DDRCT-PCI-O4-N1

ispLever CORE TM Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide June 2004 ipug12_03 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Introduction DDR (Double Data Rate) SDRAM was introduced as a replacement for SDRAM memory running at bus speeds over 75MHz. DDR SDRAM is similar in function to regular SDRAM but doubles the bandwidth of the memory by transferring data twice per cycle (on both edges of the clock signal), implementing burst mode data transfer. The DDR SDRAM Controller is a parameterized core. This allows the user to modify the data widths, burst transfer rates, and CAS latency settings of the design. In addition, the DDR core supports intelligent bank management. By maintaining a database of “all banks activated” and the “rows activated” in each bank, the DDR SDRAM Controller decides if an active or pre-charge command is needed. This effectively reduces the latency of read/write commands issued to the DDR SDRAM. Since the DDR SDRAM Controller takes care of activating/pre-charging the banks, the user can simply issue simple read/write commands without regard to the bank/charge status. Features • Performance of Greater than 100MHz (200 DDR) • Interfaces to JEDEC Standard DDR SDRAMs • Supports DDR SDRAM Data Widths of 16, 32 and 64 Bits • Supports up to 8 External Memory Banks • Programmable Burst Lengths of 2, 4, or 8 • Programmable CAS Latency of 1.5, 2.0, 2.5 or 3.0 • Byte-level Writing Supported • Increased Throughput Using Command Pipelining and Bank Management • Supports Power-down and Self Refresh Modes • Automatic Initialization • Automatic Refresh During Normal and Power-down Modes • Timing and Settings Parameters Implemented as Programmable Registers • Bus Interfaces to PCI Target, PowerPC and AMBA (AHB) Buses Available • Complete Synchronous Implementation 2 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 1. DDR Controller Block Diagram DDR SDRAM Interface Bus User Interface Bus Address/2 Cmd Address Command Execution Engine Busy Control Chip Select PCI, PowerPC, AHB or Generic Bus Cmd Generic I/F Block Address system clock On-chip PLL Initialization Control Logic clk clk2x Data_in Valid Data/2 Data_in Data Bus Interface Block Data_out Valid Data_out Data Mask Data Strobe Functional Description The DDR SDRAM Controller block diagram, illustrated in Figure 1, consists of four functional modules: the Generic Interface block, Command Execution Engine, Data Bus Interface block and the Initialization Control Logic. Generic Interface Block The Generic interface block contains the configuration registers: CFG0, CFG1, CFG2, and CFG3. These registers are updated when a Load_CFG command is received from the user. These registers contain the programmable DDR SDRAM timing parameters and can be changed by the user to suit the DDR SDRAM memory timings being used thus giving the flexibility to use any DDR SDRAM memory. Command Execution Engine The command execution engine is the main component of the DDR SDRAM controller. This block accepts commands from the “User Interface Bus” and keeps a record of bank open/close status. It accepts up to two commands at any time (pipelined). Once a command is received, it decides whether to open the bank, close the bank or directly execute the READ/WRITE commands and apply the appropriate DDR SDRAM commands to the DDR SDRAM Memory. Table 1 shows the different user interface commands supported. To maintain throughput of data this block uses two state machines to process READ/WRITE commands received from the user interface. When the commands are continuously received, one state machine works in master mode and the other state machine works in slave mode. The state machine that receives the command first becomes the master and the other becomes the slave on receiving the second command. Once the master state machine completes the command execution, the slave state machine execution is enabled. This block also maintains an auto refresh counter, which refreshes the DDR SDRAM memory at the predetermined programmed intervals even during power down. 3 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Table 1. DDR SDRAM Controller Generic I/F Commands Command Name Cmd[2:0] Description NOP 000 No operation. READ 001 Initiate a burst read. WRITE 010 Initiate a burst write. LOAD CONFIG REG (Load_CFG) 011 Load controller configuration values. The controller uses this command to load the CFG0/CFG1/CFG2/CFG3 registers. LOAD