type I) – 36-pin BGA (8mmx10mm) • Lead-free Available JANUARY 2007 DESCRIPTION The ISSI IS63LV1024/IS63LV1024L is a very high-speed, low power, 131,072-word by 8-bit CMOS static RAM in revolutionary pinout. The IS63LV1024/IS63LV1024L is fabricated using ISSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields higher performance and low power consumption devices. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down to 250 µW (typical) with CMOS input levels. The IS63LV1024/IS63LV1024L operates from a single 3.3V power supply and all inputs are TTL-compatible. FUNCTIONAL BLOCK DIAGRAM A0-A16 DECODER 128K X 8 MEMORY ARRAY VDD GND I/O DATA CIRCUIT I/O0-I/O7 COLUMN I/O CE OE WE CONTROL CIRCUIT Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 1 IS63LV1024 IS63LV1024L PIN CONFIGURATION 32-Pin SOJ PIN CONFIGURATION 32-Pin TSOP (Type II) (T) 32-Pin STSOP (Type I) (H) A0 A1 A2 A3 CE I/O0 I/O1 VDD GND I/O2 I/O3 WE A4 A5 A6 A7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 A16 A15 A14 A13 OE I/O7 I/O6 GND VDD I/O5 I/O4 A12 A11 A10 A9 A8 A0 A1 A2 A3 CE I/O0 I/O1 VDD GND I/O2 I/O3 WE A4 A5 A6 A7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 A16 A15 A14 A13 OE I/O7 I/O6 GND VDD I/O5 I/O4 A12 A11 A10 A9 A8 PIN DESCRIPTIONS A0-A16 CE OE WE I/O0-I/O7 VDD GND Address Inputs Chip Enable Input Output Enable Input Write Enable Input Data Inputs/Outputs Power Ground PIN CONFIGURATION 36-mini BGA (B) (8 mm x 10 mm) 1 2 3 4 5 6 A B C D E F G H A0 I/O4 I/O5 GND VDD I/O6 I/O7 A9 A1 A2 NC WE NC A3 A4 A5 A6 A7 A8 I/O0 I/O1 VDD GND NC OE A10 CE A11 NC A16 A12 A15 A13 I/O2 I/O3 A14 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 IS63LV1024 IS63LV1024L TRUTH TABLE Mode Not Selected (Power-down) Output Disabled Read Write WE X H H L CE H L L L OE X H L X I/O Operation High-Z High-Z DOUT DIN VDD Current ISB1, ISB2 ICC1, ICC2 ICC1, ICC2 ICC1, ICC2 ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM TSTG PT Parameter Terminal Voltage with Respect to GND Storage Temperature Power Dissipation Value –0.5 to VDD + 0.5 –65 to +150 1.0 Unit V °C W Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING RANGE Range Commercial Industrial Ambient Temperature 0°C to +70°C –40°C to +85°C VDD 3.3V ± 0.3V 3.3V ± 0.15V DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Parameter VOH VOL VIH VIL ILI ILO Output HIGH Voltage Output LOW Voltage Input HIGH Voltage Input LOW Voltage(1) Input Leakage Output Leakage GND ≤ VIN ≤ VDD GND ≤ VOUT ≤ VDD, Outputs Disabled Com. Ind. Com. Ind. Test Conditions VDD = Min., IOH = –4.0 mA VDD = Min., IOL = 8.0 mA Min. 2.4 — 2.2 –0.3 –1 –5 –1 –5 Max. — 0.4 VDD + 0.3 0.8 1 5 1 5 Unit V V V V µA µA Notes: 1. VIL = –3.0V for pulse width less than 10 ns. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 3 IS63LV1024 IS63LV1024L IS63LV1024 POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter ICC1 VDD Operating Supply Current Test Conditions VDD = Max., CE = VIL IOUT = 0 mA, f = Max. Com. Ind. typ.(2) Ind. (@15 ns) Com. Ind. Com. Ind. Com. Ind. typ.