APT3216CGCK

3.2mmx1.6mm SMD CHIP LED LAMP Part Number: APT3216CGCK Features Green Description 3.2mmx1.6mm SMT LED, 0.75mm thickness. The Green source color devices are made with AlGaInP on Low power consumption. GaAs substrate Light Emitting Diode. Wide viewing angle. Ideal for backlight and indicator. Package : 2000pcs / reel. Moisture sensitivity level : level 3. RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAA6058 REV NO: V.14B DATE: MAY/07/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203001909 Selection Guide Part No. Dice Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. APT3216CGCK Green (AlGaInP) Typ. 2θ1/2 20 50 120° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 nm IF=20mA Green 570 nm IF=20mA Spectral Line Half-width Green 20 nm IF=20mA C Capacitance Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 2.1 2.5 V IF=20mA IR Reverse Current Green 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAA6058 REV NO: V.14B DATE: MAY/07/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203001909 Green APT3216CGCK SPEC NO: DSAA6058 REV NO: V.14B DATE: MAY/07/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203001909 APT3216CGCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) Tel 13751197819 SPEC NO: DSAA6058 REV NO: V.14B DATE: MAY/07/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203001909 PACKING & LABEL SPECIFICATIONS APT3216CGCK Tel 13751197819 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAA6058 REV NO: V.14B DATE: MAY/07/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.T.Liu ERP: 1203001909