DC2293A-B

DEMO MANUAL DC2293A LTC2933 Programming Board for Programmable Hex Voltage Supervisor with EEPROM Description The DC2293A programming board contains the circuitry needed to program and verify the EEPROM of the LTC2933. This is its sole purpose. The LTC®2933 comes in either a 16-pin SSOP or a 16-pin DFN package. The DC2293A-A supports the SSOP and the DC2293A-B supports the DFN package. The LTpowerPlay GUI stores configuration settings into the LTC2933 EEPROM. Download and install the software from this location: http://www.linear.com/ltpowerplay/ Demo System Required Hardware Windows PC USB-to-I2C/SMBus/PMBus Controller (DC1613) nn DC2293A-A or DC2293A-B (LTC2933 component must be ordered separately.) nn nn Demo System Required Software nn LTpowerPlay LTC2933 Features Supervise 6 Power Supplies I2C Adjustable UV and OV Trip Points nn Guaranteed Threshold Accuracy: ±1% (Maximum) nn I2C/SMBus Interface nn Internal EEPROM nn 256 Programmable Thresholds per Channel nn Up to Three Range Settings per Channel nn Two General Purpose Inputs and 3 GPIOs nn Supply Voltage Range: 3.4V to 13.9V nn Supply Voltage Power Sharing from V1 to V4 nn 16-Pin 5mm x 4mm DFN and SSOP Packages nn The DC2293A communicates with LTpowerPlay through a Linear Technology® DC1613 USB to I2C/SMBus/PMBus Controller. What Can You Do with the DC2293A 1. Compare the contents of the device’s EEPROM against any Project File. (Verify) 2. Reprogram the contents of the device’s EEPROM using any Project File. (Program and Verify) nn Design files for this circuit board are available at http://www.linear.com/demo/DC2293A L, LT, LTC, LTM, Linear Technology and the Linear logo, µModule and PolyPhase are registered trademarks and LTpowerPlay is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. USB USB TO I2C/SMBUS/PMBus CONTROLLER (DC1613) RIBBON CABLE LTC2933 PROGRAMMING BOARD (DC2293A) Figure 1. LTC2933 Programming Setup Using DC2293A dc2293af 1 DEMO MANUAL DC2293A Board Photo TOP OF THE SPRING LOADED SOCKET FRAME DC2293A-A 16-LEAD PLASTIC SSOP ORDER OPTION A DC2293A-B 16-LEAD PLASTIC DFN ORDER OPTION B DC1613 CONNECTOR J1 ASEL0 J2 POWER SWITCH S1 USB +5V SCL SDA GND DC2293 F02 Figure 2. DC2293A Top Side Details (DC2293A-A Shown) Order Information There are two versions of the DC2293A. Each version of the programming board comes with only one socket. See table below. ORDER NUMBER SUPPORTED DEVICES DC2293A-A LTC2933 16-Lead Plastic SSOP DC2293A-B LTC2933 16-Pin (5mm × 4mm) Plastic DFN 2 dc2293af DEMO MANUAL DC2293A LTpowerPlay GUI Software LTpowerPlay is a powerful Windows-based development environment that supports Linear Technology Power System Management ICs with EEPROM, including the LTC2933 Programmable Hex Voltage Supervisor. The software supports a variety of different tasks. You can use LTpowerPlay to evaluate Linear Technology ICs by connecting to a demo board system. LTpowerPlay features an offline mode to build a multi-chip configuration file for later use with hardware. LTpowerPlay provides unprecedented system level diagnostic and debug features. It becomes a valuable diagnostic tool during board bring-up to program or tweak the power management scheme in a system or SYSTEM TREE OF ALL DEVICES CONFIGURATION SETTING FOR ALL DEVICES IN SYSTEM TREE to diagnose power issues when bringing up rails. LTpowerPlay utilizes the DC1613 I2C/SMBus/PMBus Controller to communicate with one of many potential targets, including the DC2293A demo system or a customer board. The software also provides an automatic update feature to keep the software current with the latest set of device drivers and documentation. Download the software from: http://www.linear.com/ltpowerplay Select “Help, View Online Help” from the LTpowerPlay menu to access technical documents. REAL TIME TELEMETRY DATA CHIP DASHBOARD (KEY ASPECT OF SELECTED CHIPS) ASEL1 J2 Figure 3. Screenshot of the LTpowerPlay GUI dc2293af 3 DEMO MANUAL DC2293A Quick Start Procedure The DC2293A programming board makes it easy to program and verify the LTC2933 EEPROM contents. 