MODE REG (Load_MR) 100 Load the Mode and Extended Mode registers. POWER DOWN 101 Put the DDR SDRAM into power-down or wake up from POWER DOWN. SELF REFRESH 110 To enter into self refresh mode or get out of self refresh mode Data Bus Interface The Data Bus Interface block controls the data flow between the User Interface bus and DDR SDRAM Memory interface bus. The data received from the Memory during a read operation is converted from a double data rate to single data rate; similarly the data to be written into the memory is converted from a single data rate to a double data rate. During a write operation, depending on the data mask signals, the data is written or masked by the DDR SDRAMmemory. Initialization Control Logic When the User sets the initialization bit (Bit 7 in the configuration register CFG0) using the Load_CFG command, this block starts initialization as specified in the DDR SDRAM specification. The DDR controller initialization can only be performed after the system power is applied and the clock is running for at least 200 µs. An initialization is required before any read/write command is issued to the DDR SDRAM memory. User Interface Bus In order to connect this controller to different bus standards Lattice provides the following “Bus Interface blocks”: 1. 2. 3. 4. PCI Target Interface Power PC Interface AMBA-AHB Interface Generic Bus Interface The main function of these “Bus Interface blocks” is to trap all transactions on the respective bus addressed to the DDR SDRAM and translate them into Generic Interface commands. Since all the buses have burst addressing which is greater than the burst supported by the DDR SDRAM memory, all the interfaces have an address generator block which generates the appropriate address depending on the requested burst. In all the interfaces the data going in and out of the bus is stored in a sync FIFO block, which is used as a storage buffer for read/write commands. During a read from the DDR SDRAM the data is sent to FIFO and is read by Bus Interface block. During a write the data is first written into the FIFO before actually writing this data into the DDR SDRAM. PCI Target Interface Block The PCI Target Interface Block is used to interface the Lattice DDR Controller IP core with a Lattice PCI Target core, which simplifies the usage in a PCI Bus environment. Figure 2 shows the system with a PCI Target core. The following are the features of the PCI Target interface block: 4 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor • Parameterized data path width of 32- or 64-bit on the PCI Local Bus and the User interface bus of DDR controller. • Read/Write of configurable registers through PCI memory space. • Read/Write to DDR through PCI memory space. • Supports Power down and self refresh commands for low power applications. • Programmable burst length. • Programmable FIFO Depth • Automatic wake up from power down/self refresh by a Read/Write command. Figure 2. Typical PCI System with Lattice DDR SDRAM Controller Chip Sel 1 BusArbiter PCI Bus PCI BUS MASTER1 Lattice PCI Target IP Core PCI Local Bus (Target Signals) DDR IP Core SDRAM External Bank 1 SDRAM External Bank 0 (e.g. DIMM) DDR SDRAM Memory 0 4Mx8bit Command PCI I/F Block Address Lattice DDR SDRAM Controller Dataout Address/2 Control Datain Chip Sel 0 DDR SDRAM Memory 1 4Mx8bit DDR SDRAM Memory 2 4Mx8bit Data/2 PCI BUS MASTER2 Data Mask Data Strobe DDR SDRAM Memory 3 4Mx8bit PowerPC BUS Interface Block The Power PC Bus Interface block is used to interface with the Lattice DDR SDRAM Controller IP Core with the Power PC 60x Bus. This interface allows easy usage of the Lattice DDR SDRAM Controller in a Power PC Bus environment. Figure 3 shows the system with a Power PC Bus interface block. The following are the features of the Power PC Bus interface block • Supports PowerPC 601,603, 604 and processors supporting 60x bus. • Parameterized data path widths of 32 or 64 bits. • Supports both burst and single-beat data transfers (DDR Burst Length is 4). • Programmable FIFO Depth • Supports pipeline of two requests (write). • Supports Address retry • Supports separate address and data bus tenure. 