KK74VHC240

TECHNICAL DATA Octal Buffer/Line driver, INV (3-State) KK74VHC240 is high-speed logic IC made by CMOS technology and designed for use in high-performance calculating systems with a wide supply voltage range. As for operation speed, KK74VHC240 can be compared with equivalent bipolar ICs based on Schottky TTL and two times surpasses ICs of KK74НС series. KK74VHC240 tolerates operation under conditions when voltage on input is exceeded up to 7V without affecting characteristics and IC reliability. This possibility allows to use KK74VHC240 in radio-electronic devices for interfacing with supply voltages 5V and 3V, eliminate IC failure under supply voltage source emergency outage. Use of output edge shaping block in the microcircuit allows to reduce noise amplitude of noises when switching outputs into the same state simultaneously. Input and output levels of KK74VHC240 are compatible with CMOS levels KK74VHC240 ORDERING INFORMATION KK74VHC240N Plastic KK74VHC240DW SOIC TA = -40° to 85° C for all packages Features: • • • • • • • • • • . Supply voltage range 2.0 to 5.5 V. Output current 8 mA. Low consumption current: 0.2 mkA (typical value) at Та = 25 °С. Latchup current not less than 300 mA at Та = 85 °С. Tolerable value of static potential not less than 2000 V as per human body model (HBM) and not less than 200 V as per machine model (ММ). Ambient operation temperature minus 40 to plus 85 °С. Balanced signal propagation delay. Ensures voltage exceeding mode on input Low noise level at the simultaneous switching of outputs in the same state: VOLP = 0.8 V (max). For pins and functions, compatible with KK74HC240. 1 KK74VHC240 KK74VHC240 truth table Input Output G A L H X L L H Y H L Z Note – H - high voltage level; L – low voltage level; X - any voltage level (low or high); Z - output in the third Pins description in KK74VHC240 Pinout Pin No. 01 20 19 18 17 16 15 14 13 12 11 Symbol 1G 1A1 Description Output enable input Data input Inverse data output Data input Inverse data output Data input Inverse data output Data input Inverse data output Common output Data input Inverse data output Data input Inverse data output Data input Inverse data output Data input Inverse data output Output enable input Supply output from voltage source 1G 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND 01 02 03 04 05 06 07 08 09 10 VCC 2G 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND 2A1 1Y4 2A2 1Y3 2A3 1Y2 2A4 1Y1 2G VCC 2 KK74VHC240 Absolute maximum conditions* Parameter, unit Supply voltage, V Input voltage, V Output voltage, V Input diode current, mA Current of common output and supply output, mA Output current, mA Output diode current, mA Dissipated power, mW Symbol min VCC Vin Vout Iik Icc Iout Iok Pd -0.5 -0.5 -0.5 – – – – – Value max 7.0 7.0 Vcc+0.5V -20 ± 75 ± 25 ± 20 180 *Under absolute maximum conditions operation of microcircuit is not guaranteed. Operation is guaranteed under maximum conditions Maximum conditions Parameter, unit Symbol min Supply voltage, V Input voltage,V Output voltage, V Output current, mA Input rise and fall time, ns/V at Vcc = (3.3 ± 0.3) V at Vcc = (5.0 ± 0.5) V VCC Vin Vout Iout tLH, tHL 2.0 0 0 – 0 0 Value max 5.5 VCC VCC ± 8.0 100 20 3 KK74VHC240 DC electrical