(2) -8 ns Min. Max. — — — — — — — — — — 160 170 105 55 55 25 30 5 10 0.5 -10 ns Min. Max. — — — — — — — — — — 150 160 95 45 45 25 30 5 10 0.5 -12 ns Min. Max. — — — — — — — — — — — 130 140 75 90 40 40 25 30 5 10 0.5 Unit mA ISB TTL Standby Current (TTL Inputs) TTL Standby Current (TTL Inputs) CMOS Standby Current (CMOS Inputs) VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = Max VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 VDD = Max., CE ≥ VDD – 0.2V, VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 mA ISB1 mA ISB2 mA Notes: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 2. Typical values are measured at VDD = 3.3V, TA = 25oC. Not 100% tested. IS63LV1024L POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter ICC1 VDD Operating Supply Current TTL Standby Current (TTL Inputs) TTL Standby Current (TTL Inputs) CMOS Standby Current (CMOS Inputs) Test Conditions VDD = Max., CE = VIL IOUT = 0 mA, f = Max. VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = Max VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 VDD = Max., CE ≥ VDD – 0.2V, VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 Com. Ind. typ.(2) Com. Ind. Com. Ind. Com. Ind. typ.(2) -8 ns Min. Max. — — — — — — — — — — 100 110 75 35 40 15 20 1 1.5 0.05 -10 ns Min. Max. — — — — — — — — — — 95 105 70 30 35 15 20 1 1.5 0.05 -12 ns Min. Max. — — — — — — — — — — 90 100 65 25 30 15 20 1 1.5 0.05 Unit mA ISB mA ISB1 mA ISB2 mA Notes: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 2. Typical values are measured at VDD = 3.3V, TA = 25oC. Not 100% tested. CAPACITANCE(1,2) Symbol CIN CI/O Parameter Input Capacitance Input/Output Capacitance Conditions VIN = 0V VOUT = 0V Max. 6 8 Unit pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V. 4 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 IS63LV1024 IS63LV1024L READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter Read Cycle Time Address Access Time Output Hold Time CE Access Time OE Access Time OE to Low-Z Output OE to High-Z Output CE to Low-Z Output CE to High-Z Output CE to Power Up Time CE to Power Down Time -8 ns Min. Max. 8 — 2 — — 0 0 3 0 0 — — 8 — 8 4 — 4 — 4 — 8 -10 ns Min. Max. 10 — 2 — — 0 0 3 0 0 — — 10 — 10 5 — 5 — 5 — 10 -12 ns Min. Max. 12 — 2 — — 0 0 3 0 0 — — 12 — 12 6 — 6 — 6 — 12 Unit ns ns ns ns ns ns ns ns ns ns ns tRC tAA tOHA tACE tDOE tLZOE(2) tHZOE(2) tLZCE tPU tPD (2) (2) tHZCE Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V loading specified in Figure 1. 2. Tested with the loading specified in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Levels Output Load Unit 0V to 3.0V 3 ns 1.5V See Figures 1 and 2 AC TEST LOADS 317 Ω ZOUT = 50 Ω OUTPUT 50 Ω VT = 1.5V Figure 1 Figure 2 3.3V OUTPUT 5 pF Including jig and scope 351 Ω Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 5 IS63LV1024 IS63LV1024L AC WAVEFORMS READ CYCLE NO. 1(1,2) t RC ADDRESS t AA t OHA DOUT PREVIOUS DATA VALID t OHA DATA VALID READ1.eps READ CYCLE NO. 2(1,3) t RC ADDRESS t AA OE t OHA t DOE CE t HZOE t LZOE t ACE t LZCE t HZCE DATA VALID CE_RD2.eps DOUT HIGH-Z Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE = VIL. 3. Address is valid prior to or coincident with CE LOW transitions. 