5 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 3. Typical PowerPC System with Lattice DDR Controller Chip Sel 1 DDR IP Core SDRAM External Bank 1 SDRAM External Bank 0 (e.g. DIMM) DDR SDRAM Memory 0 4Mx8bit Power PC CPU BusArbiter Power PC Bus Command Power PC I/F Block Address Dataout Lattice DDR SDRAM Controller Address/2 Control Datain Chip Sel 0 DDR SDRAM Memory 1 4Mx8bit DDR SDRAM Memory 2 4Mx8bit Data/2 BUS MASTER (DMA Controller) Data Mask Data Strobe DDR SDRAM Memory 3 4Mx8bit AHB Bus Interface Block The AHB Bus Interface Block interfaces between AMBA Bus and Lattice DDR SDRAM Controller IP Core. This interface allows easy usage of the Lattice DDR SDRAM Controller on an ARM AHB bus environment. Figure 4 shows the system with an AHB Bus interface block. The following are the features of the AHB Bus interface block • Parameterized data path widths of 32, 64 and 128 bits on the AMBA Bus and the User Interface Bus. • Supports INCR4/INCR8/INCR16/WRAP4/WRAP8/WRAP16/INCR Bursts (DDR side Burst Length is 4) • Supports Byte/Half word/Word/Double Word transfers (with 64bit AHB-Bus) • Programmable FIFO Depth Figure 4. Typical AHB System with Lattice DDR Controller IP Cores Chip Sel 1 DDR IP Core SDRAM External Bank 1 SDRAM External Bank 0 (e.g. DIMM) DDR SDRAM Memory 0 4Mx8bit ARM Processor DMA Controller (Master) AHB Bus Command AMBA I/F Block Address Dataout Lattice DDR SDRAM Controller Address/2 Control Datain Chip Sel 0 DDR SDRAM Memory 1 4Mx8bit DDR SDRAM Memory 2 4Mx8bit Data/2 AHB Decoder Data Mask Data Strobe 6 DDR SDRAM Memory 3 4Mx8bit Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Parameter Descriptions The static parameters are set before the design is synthesized to a gate-level netlist. The dynamic parameters can also be set in this way, or they can be changed after the core is programmed onto a device by writing the values into the Configuration Registers. The user should consult the DDR SDRAM specifications before choosing the dynamic parameters, which are dependent on the DDR SDRAM device being used. Table 2. Static DDR Core Parameters Parameter Description Default Value Defines the bus width for the data input/output port on the User Interface Bus side of the core. The selectable values are 32, 64, and 128 bits depending on the Interface Type. The data width on the DDR SDRAM Interface Bus (external memory side of the core) will be half of this value. For example, if a 64-bit wide bus is needed to access the DDR memory chip, the value for DSIZE needs to be set to 128. 32 bits RSIZE Defines row address width. 12 bits CSIZE Defines column width. 11 bits BSIZE Defines bank width for internal chip banks. This version of the DDR SDRAM Controller is designed to work with memory chips containing four internal banks (sometimes called a quad memory array). The default value for BSIZE cannot be changed in this version of the core. 2 bits RANK_SIZE Defines the number of external Banks (RANKS). NOTE: an external bank is a memory chip or group of chips (such as on a DIMM) that can be accessed using the same chip select signal. RANK_SIZE = 0 (External Banks = 1) RANK_SIZE = 1 (External Banks = 2) RANK_SIZE = 2 (External Banks = 4) RANK_SIZE = 3 (External Banks = 8) 0 Interface Type The following Bus Interface Blocks are available for connecting this controller to different bus standards: PCI Target Interface, PowerPC Interface, AMBA_AHB Interface, Generic Bus Interface. Generic DSIZE Interface-Dependent Parameters ASIZE_BIM If PCI, AHB or PowerPC Interface Type is selected, this parameter defines the BIM Address space. 32 bits Fifo Depth If PCI, AHB or PowerPC Interface Type is selected, this parameter defines the FIFO Depth. Varies by Interface Type Fifo Add Width If PCI, AHB or PowerPC Interface Type is selected, this parameter defines the FIFO Address Width. Varies by Interface Type Mem Base Address If PowerPC Interface Type is selected, this parameter defines the Memory Base Address on the PowerPC Bus. 0 Mem Size If PowerPC Interface Type is selected, this parameter defines the Memory Size on the PowerPC Bus. 0 Reg Base Address If PowerPC Interface Type is selected, this parameter defines the Register Base Address on the PowerPC Bus. 0 Slave Select Bits If AHB Interface Type is selected, this parameter defines the Slave Select Bits on the AHB Bus. 7 2 bits Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Table 3. Dynamic DDR Core Parameters Parameter Description Default Value INIT Initialize DDR. Initializes the DDR SDRAM when bit is set. Set by command in register. 0 TRCD Delay RAS to CAS Delay. This is the delay from /RAS to /CAS in number of clock cycles and is calculated using this formula INT(tRCD(MIN) / tCK)*. 