characteristics Value Symbo l VIH Parameter High input voltage Test conditions – VCC, V 2.0 25 ° C min 1.5 max – – 0.5 0.3Vcc – – – – – – 0.09 0.09 0.09 0.09 0.36 0.36 ±0.25 ±0.1 4.0 –40 to 85 °C min max 1.5 – 0.7Vcc – – 1.9 2.9 4.4 5.4 2.48 3.80 – – – – – – – 0.5 0.3Vcc – – – – – – 0.1 0.1 0.1 0.1 0.44 0.44 ±2.5 ±1.0 40.0 mkA Unit V 3.0-5.5 0.7Vcc VIL Low input voltage – 2.0 3.0-5.5 2.0 3.0 4.5 5.5 3.0 4.5 2.0 3.0 4.5 5.5 – – 1.92 2.92 4.42 5.52 2.58 3.94 – – – – – – - VOH High output voltage VI = VIH or VIL IO = -50 mkA VOL Low output voltage VI = VIH or VIL; IO = -4 mA VI = VIH or VIL; IO = -8 mA VI = VIH orVIL IO = 50 mkA IOZ II ICC VI = VIH or VIL 3.0 IO = 4 mA VI = VIH or VIL 4.5 IO = 8 mA Output current in VI = VIH or VIL 5.5 VO = VCC or 0V "off" state Input current VI = 5.5V or 0V 0 – 5.5 Consumption current VI =VCC or 0V 5.5 4 KK74VHC240 AC electrical characteristics (tLH = tHL = 3.0 ns) Symbol tPHL, tPLH Parameter Test conditi VCC, V ons Value CL, pF 15 50 15 50 50 50 15 50 15 50 50 50 –40 to 85 °C min max min max – 7.5 – 9.0 – 11.0 – 12.5 – 5.5 – 6.5 – 7.5 – 8.5 – 14.0 – 16.0 25 ° C – – – – – – – 9.2 10.6 14.1 7.3 9.3 1.5 1.0 – – – – – – – 10.5 12.5 16.0 8.5 10.5 1.5 1.0 Unit ns Propagation delay time Figure 3.3 ± 0.3 when switching "on", 1 "off" 5.0 ± 0.5 tPHZ , tPLZ Propagation delay time Figure 3.3 ± 0.3 under transition from 2 high , low level into "off" 5.0 ± 0.5 state tPZH , tPZL Propagation delay time Figure under transition from 2 «off» state into high, low level tOSLH, tOSHL Propagation delays – difference between outputs 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.5 ± 0.5 Capacitance characteristics Symbol CI CO CРD Parameter Input capacity Output capacity Dynamic capacity Test conditions VI = 0 V orVCC VCC, V 5.0 5.0 5.0 Value 25 ° C min max 10 12 34 Unit pF pF pF Noise characteristics (CL = 50 pF) Parameter Symbol VOLP VOLV VIHD VILD VCC, V Positive noise of low output voltage 5.0 Negative noise of low output 5.0 voltage Input dynamic high voltage Input dynamic low voltage 5.0 5.0 min -0.9 3.5 Value max 0.9 1.5 Unit V 5 KK74VHC240 - Time diagram of input and output pulses tLH 0.9 A 0.1 tPHL 0. 5 0.5 0.1 tPLH VCC 0.5 0. 5 0V GND tHL 0.9 VCC Y Fig. 1 tHL G 0.9 0.5 0.1 tPZH Y 0.5 0.1 tLH 0.9 0.5 VCC 0V 0.9 tPHZ 0V VCC VOH tPLZ Y 0.5 tPZL Fig.2 0.1 VOL 6 KK74VHC240 N S UFFIX PLAS TIC DIP (MS - 0 0 1 AD) A Dimens ion, mm 20 11 B 1 10 Symbol A B C MIN 24.89 6.1 MAX 26.92 7.11 5.33 F L D F 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.2 0.38 0.56 1.78 C -T- SEATING N G D 0.25 (0.010) M T K PLAN E G H H J M J K L M N 10° 3.81 8.26 0.36 NOTES : 1. Dimen s io n s “A ”, “B” d o n o t in clu d e mo ld flas h o r p ro tru s io n s . Maximu m mo ld flas h o r p ro tru s io n s 0.25 mm (0.010) p er s id e. D S UFFIX S OIC (MS - 0 1 3 AC) A 20 11 Dimens ion, mm Symbol MIN 12.6 7.4 2.35 0.33 0.4 1.27 9.53 0° 0.1 0.23 10 0.25 8° 0.3 0.32 10.65 0.75 MAX 13 7.6 2.65 0.51 1.27 H B P A B 1 G 10 C R x 45 C D F -TD 0.25 (0.010) M T C M K SE AT IN G PL AN E J F M G H J K M P R NOTES : 1. Dimen s io ns A an d B d o n o t in clud e mo ld flas h o r p ro tru s ion . 2. M aximu m mo ld flas h o r p ro tru s io n 0.15 mm (0.006) p er s id e fo r A ; fo r B ‑ 0.25 mm (0.010) p er s id e. 7