6 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 IS63LV1024 IS63LV1024L WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range) Symbol Parameter Write Cycle Time CE to Write End Address Setup Time to Write End Address Hold from Write End Address Setup Time (1) -8 ns Min. Max. 8 7 8 0 0 7 8 5 0 — 3 — — — — — — — — — 4 — -10 ns Min. Max. 10 7 8 0 0 7 10 5 0 — 3 — — — — — — — — — 5 — -12 ns Min. Max. 12 8 8 0 0 8 12 6 0 — 3 — — — — — — — — — 6 — Unit ns ns ns ns ns ns ns ns ns ns ns tWC tSCE tAW tHA tSA tPWE1 tSD tHD tHZWE (2) WE Pulse Width (OE High) WE Pulse Width (OE Low) Data Setup to Write End Data Hold from Write End WE LOW to High-Z Output WE HIGH to Low-Z Output tPWE2(2) tLZWE(2) Notes: 1. Test conditions assume signal transition times of 3ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. AC WAVEFORMS WRITE CYCLE NO. 1(1,2 (CE Controlled, OE = HIGH or LOW) t WC ADDRESS VALID ADDRESS t SA CE t SCE t HA WE t AW t PWE1 t PWE2 t HZWE t LZWE HIGH-Z DOUT DATA UNDEFINED t SD DIN t HD DATAIN VALID CE_WR1.eps Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 7 IS63LV1024 IS63LV1024L AC WAVEFORMS WRITE CYCLE NO. 2(1) (WE Controlled, OE = HIGH during Write Cycle) t WC ADDRESS VALID ADDRESS t HA OE CE LOW t AW t PWE1 WE t SA DOUT DATA UNDEFINED t HZWE HIGH-Z t LZWE t SD DIN t HD DATAIN VALID CE_WR2.eps WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle) t WC ADDRESS OE CE VALID ADDRESS LOW t HA LOW t AW t PWE2 WE tSA DOUT DATA UNDEFINED t HZWE HIGH-Z t LZWE t SD DIN t HD DATAIN VALID CE_WR3.eps Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 2. I/O will assume the High-Z state if OE > VIH. 8 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 IS63LV1024 IS63LV1024L DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter VDD for Data Retention Data Retention Current Data Retention Setup Time Recovery Time Test Condition See Data Retention Waveform VDD = 2.0V, CE ≥ VDD – 0.2V See Data Retention Waveform See Data Retention Waveform O Options IS63LV1024 IS63LV1024L Min. 2.0 — — 0 Typ.(1) — 0.5 0.05 — — Max. 3.6 10 1.5 — — Unit V mA ns ns VDR IDR tSDR tRDR tRC Note 1: Typical values are measured at VDD = 3.0V, TA = 25 C and not 100% tested. DATA RETENTION WAVEFORM (CE Controlled) tSDR VDD Data Retention Mode tRDR VDR CE ≥ VDD - 0.2V CE GND Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 9 IS63LV1024 IS63LV1024L IS63LV1024 ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) 8 10 Order Part No. IS63LV1024-8K IS63LV1024-8KL IS63LV1024-10T IS63LV1024-10J IS63LV1024-10K IS63LV1024-12T IS63LV1024-12J IS63LV1024-12KL Package 400-mil Plastic SOJ 400-mil Plastic SOJ, Lead-free TSOP (Type II) 300-mil Plastic SOJ 400-mil Plastic SOJ TSOP (Type II) 300-mil Plastic SOJ 400-mil Plastic SOJ, Lead-free 12 Industrial Range: –40°C to +85°C Speed (ns) 8 10 12 Order Part No. IS63LV1024-8KI IS63LV1024-10KI IS63LV1024-12TI Package 400-mil Plastic SOJ 400-mil Plastic SOJ TSOP (Type II) 10 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 IS63LV1024 IS63LV1024L IS63LV1024L ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) 8 10 Order Part No. IS63LV1024L-8T IS63LV1024L-8B IS63LV1024L-10T IS63LV1024L-10TL IS63LV1024L-10HL IS63LV1024L-12T IS63LV1024L-12H IS63LV1024L-12J IS63LV1024L-12JL IS63LV1024L-12B Package TSOP (Type II) mBGA (8mmx10mm) TSOP (Type II) TSOP (Type II), Lead-free sTSOP (Type I) (8mm x13.4mm), Lead-free TSOP (Type II) sTSOP (Type I) (8mm x13.4mm) 300-mil Plastic SOJ 300-mil Plastic SOJ, Lead-free mBGA (8mmx10mm) 12 Industrial Range: –40°C to +85°C Speed (ns) 8 Order Part No. IS63LV1024L-8TI IS63LV1024L-8JI IS63LV1024L-8KI IS63LV1024L-8BI IS63LV1024L-10HI IS63LV1024L-10JLI IS63LV1024L-10KLI IS63LV1024L-10TLI IS63LV1024L-12BI IS63LV1024L-12BLI IS63LV1024L-12TI Package TSOP (Type II) 300-mil Plastic SOJ 400-mil Plastic SOJ mBGA (8mmx10mm) sTSOP (Type I) (8mm x13.4mm) 300-mil Plastic SOJ, Lead-free 400-mil Plastic SOJ, Lead-free TSOP (Type II), Lead-free mBGA (8mmx10mm) mBGA (8mmx10mm), Lead-free TSOP (Type II) 10 12 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. I 1/26/07 11 PACKAGING INFORMATION 400-mil Plastic SOJ Package Code: K N N/2+1 E1 E Notes: 1. Controlling dimension: millimeters. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Reference document: JEDEC MS-027. 1 N/2 D A SEATING PLANE b C A2 e B A1 E2 Symbol No. Leads A A1 A2 B b C D E E1 E2 e Millimeters Inches Min Max Min Max (N) 28 3.25 3.75 0.128 0.148 0.64 — 0.025 — 2.08 — 0.082 — 0.38 0.51 0.015 0.020 0.66 0.81 0.026 0.032 0.18 0.33 0.007 0.013 18.29 18.54 0.720 0.730 11.05 11.30 0.435 0.445 10.03 10.29 0.395 0.405 9.40 BSC 0.370 BSC 1.27 BSC 0.050 BSC Millimeters Min Max 32 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 20.82 21.08 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.820 0.830 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Millimeters Min Max 36 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 23.37 23.62 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.920 0.930 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 PACKAGING INFORMATION Millimeters Inches Symbol Min Max Min Max No. Leads (N) 40 A 3.25 3.75 0.128 0.148 A1 0.64 — 0.025 — A2 2.08 — 0.082 — B 0.38 0.51 0.015 0.020 b 0.66 0.81 0.026 0.032 C 0.18 0.33 0.007 0.013 D 25.91 26.16 1.020 1.030 E 11.05 11.30 0.435 0.445 E1 10.03 10.29 0.395 0.405 E2 9.40 BSC 0.370 BSC e 1.27 BSC 0.050 BSC Millimeters Min Max 42 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 27.18 27.43 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.070 1.080 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Millimeters Min Max 44 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 28.45 28.70 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.120 1.130 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Inches Min Max Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 PACKAGING INFORMATION 300-mil Plastic SOJ Package Code: J N E1 E 1 D A SEATING PLANE B A2 C e b A1 E2 MILLIMETERS Sym. N0. Leads A A1 A2 b B C D E E1 E2 e — 0.64 2.41 0.41 0.66 0.20 17.02 8.26 7.49 6.27 INCHES Min. Typ. Max. Min. Typ. Max. 24/26 — — — — — — — — — — 3.56 — 2.67 0.51 0.81 0.25 17.27 8.76 7.75 7.29 Notes: 1. Controlling dimension: inches, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. — 0.025 0.095 0.016 0.026 0.008 0.670 0.325 0.295 0.247 — 0.140 — — — — — — — — — — 0.105 0.020 0.032 0.010 0.680 0.345 0.305 0.287 1.27 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 02/25/03 PACKAGING INFORMATION 300-mil Plastic SOJ Package Code: J MILLIMETERS Sym. N0. Leads A A1 A2 b B C D E E1 E2 e — 0.64 2.41 0.41 0.66 0.20 18.29 8.26 7.49 6.27 INCHES Min. Typ. Max. Sym. N0. Leads MILLIMETERS Min. Typ. Max. 32 — 0.64 2.41 0.41 0.66 0.20 20.83 8.26 7.49 6.27 — — — — — — — — — — 3.56 — 