2 TRRD Delay Row ACTIVE to Row ACTIVE Delay. This delay is in clock cycles and is calculated using this formula INT(tRRD(MIN) / tCK)*. 2 TRFC Delay AUTO REFRESH command period. This delay is in clock cycles and is calculated using this formula INT(tRFC(MIN) / tCK)*. 9 TRP Delay PRECHARGE command period. This is calculated by the formula INT(tRP(MIN) / tCK)*. 2 TMRD Delay LOAD MODE REGISTER command cycle time. This is calculated by the formula INT(tMRD(MIN) /tCK)*. 2 TWR Delay Write recovery time. This is calculated by the formula INT(tWR(MIN) / tCK)*. 2 TRAS Delay ACTIVE to PRECHARGE delay. Defines the delay between the ACTIVE and PRECHARGE commands (maximum value = 15 clock cycles). 6 TWTR Delay WRITE to READ command delay. Defines internal write to read command delay (maximum value = 7 clock cycles). 1 TRC Delay ACTIVE to ACTIVE /AUTOREFRESH command delay. Defines ACTIVE to ACTIVE /auto refresh command period delay (maximum value = 15 clock cycles). 8 CAS Latency CAS Latency. Delay in clock cycles between the registration of a READ command and 2 the first bit of output data. Valid values are 1.5, 2.0, 2.5 and 3.0. (2.0 clock cycles) Burst Length Burst Length. This number determines the maximum number of columns that can be accessed for a given READ/WRITE and is equal to Burst Length programmed in the Mode register. Valid values are 2, 4 and 8. 2 Burst Type Burst Type. Specifies whether an interleaved or sequential burst is required. 0 represents a sequential and 1 represents an interleaved burst type. 0 DSTRENGTH Drive Strength. Defines bit 1 in the Extended mode register. 0 represents normal drive strength, 1 represents a reduced drive strength (required by some memory devices). 0 QFCFUNC Defines bit 2 of the extended mode register which enables or disables the QFC function (required by some memory devices). 0 Refresh Period Refresh Period. Defines maximum time period between AUTOREFRESH commands. Calculate as follows: INT(tREF / tCK)*. 2228 *Notes: tCK = Clock cycle time tRCD(MIN) = ACTIVE to READ or WRITE delay tRRD(MIN) = ACTIVE (bank A) to ACTIVE (bank B) command period tRFC(MIN) = AUTOREFRESH command period (min.) tRP(MIN) = PRECHARGE command period tMRD(MIN) = LOAD_MR command cycle time tWR(MIN) = Write recovery time tREF = AUTOREFRESH command interval (max.) 8 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Signal Descriptions The following tables show the different interface signals for the DDR SDRAM controller. The DDR SDRAM Interface signals are the same for all core configurations. Table 4. DDR SDRAM Interface Bus Signals Direction Active State Description ddr_clk Output N/A DDR SDRAM Clock, derived from the system clock. NOTE: If multiple memory banks are used (RANK_SIZE > 0), then additional clock signals will be needed at the project's top level to drive each individual memory bank. ddr_clk_n Output N/A Inverted DDR SDRAM Clock, derived from the system clock. NOTE: If multiple memory banks are used (RANK_SIZE > 0), then additional clock signals will be needed at the project's top level to drive each individual memory bank. Output High Clock enable. Output N/A Active Low Chip Select. Selects and deselects the DDR SDRAM external bank. ddr_we_n Output Low Write Enable. Defines the part of the command being entered. ddr_cas_n Output Low Column Select. Defines the part of the command being entered. ddr_ras_n Output Low Row select. Defines the part of the command being entered. ddr_ad[RSIZE-1:0] Output N/A Row or column address lines depending whether the /RAS or /CAS is active. ddr_ba[BSIZE-1:0] Output N/A Bank Address Select. Signal Name ddr_cke RANK_SIZE) ddr_cs_n [(2 - 1:0] ddr_dq[DSIZE/2-1:0] In/Out N/A Bi-directional Data Bus. ddr_dqm[DSIZE/16-1:0] Output N/A Data mask signals used to mask the byte lanes for byte level write control. ddr_dqs[DSIZE/16-1:0] In/Out N/A Data strobe signals used by memory to latch the write data. Table 5. User Generic Interface Bus Interface Signals Direction Active State clk Signal Name Input N/A System clock. reset_n Input Low System reset. cmd[2:0] Input N/A Command for controller. datain[DSIZE-1:0] Input N/A Data input. DSIZE is a programmable parameter of 32, 64, or 128. addr[ASIZE-1:0] Input N/A Address for read/write. ASIZE is based on size of memory, which is derived by the following formula: ASIZE = RANK_SIZE + RSIZE + BSIZE + CSIZE. Input N/A Data Mask select. Output High Busy signal indicates the controller will not accept any more commands. dmsel[DSIZE/8-1:0] busy Description