SLN3TTED20L0J

KOA SPEER ELECTRONICS, INC. SS-199 R18 AHA 5/01/08 Current Sensing Chip Resistors Type SL/TSL Resistor CERTIFIED CERTIFIED 1. Scope This specification applies to current sensing chip resistors (SL/TSL) produced by KOA Corporation. Products with lead-free terminations meet EU-RoHS requirements. Pb located in glass material, electrode and resistor element is exempt per Annex 1, exemption 5 of EU directive 2005/95/EC 2. Type Designation The type designation shall be in the following form: New Type SL Type SL SLN TSL 1 Size 1 Watt 2 Watt 3 Watt Termination Material T Packaging TE Nominal Resistance ±5%: 2 significant figures + 1 multiplier “R” indicates decimal on value 360 mΩ 2 Flameproof Molded Epoxy Case with UL94V-0 Flammability Rating 3 End Termination with Tin/Lead Solder Plating .248±.012 .122±.008 .075±.008 .094±.008 .047±.012 .047±.012 (6.3±0.3) (3.1±0.2) (1.9±0.2) (2.4±0.2) (1.2±0.3) (1.2±0.3) .453±.012 .276±.008 .098±.008 .197±.008 .067±.02 (11.5±0.3) (7.0±0.2) (2.5±0.2) (5.0±0.2) (1.7±0.5) .453±.012 (11.5±0.3) .453±.012 (11.5±0.3) .276±.008 (7.0±0.2) .276±.008 (7.0±0.2) .094±.008 (2.4±0.2) .098±.008 (2.5±0.2) .217±.008 (5.5±0.2) .197±.008 (5.0±0.2) .063±.008 (1.6±0.2) .067±.02 (1.7±0.5) .102±.02 (2.6±0.5) .100±.016 (2.55±0.4) .102±.02 (2.6±0.5) .248±.012 .122±.008 .039±.008 .094±.008 .028±.008 .047±.012 (6.3±0.3) (3.1±0.2) (1.0±0.2) (2.4±0.2) (0.7±0.2) (1.2±0.3) 5. Rating 100 80 % Rated Power 60 50 40 20 0 -55 Derating Curve Surface Temperature Rise TSL1/SLN2 150 1 25 Temperature Rise (°C) 100 75 50 25 TSL1 (2) SLN2 (1) TSL1 (1) SLN2 (2) SL1/SL2 200 175 Temperature Rise (°C) 150 2 SL2 (2) 125 2 100 75 50 25 SL1 (2) SL2 (1) SL1 (1) 0 70 Ambient Temperature (∞C) 125 180 0 0 25 50 75 100 0 2 0 1 25 50 75 100 % Rated Power % Rated Power 5-1 Rating SL3 For temperature in excess of 110°C, the load shall be derated in accordance with the following figure. 100 80 60 40 20 0 -55 0 110 125 Ambient Temperature (∞C) I Resistors shall have a rated direct-current (DC) continuous working voltage or approximate sine-wave root-meansquare (RMS) alternating-current (AC) continuous working voltage at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula: Where: E = Rated voltage (V) P = Rated power (W) R = Nominal resistance (Ω) I 5-2 Voltage Rating E=√PxR 180 PAGE 2 OF 6 I Bolivar Drive I P.O. Box 547 Bradford, PA 16701 I USA I 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-199 R18 6. Characteristics 6-4 High Frequency Characteristics 6-1 Electrical Characteristics No. 1 2 Item Resistance Temperature coefficient of resistance 1W 2W 3W 3 4 Short time overload Intermittent overload Requirement Within specified tolerance ±180: R=15 mΩ ±180: R=11 mΩ ±180: R=11 mΩ ± 1.0% maximum ± 5.0% maximum Test Method (JIS C 5202) JIS C 5202 5.1 Measured at 25°C JIS C 5202 5.2 + 25°C / +125°C 5* times rated power for 5 seconds 10 Watts (SL3 only) Rated voltage x 3.0* 1 sec. ON/25 seconds OFF 1,000 cycles 18 Watts 1 second ON/125 seconds OFF 1,000 cycles (SL3 only) Surface center to terminations D. C 500V 5 Insulation Resistance 10,000 MΩ minimum 6 Dielectric Withstanding Voltage ± 0.5% maximum No short, burning or arcing A. C 500V 60 sec. * Since temperature rise of this product are affected by the circuit board size, materials, peripheral heat-producing components, etc. check that the solder fillet part temperature after mounting is less than the solder melting point (180°C) in operating condition and that the package surface is 200°C or less. Also, please install radiating patterns and carefully design the pattern width with respect to the load current so that the above temperatures