LVY9033-TR2

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT TYPE AND REEL LVY9033/TR2 DATA SHEET DOC. NO REV. DATE : QW0905-LVY9033/TR2 :A : 09 - Jun - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page 1/8 Package Dimensions Cathode 2.5 0.4±0.1 0.5±0.1 2.0 5.8 ±0.5 ψ1.9 3.05 ±0.5 1.4 2.8 0.7 4.3 ±0.5 Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Carrier Type Dimensions t W1 W F B0 Polarity E Do P2 P Po Ko Cathode Note : The tolerances unless mentioned is ±0.2mm,Angle ± 0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page 2/8 Reel Dimensions 16.0±1.0 ψ178±2.0 14.2±1.0 74.0±1.5 Part No. LVY9033/TR2 Description 12.0mm tape,7"reel Quantity/Reel 1500 devices LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page 3/8 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol VY Forward Current Peak Forward Current Duty 1/10@10KHz Power Dissipation Reverse Current @5V Electrostatic Discharge Operating Temperature Storage Temperature Soldering Temperature IF IFP PD Ir ESD Topr Tstg Tsol 30 60 75 10 2000 -40 ~ +85 -40~ +100 Max 260 ℃ for 5 sec Max mA mA mW UNIT μA V ℃ ℃ Typical Electrical & Optical Characteristics (Ta=25 ℃) Dominant wave length λDnm Spectral halfwidth △λnm PART NO MATERIAL Emitted COLOR Lens Water Clear Forward voltage @20mA(V) Luminous intensity @20mA(mcd) Viewing angle 2θ 1/2 (deg) Min. 590 20 1.7 Max. 2.6 Min. Typ. 220 450 20 LVY9033/TR2 AlGaInP Yellow Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Page4/8 Typical Electro-Optical Characteristics Curve VY CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 1000 3.0 Forward Current(mA) 100 10 Relative Intensity Normalize @20mA 1.0 2.5 2.0 1.5 1.0 0.5 0.0 1.0 10 100 1000 1.0 0.1 1.5 2.0 2.5 3.0 Forward Voltage(V) Fig.3 Forward Voltage vs. Temperature 1.2 Forward Current(mA) Fig.4 Relative Intensity vs. Temperature 3.0 Relative Intensity@20mA Normalize @25 ℃ Forward Voltage@20mA Normalize @25 ℃ 1.1 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 Ambient Temperature( ℃) Ambient Temperature( ℃) Fig.5 Relative Intensity vs. Wavelength 1.0 Relative Intensity@20mA 0.5 0.0 500 550 600 650 Wavelength (nm) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Soldering Iron: Basic spec is ≦5 sec when 260 ℃. If temperature is higher, time should be shorter(+10 ℃ → -1sec). Power dissipation of iron should be smaller than 15W,and temperature should be controllable. Surface temperature of the device should be under 230 ℃. Page 5/8 Soldering heat Soldering heat Max. 260 ℃ 245±5℃ within 5 sec Preheat 120 ~ 150 ℃ 120 ~ 180 sec Reflow Temp/Time Temp. (℃) 220 Rising +5℃/sec Cooling -5℃/sec 150 120 Preheat 60 ~ 120 sec 5sec Time LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃fo r 15hrs. Page 6/8 Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 Reliability Test: Page 7/8 Classification Test Item Test Condition 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) Reference Standard MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 Operating Life Test High Temperature Storage Test Endurance Test Low Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=65 ℃±5℃ 3.RH=90%~95% 4.t=1000hrs ±2hrs 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃±5℃& -40 ℃±5℃ (10min) (10min) 3.total 10 cycles 1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Immersion rate 25 ±2.5mm/sec 4.Immersion rate 25 ±2.5mm/sec 5.Coverage ≧95% of the dipped surface 1.105 ℃ ~ 25℃ ~ 55℃ ~ 25℃ 30mins 5mins 30mins 5mins 2.10 Cyeles MIL-STD-202F:103B JIS C 7021: B-11 Thermal Shock Test MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Solderability Test Temperature Cycling Environmental Test Solderability Test Ramp-up rate(183 ℃ to Peak) +3 ℃ second max Temp. maintain at 125( ±25)℃ 120 seconds max Temp. maintain above 183 ℃ 60-150 seconds Peak temperature range 235 ℃+5-0 ℃ Time within 5℃ of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6 ℃/second max MIL-STD-750D:2031.2 J-STD-020 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LVY9033/TR2 . MAIN RAW MATERIAL LIST Page 8/8 ITEM 1 MATERIAL Yellow Chip (AlGaInP) MODEL ED-M80HYU SUPPLIER 光磊科技股份有限公司 (OPTO TECH CORPORATION ) ORIGIN 台灣 TAIWAN 2 銀膠 (Silver Epoxy) 826-1 ABLESTIK 美國 USA 3 支架 (Lead Frame ) 2005-9 巨貿精密工業股份有限公司 (TTOP CORPORATION ) 台灣 TAIWAN 4 gold wire φ0.1mil Au AMERICAN FINE WIRE 美國 USA 5 Epoxy NT-301H-11000 台灣日東電工股份有限公司 (NITTO DENKO (TAIWAN) CORPORATION ) 台灣 TAIWAN