dataout[DSIZE-1:0] Output N/A Data out. dataout_valid Output High During a read, this signal indicates when the dataout bus from the controller contains valid data. datain_valid Output High This signal indicates when the user can start sending in data through datain bus during a write. Input N/A This is the doubled clock signal coming from the on-chip PLL. clk2x 9 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Table 6. Power PC Bus Interface Signals Signal Name clk Direction Active State In N/A System Clock. Description In LOW System Reset. Out LOW Address Acknowledge. When asserted, this signal indicates the address phase of the transaction is complete. ppc_addr[0:ASIZE_BIM] In N/A Address Bus. Address received from a bus master after receiving a bus grant. ppc_data_l[0:31] I/O N/A Low Data Bus. ppc_data_h[0:31] I/O N/A High Data Bus. ppc_artry_n In LOW Address Retry. This signal indicates the current cycle is aborted and the bus master will issue a request at a later time. ppc_dbb_n In LOW Data Bus Busy. The bus master that has received a data bus grant issues this signal. This signal indicates the length the data bus will be used for a memory access. ppc_ta_n Out LOW Transfer Acknowledge. This signal indicates the data transfer on the PowerPC bus has been completed. ppc_tbst_n In LOW Transfer Burst. This signal indicates a burst transfer is in progress. ppc_tea_n Out LOW Transfer Error Acknowledge. This signal indicates an error has occurred during a data transfer. ppc_ts_n In LOW Transfer Start. This signal indicates the master has begun a memory bus transaction, and the address and transfer attributes are valid. ppc_tsiz[0:2] In LOW Transfer Size. ppc_tt[0:4] In LOW Transfer Type. clk2x In N/A This the doubled clock signal coming from the on-chip PLL. reset_n ppc_aack_n Table 7. PCI Local Bus Interface Signals Signal Name clk Direction Active In N/A Description PCI System Clock. In LOW Asynchronous PCI Reset. l_data_in[DSIZE-1:0] Out N/A Local Address/Burst Length/Data Input. The address/burst length input is used in master transactions. The data input is used for a master write or for a target read. l_data_out[DSIZE-1:0] In N/A Local data output for a master read or a target write. lt_address_out[ASIZE_BIM1:0] In N/A Local starting address output for target reads and writes. lt_ben_out[DSIZE/8-1:0] In N/A Local target byte enables. reset_n In N/A Local command for target reads and writes. lt_abortn Out LOW Local target abort request. lt_disconnectn Out LOW Local target disconnect or retry. l_interruptn Out LOW Local side interrupt request (multi-function device may need additional IRQ signals). lt_rdyn Out LOW Local target ready to receive data (write) or send data (read). lt_r_nw In HIGH Read/Write# (read/not write). Signals whether the current transaction is a read or write. cache[7:0] In N/A lt_command_out[3:0] Local target controller cache register output. 10 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Table 7. PCI Local Bus Interface Signals (Continued) Direction Active status[5:0] Signal Name In N/A Local target controller status register. Description lt_hdata_xfern In LOW Memory or I/O high DWORD read or write data phase complete. The address counter can be incremented in combination with the lt_ldataxfern. lt_ldata_xfern In LOW Memory or I/O low DWORD read or write data phase complete. The address counter can be incremented in combination with the lt_hdataxfern. exprom_hit In HIGH bar_hit[5:0] In N/A Signals that the current address is within one of the base address register ranges, and access is requested until the current cycle is done (multi-function devices will need an additional set of registers for each function). lt_64bit_transn In LOW Signals the local target that a 64-bit read or write transaction is underway. clk2x In N/A This is the doubled clock signal coming from the on-chip PLL. Expansion ROM register hit. Table 8. AMBA Bus Interface Signals Direction Active State clk In N/A Bus Clock. This clock times all bus transfers. All signal timings are related to the rising edge of clk. reset_n In LOW The bus reset signal is active LOW and is used to reset the system and the bus. This is the only active LOW signal. HADDR[ASIZE_BIM-1:0] In N/A The 32-bit system address bus. HTRANS[1:0] In N/A Transfer type. This indicates the type of the current transfer, which can be NONSEQUENTIAL, SEQUENTIAL, IDLE or BUSY. HWRITE In HIGH Transfer direction. When