can be maintained. PAGE 3 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-199 R18 6-2 Mechanical Characteristics No. 1 2 Item Resistance to Soldering Heat Solderability Requirement ± 1.0% maximum 95% of the terminal should be covered with new solder ± 0.5% maximum No visual and mechanical damage Test Method (JIS C 5202) MIL-R55342 π 4.7.7, 260°C for 10 seconds Immerse in solder at 230°C ± 5°C for 3 ± 0.5 seconds 6.3 6.9 Condition A Each direction/2 hours 3 4 Vibration Resistance to Solvents 6-3 Environmental Characteristics No. 1 2 3 4 Item Damp Heat Moisture Resistance Load Life (Rated load) Temperature Cycling Flammability Requirement ± 2.0% maximum No visual damage ± 2.0% maximum No evidence of damage ± 2.0% maximum No visual damage ± 1.0% maximum No mechanical damage Incombustible Dimensions in inches (mm) Test Method (JIS C 5202) 7.9 40°C ± 2°C; 90 ~ 95% RH; 1,000 hours MIL-STD-202, Method 103, 40°C, 90-95% RH, 1000 hours MIL-STD-202, Method 108, 70°C, 1000 hours @ RCWV, 1.5 hr ON, 0.5 hr OFF 30 minutes @ -55°C, 15 minutes @ +25°C, 30 minutes @ +125°C, 15 minutes @ +25°C, 5 cycles 7.12 3.1 in flame/out flame Outer 15 sec./15 sec. flame 5 cycles 4.99 (127) .374 (9.5) 5 45∞ Inner flame 1.49 (38) PAGE 4 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-199 R18 7. Taping 7-1 Dimensions of Carrier Tape .069 (1.75) D B1 B2 A2 A1 A1 TSL SL-1 SL-2 SL-3 SLN-2 .134 (3.4±0.1) .142 (3.6±0.1) .303 (7.7±0.1) .303 (7.7±0.1) .303 (7.7±0.1) A2 B1 .157 (4.0) .079 (2.0) J .012 (0.3 øMax.) T1 C F B2 Q K2 T2 K1 Dimensions in inches (mm) J K1 K2 Q T1 T2 C D F .125 .260 (3.2±0.1) (6.6±0.1) .134 .267 (3.4±0.1) (6.8±0.1) .244 .472 (6.2±0.1) (12.0±0.2) .252 .472 (6.4±0.1) (12.0±0.2) .216 .157 (5.5±0.1) (4.0±0.1) .216 .315 (5.5±0.1) (8.0±0.1) .059 .051 .043 .059 .010 .008 (1.5± 0..1) (1.3±0.1) (1.1 ± 0.1) (1.5± 0..1) (0.25±0.05) (0.20±0.05) 00 00 .059 .092 .085 .059 .010 .008 (1.5± 0..1) (2.35±0.1) (2.15±0.1) (1.5± 0..1) (0.25±0.05) (0.20±0.05) 00 00 .291 .480 .469 .945 .452 .472 .059 .134 .126 .081 .010 .008 (7.4±0.1) (12.2±0.1) (11.9±0.1) (24.0±0.2) (11.5±0.1) (12.0±0.1) (1.55± 0..5) (3.4±0.1) (3.2±0.1) (2.05± 0..5) (0.25±0.05) (0.20±0.05) 05 05 .291 .480 .469 .945 .452 .472 .059 .122 .110 .059 .016 .012 (7.4±0.1) (12.2±0.1) (11.9±0.1) (24.0±0.2) (11.5±0.1) (12.0±0.1) (1.5± 0..1) (3.1±0.1) (2.8±0.1) (1.5± 0..1) (0.40±0.05) (0.30±0.05) 00 00 –– .480 (12.2±0.1) –– .472 (12.0±0.1) –– .472 (12.0±0.2) –– .122 (3.1±0.1) –– –– –– –– 7-2 Taped Configuration End tape (Empty) Leader tape (Top tape) (Empty) Dimensions in inches (mm) 1.57 (40) min. 3.15 (80) min. 5.90 (150) min. PAGE 5 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-199 R18 øA 7-3 Reel Dimensions W1 øc E ød øB W2 Dimensions in inches (mm) TSL SL-1 SL-2 SL-3 Qty/ øA øB øC øD E W1 W2 Reel 7.08 2.36 .511 .826 .079 .511 .606 (180 ± 0..0) (60 ± 1..0) (13.0 ± 0.2) (21.0 ± 0.8) (2.0 ± 0.2) (13.0 ± 0.3) (15.4 ± 1.0) 3,000 30 00 7.08 2.36 .511 .826 .079 .511 .606 (180 ± 0..0) (60 ± 1..0) (13.0 ± 0.2) (21.0 ± 0.8) (2.0 ± 0.2) (13.0 ± 0.3) (15.4 ± 1.0) 1,000 30 00 10.0 3.15 .511 .984 .079 1.00 1.18 (255 ± 0..0) (80 ± 1..0) (13.0 ± 0.2) (25.0 ± 1.0) (2.0 ± 0.5) (25.5 ± 2.0) (30.0 ± 1.0) 1,000 30 00 8. Recommended Land Pattern TSL1, SL1 & SL2 Land Solder mask D E Dimensions in inches (mm) D .133 (3.4) .133 (3.4) .213 (5.4) .213 (5.4) .197 (5.0) E .315 (8.0) .315 (8.0) .591 (15.0) .591 (15.0) .591 (15.0) F .118 (3.0) .118 (3.0) .157 (4.0) .157 (4.0) .197 (5.0) F 8-1 Body and Marking Body color Marking color Marking items Black White Resistance value and tolerance TSL1 SL1 SL2 SL3 SLN-2 PAGE 6 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.