N155.123BX01

Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Features – Target display for manual format aligning – Display: LCD backlit, two lines – One key permanently assigned as target – Interface RS485 N 155 with connector output Technical data - electrical ratings Voltage supply Current consumption Display Display range Interface Data memory Programmable parameters Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 24 VDC ±10 % ≤30 mA LCD, 7-segment display, 2-lines, backlit -9999...+99999 RS485 (ASCII protocol) >10 years in EEPROM Measuring unit mm/inch Direction arrows Decimal point Overvoltage category II Protection class II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Operation / keypad Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity E-connection IP 65 -10...+50 °C -20...+70 °C 80 % non-condensing - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M16, 5-pin Membrane with one softkey (handshake) Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 Surface mount housing with mounting plate 37 x 75 x 29 mm Mount onto plate 60 g Polyamide black, UL 94V-0 1 www.baumerivo.com www.baumerivo.com Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 Target Displays N 155 Part number N 155. 1 3 B X01 Description The multicon spindle positioning system is completed by a target display indicating also positions of hand wheels, limits, linear units etc in close vicinity of the actuator. The backlit LCD display provides the editing engineer with the target parameters. The handshake key is saving the edited parameters. Serial interface RS485 enables network of maximum 32 target and spindle position displays with PC or PLC. For complete solutions also memory controllers as decentralized operating and memory terminals are available. Display B Horizontal at front Voltage supply 3 24 VDC E-connection 0 Connector output M8 with male and female connector 1 Bottom cable output M8 2 Rear cable output M8 3 Bottom cable output M16 Interface 1 RS485 Accessories Connectors and cables (page %S) Z 178.A01 Z 178.AW1 Z 178.B01 Z 178.D05 Z 178.S01 Z 178.V01 Adaptor cable between cable connector M8 and female M16, 1 m Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Mating connector M8, 4-pin, less cable Data and supply cable M8, Master to N 150 and N 155, 5 m Cable connector M8, 4-pin, less cable Coupling cable 1 m between M8 and M8 2 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Target Displays Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 N 155 Terminal assignment M8 connector Pin 1 Pin 2 Pin 3 Pin 4 M16 connector Assignment Pin 5 Pin 4 Pin 1 Pin 2 M8 connector 1 3 2 4 2 4 1 3 Tx/Rx-, RS485 Tx/Rx+, RS485 Sensor supply +24 V Sensor supply 0 V M8 female connector M16 connector 4 3 2 1 1 5 2 3 4 M16 female connector 5 3 www.baumerivo.com www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Plug-on mount, enter key, manual format alignment Display LCD two lines, interface RS485 Target Displays N 155 Dimensions Connector male and female 37 29 4.3 Cable output rear, M8 11 36.5 ±0.18 8 75 PG gland with connector 16 PG gland with female connector Cutout for rear cable output 16 M 14 15 36.5 ±0.1 4 Connector Female 16 connector 30 Bottom cable output, M8 and M16 10 14 16 150 Female connector M8 300 Subject to modification in technic and design. Errors and omissions excepted. 10 150 Female connector M1 6 300 Connector M8 Connector M1 6 R5 19 13 12.5 4 www.baumerivo.com 30/10/2008