2.67 0.51 0.81 0.25 21.08 8.76 7.75 7.29 — INCHES Min. Typ. Max. Min. Typ. Max. 28 — — — — — — — — — — 3.56 — 2.67 0.51 0.81 0.25 18.54 8.76 7.75 7.29 — 0.025 0.095 0.016 0.026 0.008 0.720 0.325 0.295 0.247 — — — — — — — — — — 0.140 — 0.105 0.020 0.032 0.010 0.730 0.345 0.305 0.287 A A1 A2 b B C D E E1 E2 e — — — — — — — — — — 0.140 — 0.105 0.020 0.032 0.010 0.830 0.345 0.305 0.287 0.025 0.095 0.016 0.026 0.008 0.820 0.325 0.295 0.247 1.27 BSC 0.050 BSC 1.27 BSC 0.050 BSC 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 02/25/03 PACKAGING INFORMATION Plastic STSOP - 32 pins Package Code: H (Type I) A2 A A1 1 N E b e D1 D S SEATING PLANE L α C Plastic STSOP (H - Type I) Millimeters Inches Symbol Min Max Min Max Ref. Std. N 32 A — 1.25 — 0.049 A1 0.05 — 0.002 — A2 0.95 1.05 0.037 0.041 b 0.17 0.23 0.007 0.009 C 0.14 0.16 0.0055 0.0063 D 13.20 13.60 0.520 0.535 D1 11.70 11.90 0.461 0.469 E 7.90 8.10 0.311 0.319 e 0.50 BSC 0.020 BSC L 0.30 0.70 0.012 0.028 S 0.28 Typ. 0.011 Typ. α 0° 5° 0° 5° Notes: 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. Integrated Silicon Solution, Inc. PK13197H32 Rev. B 04/21/03 PACKAGING INFORMATION Mini Ball Grid Array Package Code: B (36-pin) Top View 1 2 3 4 56 6 Bottom View φ b (36x) 5 4 3 2 1 A B C D D E F G H D1 e A B C D E F G H e E E1 Notes: 1. Controlling dimensions are in millimeters. A2 SEATING PLANE A1 A mBGA - 6mm x 8mm MILLIMETERS Sym. N0. Leads A A1 A2 D D1 E E1 e b 5.90 — 0.24 0.60 7.90 mBGA - 8mm x 10mm INCHES Min. Typ. Max. 36 MILLIMETER Sym. N0. Leads INCHES Min. Typ. Max. 36 Min. Typ. Max. 36 — — — 8.00 5.25BSC 6.00 6.10 3.75BSC 0.75BSC 0.30 0.35 0.40 1.20 0.30 — 8.10 Min. Typ. Max. 36 — 0.24 0.60 — — — 5.25BSC 7.90 8.00 8.10 3.75BSC 0.75BSC 0.30 0.35 0.40 1.20 0.30 — — 0.009 0.024 — — — 0.047 0.012 — A A1 A2 D D1 E E1 e b — 0.009 0.024 — — — 0.047 0.012 — 0.311 0.315 0.319 0.207BSC 0.232 0.236 0.240 0.148BSC 0.030BSC 0.012 0.014 0.016 9.90 10.00 10.10 0.390 0.394 0.398 .207BSC 0.311 0.315 0.319 0.148BSC 0.030BSC 0.012 0.014 0.016 Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. E 01/15/03 PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) N N/2+1 E1 E Notes: 1. Controlling dimension: millimieters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. 1 D N/2 SEATING PLANE ZD A . e b L A1 α C Symbol Ref. Std. No. Leads A A1 b C D E1 E e L ZD α Millimeters Min Max Inches Min Max Plastic TSOP (T - Type II) Millimeters Inches Min Max Min Max 44 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.45 0.012 0.018 0.12 0.21 0.005 0.008 18.31 18.52 0.721 0.729 10.03 10.29 0.395 0.405 11.56 11.96 0.455 0.471 0.80 BSC 0.032 BSC 0.41 0.60 0.016 0.024 0.81 REF 0.032 REF 0° 5° 0° 5° Millimeters Min Max 50 — 1.20 0.05 0.15 0.30 0.45 0.12 0.21 20.82 21.08 10.03 10.29 11.56 11.96 0.80 BSC 0.40 0.60 0.88 REF 0° 5° Inches Min Max (N) 32 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.52 0.012 0.020 0.12 0.21 0.005 0.008 20.82 21.08 0.820 0.830 10.03 10.29 0.391 0.400 11.56 11.96 0.451 0.466 1.27 BSC 0.050 BSC 0.40 0.60 0.016 0.024 0.95 REF 0.037 REF 0° 5° 0° 5° — 0.047 0.002 0.006 0.012 0.018 0.005 0.008 0.820 0.830 0.395 0.405 0.455 0.471 0.031 BSC 0.016 0.024 0.035 REF 0° 5° Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 06/18/03