HIGH, this signal indicates a write transfer. When LOW, it indicates a read transfer. HSIZE[2:0] In N/A Transfer size. Indicates the size of the transfer, which is typically byte (8-bit), half word (16-bit), word (32-bit) or double word (64-bit) for a 64-bit AHB Bus. HBURST[2:0] In N/A Burst type. Indicates if the transfer forms part of a burst. Four, eight and sixteen beat bursts are supported. The burst may be either incremental or wrapping. HWDATA[DSIZE-1:0] In HIGH Write data bus. The write data bus is used to transfer data from the master to the bus slaves during write operations. HSELx In HIGH Slave select. This signal indicates that the current transfer is intended for the slave. This signal is a combinatorial decode of the address bus. HSELregx In HIGH This signal indicates the current transfer is meant for internal registers of the Bus Interface Block. This is valid only when HSELx is asserted. HSELmemx In HIGH This signal indicates the current transfer is meant for DDR memory data. This is valid only when HSELx is asserted. HREADY In HIGH Transfer done. When HIGH, the HREADY signal indicates that a transfer has finished on the bus. HRDATA[DSIZE-1:0] Out N/A Read data bus. The read data bus is used to transfer data from bus slaves to the bus master during read operations. HREADY_out Out HIGH Transfer done. When high, the HREADY_out signal indicates that a transfer has finished on the bus. This signal may be driven LOW to extend a transfer. HRESP[1:0] Out N/A Transfer response. The transfer response provides additional information on the status of a transfer. Four different responses are possible: OKAY, ERROR, RETRY and SPLIT. RETRY and SPLIT are not supported. In N/A This is the doubled clock signal coming from the on-chip PLL. Signal Name clk2x Description 11 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Timing Specifications Figure 5. Generic I/F Timing Diagram Figure 6. Read Followed By Read (Same Bank Same Row) With BL = 2 12 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 7. Read Followed by Read (Same Bank Different Row) With BL = 2 Figure 8. Read Followed by Read (Different Bank Row Open BL = 2) 13 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 9. Read followed by Read (Different Bank Row Open Row Close BL = 2) Figure 10. Read Followed by Read (Different Bank Row Closed BL = 2) 14 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 11. Write Followed by Write (Same Bank Same Row BL = 2) Figure 12. Write Followed by Write (Same Bank Different Row BL = 2) 15 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 13. Write Followed by Write (Different Bank Row Open BL = 2) Figure 14. Write Followed by Write (Different Bank Row Open BL = 2) 16 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 15. Write Followed by Write (Different Bank Row Open Row Close BL = 2) Figure 16. Write Followed by Write (Different Bank Row Open Row Close BL = 2) 17 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Figure 17. Power Down Figure 18. Self Refresh 18 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Command Descriptions and Usage This section describes the commands supported and their usage at the generic interface block. NOP This command is issued when the interface is waiting to issue commands. This command does not perform any operation on the DDR SDRAM. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Absolute Address NOP 000 Rank Number xxxx (Don’t Care) READ This command is issued when a READ is required form a memory location. The address is comprised of rank number and absolute address. The absolute address is formed by the row, bank and column addresses. This read command automatically applies ACTIVATE, READ and PRECHARGE commands to the DDR SDRAM by looking at the bank and row address. Once a READ command is issued, the dataout bus will contain valid read data when the dataout_valid signal is high. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Row, Bank, Column READ 001 Rank Number Absolute Address WRITE This command is issued when a WRITE is required from a memory location. The address is composed of rank number and absolute address. The absolute address is formed by the row, bank and column addresses. The WRITE command automatically applies ACTIVATE, READ and PRECHARGE commands to the DDR SDRAM by looking at the bank and row address. After a WRITE command is issued, the controller accepts the data to be written from the datain bus when the datain_valid signal is high. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Row, Bank, Column WRITE 010 Rank Number Absolute Address SELF REFRESH The SELF REFRESH command is issued to retain the data in the DDR SDRAM. This can be issued even if the rest of the system is powered down. In this mode, the DDR SDRAM retains data without applying an external clock signal. During this command, the address is “don’t care” since all the DDR SDRAM devices enter self-refresh mode. Once the command is given, the DDR Controller enters the self-refresh mode. The DDR Controller will remain in this mode until another SELF REFRESH command is sent. All other user commands are ignored while the DDR Controller is in the self-refresh mode. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Row, Bank, Column SELF REFRESH 110 xxxx xxxx (Don’t Care) 19 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Load_MR The Load_MR command is issued to program either the Mode Register or Extended Mode Register depending on the BA1:BA0 bits in the address. BA1:BA0 = 00 Addresses the Mode Register BA1:BA0 = 01 Addresses the Extended Mode Register Once the Mode register is programmed, the CFG0 register in the controller is also updated Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Addr[‘ASIZE-1:14] Addr[13:12] Addr[11:0] Load_MR 100 xxxx xxxx BA1:BA0 A11:A0 POWER DOWN The POWER DOWN command is issued to make the DDR SDRAM enter power down mode. The Controller automatically wakes up the DDR SDRAM, then puts the DDR SDRAM back into power down mode. Once the command is given, the DDR Controller enters power-down mode. The power-down mode (and the DDR SDRAM) remains in power-down mode until another POWER DOWN command is sent. All other user commands are ignored while the DDR is in power-down mode. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Row, Bank, Column POWER DOWN 101 xxxx xxxx (Don’t Care) Load_CFG The Load_CFG command is used to program the Controller CFG0, CFG1, CFG2 and CFG3 registers. The controller register is selected with the A1:A0 bits in the address as shown in the table below. The Load_CFG command can be used before the initialization of the DDR Controller. A[1:0] Configuration Register Selected 00 CFG0 01 CFG1 10 CFG2 11 CFG3 Once the CFG0 is programmed, the Mode Register in the DDR SDRAM is also updated. Addr[‘ASIZE-1:0] Command Name Cmd[2:0] Rank Addr[‘ASIZE-1:20] Addr[19:2] Addr[1:0] Load_CFG 011 xxxx xxxx A[19:2] A1:A0 The A[19:2] maps to the register (refer to the next section on Configuration Registers). 20 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Configuration Registers There are four Configuration registers in the DDR Controller: CFG0, CFG1, CFG2 and CFG3. These registers are selected using the Load_CFG command (see above). The A1 and A0 address bits determine the CFG register being addressed. A2 to A19 contain the data to be loaded into the selected register. See the description of the Load_CFG command for more information. Configuration Register 0 The Configuration Register 0 (CFG0) is used to modify the DDR SDRAM Controller timing and behavior. Table 9 describes the contents of CFG0. When any change is made to this register, the DDR Controller automatically updates the DDR SDRAM mode register. The DDR SDRAM mode register is also updated when the DDR Controller receives a LOAD MODE REG command. The user can program the Burst Length, Burst Type, and CAS Latency bits or use the default values without any programming. After the power up condition is satisfied (all power supply and reference voltages are stable at approximately 200µs), the user triggers initialization of the DDR SDRAM by setting the INIT bit using the Load_CFG command. Once this bit is set, the controller starts the initialization process. The busy signal is held high until the initialization process is completed. The default values for this register are set in the Verilog parameters file. Table 9. Configuration Register 0 (CFG0) Configuration Bits CFG0[2:0] CFG0[3] CFG0[6:4] CFG0[7] CFG0[19:8] Parameter Burst Length Description Burst Length, valid values are 2, 4 and 8. 001b = 2 010b = 4 011b = 8 All others are reserved. Default value is Burst Length parameter. Burst Type Burst Type, Sequential / Interleaved 0 = Sequential 1 = Interleaved Default value is Burst Type parameter CAS Latency CAS Latency in number of clock cycles. 