1. Place jumpers and switches in the following default positions: ASEL0: L OFF S1: 3. If using DC2293A-A, open the pinch contacts of the socket by pressing down and holding the top of the spring loaded socket frame. Place the IC inside the socket with pin 1 located in the upper left corner. Slowly release the top of socket frame, allowing contacts to pinch together and grip IC leads. See Figure 5. NOTE: By default, the ASEL0 jumper is set to low. If you wish to program a device with an address other than 0x1C, adjust the ASEL0 jumper appropriately. Consult device data sheet for details. 2. Connect the DC1613 USB controller to your PC. Plug the ribbon cable into connector J1 of the DC2293A programming board. See Figure 4. Figure 5. DC2293A-A and IC Installed Figure 4. DC2293A-A with Open Socket NOTE: Removal and insertion of the IC should be done with either tweezers or a vacuum device, and also with the power switch S1 set to OFF. 4 dc2293af DEMO MANUAL DC2293A Quick Start Procedure 4. If using DC2293A-B, flip open the socket lid and place the IC inside with pin 1 located in the upper left corner. See Figure 6. PIN 1 INDICATOR 5. Set the power switch S1 to the ON position. The VDD33 LED will illuminate, indicating the on-chip regulator is providing internal power. If the LED does not illuminate, check the orientation of the IC in the socket. Pin 1 must be in the upper left corner. 6. Launch the LTpowerPlay software from your PC. The device programming utility shown in Figure 8 should pop up automatically. If it does not, then select the Utilities>Programming Utility from the menu shown in Figure 9. 7. Click “…” next to the selection box and select a .proj file from your system to program the device. See Figure 8. DC2293 F06 Figure 6. DC2293A-B and IC Installed Close the lid. It will snap into place. See Figure 7. Figure 8. Selecting a .proj File to Program Figure 9. Utilities > Programming Utility from the Menu Figure 7. DC2293A-B and IC Installed dc2293af 5 DEMO MANUAL DC2293A Quick Start Procedure 8. Click the “Program and Verify” button (See Figure 10) and wait for the process to complete. After the process is complete, you will see “Successfully Programmed and Verified Device” in the status bar at the bottom. See Figure 11. Figure 11. Programmed and Verified Device 9. Set the power switch S1 to the OFF position prior to removing the device. Figure 10. Device Programming Utility. 6 Repeat steps above to program additional devices. LTpowerPlay’s Programming Utility does not need to be closed. The ribbon cable may remain connected to the programming board. dc2293af 2. ALL CAPACITORS ARE 16V 0603 1 2 3 4 5 6 7 8 9 10 11 12 CONN_DC1613 +5V (100mA) SDA GND SCL +3.3V(100mA) ALRTB GPO_1 OUTEN GPO_2 GND AUXSCL AUXSDA J1 GND GND EESCL Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. SDA GND 3 SDA 2 GND VCC 4 GND GND WP 5 U3 24AA02 1 SCL OPT C9 100nF GND R17 10.0 GND C1 1.0uF 2 5 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 OPT 3 1 6 4 16 15 14 13 12 11 10 9 GND C2 100nF +5V V5 V6 GPI1 GPI2 SCL SDA GPIO1 GPIO2 POWER S1 V4 V3 V2 V1 VDD33 GND GPIO3 ASEL OPT J2 ASEL0 1 2 3 4 U1 LTC2933ENPLAS GND GND 16 15 14 13 12 11 10 9 +3V3 V4 V5 V3 V6 V2 GPI1 V1 GPI2 SCL VDD33 SDA GND GPIO3 GPIO1 ASEL GPIO2 PAD U2 LTC2933_DFN_SOCKET PAD +5V GND R2 10.0K EESDA R1 10.0K GND SCL +5V_DONGLE OPT C7 100nF OPT OPT +3V3 C8 100nF C6 100nF GND +3V3 1K R18 C3 1.0uF OPT GND OPT 1K R16 +3V3 ON GREEN R3 1.30K GND 2 GND 1 1. ALL RESISTORS ARE 1% 0603. OPT GND OPT R11 10K SCALE = NONE APP ENG. PCB DES. GND R8 10K OPT R9 10K OPT GND R7 10K OPT R10 10K OPT GND OPT R6 10K GND R5 10K OPT R4 10K OPT R14 10K OPT OPT R15 10K CUSTOMER NOTICE R13 10K R12 10K OPT +3V3 - B www.linear.com LTC CONFIDENTIAL FOR CUSTOMER USE ONLY XX-XX-XX DEMO MANUAL DC2293A Schematic Diagram dc2293af 7 DEMO MANUAL DC2293A DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 1630 McCarthy Blvd. Milpitas, CA 95035 Copyright © 2004, Linear Technology Corporation 8 dc2293af Linear Technology Corporation LT 0116 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2016