EQD020A0F641

Data Sheet November 9, 2006 EQD020 Series Single Output: Eighth Brick Through-Hole Power Modules 19 - 60Vdc Input; 3.3Vdc Output; 66W RoHS Compliant Features Compliant to RoHS EU Directive 2002/95/EC (-Z versions Compatible in a Pb-free or SnPb reflow environment (-Z versions) High efficiency – 90% at 48Vin, full load Industry standard Eighth brick footprint and pin out 57.9 mm x 22.8 mm x 8.5 mm (2.28 in. x 0.90 in. x 0.335 in.) > 3:1 Input voltage range: 19 - 60 Vdc Input under/overvoltage protection Output overcurrent/voltage protection Applications Distributed power architectures Wireless Networks Optical and Access Network Equipment Enterprise Networks Over-temperature protection Tightly regulated output Remote sense No reverse current during output shutdown Negative logic, Remote On/Off Output voltage trim ± 10% Wide operating temperature range (-40°C to 85°C) UL* 60950-1Recognized, CSA† C22.2 No. 60950-1‡ 03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Licensed for Basic Insulation rating per EN60950-1 Options Positive logic, Remote On/Off Auto restart after fault protection shutdown Heat plate Case ground pin (with heat plate only) Description The EQD020 series DC-DC converters are a new generation of open-frame DC/DC power modules designed to support a 3:1 input voltage range, that allows operation in both 24V or 48V nominal input voltage systems, thus eliminating the need for separate power modules for each input voltage range. These single output DC-DC converters operate over an input voltage range of 19 to 60 Vdc. The series is also designed to provide a tightly regulated output voltage trim range of ± 10% VO,Set, with output current up to 20A at 3.3Vdc in an industry standard eighth brick package. The output is isolated from the input, allowing versatile polarity configurations and grounding connections. Built in filtering for both input and output minimizes the need for external filtering. * UL is a registered trademark of Underwriters Laboratories, Inc. † ‡ CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS06-115 ver. 1.1 PDF name: eqd020_ds.pdf Data Sheet November 9, 2006 EQD020 Series Single Output: Eighth Brick Power Modules: 19-60 Vdc Input; 3.3Vdc Output; 66W Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Continuous, Operational Transient, Operational (10mS minimum) Transient , Non-operational (100 mS maximum) Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature I/O Isolation Input – Output (100% factory Hi-Pot tested) F F F F F F VIN VIN, trans VIN, trans TA Tstg -40 -55 -0.3 60 75 100 85 125 1500 Vdc Vdc Vdc °C °C Vdc Device Symbol Min Max Unit Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VIN=0 to VIN, max , Vo = Vo,set, IO=IO, max ) Input Stand-by Current Module on / off disabled (VIN = VIN, nom, Vo = 0 V) Input No Load Current Module on / off enabled (VIN = VIN, nom, Io = 0 A) Inrush Transient Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; o Ta 25 C, Cin = 33µF) Input Ripple Rejection (100 - 120Hz) F F F F 50 IIN, NL It 2 Device F F Symbol VIN IIN,max Min 19 Typ 24/48 Max 60 5 Unit Vdc Adc F IIN, Stby 25 mA 110 1 30 mA As mAp-p dB 2 CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a very fast-acting surface mount fuse with a maximum rating of 6.3 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Tyco Electronics Power Systems 2 Data Sheet November 9, 2006 EQD020 Series Single Output: Eighth Brick Power Modules: 19-60Vdc Input; 3.3Vdc Output; 66W Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN = VIN, min=24/48, IO =IO, max, TA =25°C) Output Voltage (Over all line, load, and Temp Conditions until end of life) Output Regulation Line (VIN = VIN, min to VIN, max) Load (IO = IO, min to IO, max) Temperature (Tref =TA, min to TA, max) Output Ripple and Noise on nominal output (VIN =VIN, nom and IO = IO, min to IO, max, Cout = 1μF ceramic // 10μF Tantalum capacitor) RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance ESR ≥ 10 mΩ Output Current Output Current Limit Inception (Hiccup Mode) (Vo = 90% Vo, set ) Output Short-Circuit Current VO ≤ 250 mV @ 25 C Efficiency VIN= 24V, TA=25°C, Vo = 3.3V, IO= IO, max A VIN= 48V, TA=25°C, Vo = 3.3V, IO= IO, max A Switching Frequency Dynamic Load Response (dIo/dt= 1A / 10μs; VIN = VIN, nom; TA=25°C, Output Capacitance = 470 µF Polymer) Load Change from Io= 50% Io,max to (50%± 25%) Io,max or from Io= (50%± 25%) Io,max to 50% Io,max Peak Deviation Settling Time (Vo