101b = 1.5 010b = 2.0 110b = 2.5 011b = 3.0 Default value is CAS Latency parameter INIT Reserved Initialize the DDR SDRAM when this bit is set. Default value is 0. These bits are reserved. Default value is unknown. 21 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor Configuration Register 1 The Configuration Register 1 (CFG1) is used to modify the DDR SDRAM Controller timing and behavior. The correct settings will depend on the DDR SDRAM being used with the controller. Table 10 shows the contents of CFG1. Table 10. Configuration Register 1 (CFG1) Configuration Bits Parameter Description CFG1[2:0] TRCD Delay RAS to CAS Delay in number of clocks (maximum value 7 clocks). Default value is TRCD Delay parameter CFG1[5:3] TRRD Delay Active bank A to active bank B command (maximum value 7 clocks). Default value is TRRD Delay parameter CFG1[9:6] TRFC Delay AUTO REFRESH command delay period in number of clocks (maximum value 15 clocks). Default value is TRFC Delay parameter CFG1[12:10] TRP Delay PRECHARGE Command period (maximum value 7 clocks). Default value is TRP Delay parameter CFG1[15:13] TMRD Delay LOAD MODE REGISTER Command period (maximum value 7 clocks). Default value is TMRD Delay parameter CFG1[18:16] TWR Delay Write recovery time (maximum value 7 clocks). Default value is TWR Delay parameter CFG1[19] Reserved This bit is reserved. Default value is unknown. Configuration Register 2 The Configuration register 2 (CFG2) contains the 16 bits used to store the Refresh Period (RP). The DDR Controller regularly issues AUTO REFRESH commands to the DDR SDRAM during normal operation mode. Table 11 shows the contents of CFG2. Table 11. Configuration Register 2 (CFG2) Configuration Bits Parameter Description CFG2[15:0] Refresh Period Refresh Period (max. = tCK * FFFFh). Default value is Refresh Period parameter. CFG2[19:16] Reserved These bits are reserved. Default value is unknown. Configuration Register 3 The Configuration register 3 (CFG3) is used to modify the DDR SDRAM Controller timing and behavior. The correct settings will depend on the DDR SDRAM being used with the controller. Table 12 shows the contents of CFG3. Table 12. Configuration Register 3 (CFG3) Configuration Bits Parameter Description CFG3[3:0] Active to pre-charge command (maximum value of 15 clocks). Default value is TRAS TRAS Delay Delay parameter. CFG3[6:4] TWTR Delay Internal write to read command delay (maximum value of 7 clocks). Default value is TWTR Delay parameter. CFG3[10:7] TRC Delay Active to Active/AUTO REFRESH command delay period in number of clocks (maximum value of 15 clocks). Default value is TRC Delay parameter. CFG3[19:11] Reserved These bits are reserved. Default value is unknown. 22 Double Data Rate (DDR) SDRAM Controller (Pipelined Version) User’s Guide Lattice Semiconductor The following procedure is required for the ORCA® Series 4 version of this IP core. For other device versions, refer to the Readme release notes included in that evaluation package. Before going to the Place and Route, the user needs to run edifmod.pl provided in the package to generate a new EDIF netlist. Installation of Perl programming software is required before running the script (edifmod.pl) provided. To download Perl programming software, please visit www.activeperl.com for the latest version of the software. The script (edifmod.pl) will allow user to insert the I/O types property to the specific instances that declare in the port inside the EDIF netlist. The current LeonardoSpectrum synthesis tool only inserts I/O type property on ports and the ispLEVER software requires the I/O type property inserted on the instances. Therefore, the script (edifmod.pl) is provided to work around the problem. Open DOS-shell, change directory to where the EDIF netlist located and type: perl edifmod.pl .edf By running the edifmod.pl provided, it will generate a new EDIF netlist as .edf.new. The new EDIF netlist need to be renamed to .edf before importing the netlist. References • Double Data Rate (DDR) SDRAM Data Sheet, Micron Technology, Inc., 2001. • 128 M-bit Synchronous DRAM with Double Data Rate Data Sheet, NEC Corp., December 1998. • DDR SDRAM Specification Version 0.3, Samsung Electronics, 2000. • DDR SDRAM Controller Data Sheet, Lattice Semiconductor Corporation, 2003. • ispLeverCORE™ Evaluation Tutorials, Lattice Semiconductor Corp., 2003. Technical Support Assistance Hotline: 1-800-LATTICE (North America) +1-408-826-6002 (Outside North America) e-mail: techsupport@latticesemi.com Internet: www.latticesemi.com 23