LTM4600HVMP

FEATURES n n n n n n n n n n n n n n n n n LTM4608A Low VIN, 8A DC/DC µModule Regulator with Tracking, Margining, and Frequency Synchronization DESCRIPTION The LTM®4608A is a complete 8A switch mode DC/DC power supply with ±1.75% total output voltage error. Included in the package are the switching controller, power FETs, inductor and all support components. Operating over an input voltage range of 2.7V to 5.5V, the LTM4608A supports an output voltage range of 0.6V to 5V, set by a single external resistor. This high efficiency design delivers up to 8A continuous current (10A peak). Only bulk input and output capacitors are needed to complete the design. The low profile package (2.8mm) enables utilization of unused space on the back side of PC boards for high density point-of-load regulation. The 0.630mm LGA pads with 1.27mm pitch simplify PCB layout by providing standard trace routing and via placement. The high switching frequency and current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. The device supports frequency synchronization, programmable multiphase and/or spread spectrum operation, output voltage tracking for supply rail sequencing and voltage margining. Fault protection features include overvoltage protection, overcurrent protection and thermal shutdown. The power module is offered in a compact and thermally enhanced 9mm × 15mm × 2.8mm surface mount LGA package. The LTM4608A is Pb-free and RoHS compliant. Complete Standalone Power Supply ±1.75% Total DC Output Error (–55°C to 125°C) 2.7V to 5.5V Input Voltage Range 8A DC, 10A Peak Output Current 0.6V Up to 5V Output Output Voltage Tracking and Margining Power Good Tracks Margining Multiphase Operation Parallel Current Sharing Onboard Frequency Synchronization Spread Spectrum Frequency Modulation Overcurrent/Thermal Shutdown Protection Current Mode Control/Fast Transient Response Selectable Burst Mode® Operation Up to 95% Efficiency Output Overvoltage Protection Small, Low Profile 9mm × 15mm × 2.8mm LGA Package (0.630mm Pads) Telecom, Networking and Industrial Equipment Storage Systems Point of Load Regulation APPLICATIONS n n n L, LT, LTC, LTM, Linear Technology, the Linear logo, Burst Mode, µModule and PolyPhase are registered trademarks and LTpowerCAD is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 6580258, 6304066, 6127815, 6498466, 6611131. TYPICAL APPLICATION 2.7V to 5.5V Input to 1.8V Output DC/DC µModule® Regulator CLKIN VIN 2.7V TO 5.5V 10µF CLKIN VOUT 1.8V 100µF 4.87k PGOOD VOUT 4608A TA01a Efficiency vs Load Current 100 95 VIN = 3.3V EFFICIENCY (%) 90 VIN = 5V 85 80 75 70 VOUT FB ITH ITHM MGN VOUT = 1.8V VIN SVIN SW RUN TRACK LTM4608A PLLLPF PGOOD CLKOUT GND SGND 0 2 4 6 LOAD CURRENT (A) 8 10 4608A TA01b 4608afc 1 LTM4608A ABSOLUTE MAXIMUM RATINGS (Note 1) PIN CONFIGURATION A 1 2 CLKIN PHMODE MODE 3 4 5 FB GND B TOP VIEW C D E VIN F G GND RUN SGND SW CLKOUT PLLLPF SVIN ITHM TRACK ITH VIN, SVIN ...................................................... –0.3V to 6V CLKOUT ....................................................... –0.3V to 2V PGOOD, PLLLPF, CLKIN, PHMODE, MODE . –0.3V to VIN ITH, ITHM, RUN, FB, TRACK,MGN, BSEL...... –0.3V to VIN VOUT, SW ...................................... –0.3V to (VIN + 0.3V) Internal Operating Temperature Range (Note 2) .................................................. –55°C to 125°C Storage Temperature Range .................. –55°C to 125°C PGOOD 6 BSEL 7 MGN 8 9 10 11 GND VOUT LGA PACKAGE 68-LEAD (15mm × 9mm × 2.8mm) TJMAX = 125°C, θJA = 25°C/W, θJCbottom = 7°C/W, θJCtop = 50°C/W, WEIGHT = 1.0g ORDER INFORMATION LEAD FREE FINISH LTM4608AEV#PBF LTM4608AIV#PBF LTM4608AMPV#PBF TRAY LTM4608AEV#PBF LTM4608AIV#PBF PART MARKING* PACKAGE DESCRIPTION LTM4608AV LTM4608AV 68-Lead (15mm × 9mm × 2.8mm) LGA 68-Lead (15mm × 9mm × 2.8mm) LGA 68-Lead (15mm × 9mm × 2.8mm) LGA TEMPERATURE RANGE –40°C to 125°C –40°C to 125°C –55°C to 125°C LTM4608AMPV#PBF LTM4608AMPV Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V unless otherwise noted. See Figure 1. SYMBOL VIN(DC) VOUT(DC) PARAMETER Input DC Voltage Output Voltage, Total Variation with Line and Load CIN = 10µF × 1, COUT = 100µF Ceramic, 100µF POSCAP RFB = 6.65k, MODE = 0V , VIN = 2.7V to 5.5V, IOUT = IOUT(DC)MIN to IOUT(DC)MAX (Note 3) SVIN Rising SVIN Falling CONDITIONS l ELECTRICAL CHARACTERISTICS MIN 2.7 TYP MAX 5.5 UNITS V l 1.472 1.464 2.05 1.85 1.49 1.49 2.2 2.0 1.508 1.516 2.35 2.15 V V V V Input Specifications VIN(UVLO) Undervoltage Lockout Threshold 4608afc 2 LTM4608A ELECTRICAL CHARACTERISTICS SYMBOL IQ(VIN) PARAMETER Input Supply Bias Current The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V unless otherwise noted. See Figure 1. CONDITIONS VIN = 3.3V, No Switching, MODE = VIN VIN = 3.3V, No Switching, MODE = 0V VIN = 3.3V, VOUT = 1.5V, Switching Continuous VIN = 5V, No Switching, MODE = VIN VIN = 5V, No Switching, MODE = 0V VIN = 5V, VOUT = 1.5V, Switching Continuous Shutdown, RUN = 0, VIN = 5V MIN TYP 400 1.15 55 450 1.3 75 1 4.5 2.93 MAX UNITS µA mA mA µA mA mA µA A A IS(VIN) Input Supply Current VIN = 3.3V, VOUT = 1.5V, IOUT = 8A VIN = 5V, VOUT = 1.5V, IOUT = 8A Output Specifications IOUT(DC) ∆VOUT(LINE) VOUT ∆VOUT(LOAD) VOUT VOUT(AC) fS fSYNC ∆VOUT(START) tSTART ∆VOUT(LS) tSETTLE IOUT(PK) Output Ripple Voltage Switching Frequency SYNC Capture Range Turn-On Overshoot COUT = 100µF VOUT = 1.5V, IOUT = 0A , VIN = 3.3V VIN = 5V COUT = 100µF VOUT = 1.5V, VIN = 5V, , IOUT = 1A Resistive Load, Track = VIN, Load Regulation Accuracy VOUT = 1.5V (Note 3) VIN = 3.3V, 5.5V, ILOAD = 0A to 8A VIN = 2.7V, ILOAD = 0A to 5A IOUT = 0A, COUT = 100µF X5R Ceramic, VIN = 5V, VOUT = 1.5V IOUT = 8A, VIN = 5V, VOUT = 1.5V 1.25 0.75 10 10 100 15 l l Output Continuous Current Range VOUT = 1.5V (Note 3) VIN = 3.3V, 5.5V VIN = 2.7V Line Regulation Accuracy VOUT = 1.5V, VIN from 2.7V to 5.5V, IOUT = 0A l 0 0 0.1 8 5 0.25 A A %/V 0.3 0.3 10 1.5 0.75 0.75 % % mVP-P 1.75 2.25 MHz MHz mV mV µs mV Turn-On Time Peak Deviation for Dynamic Load Load: 0% to 50% to 0% of Full Load, COUT = 100µF Ceramic, 100µF POSCAP , VIN = 5V, VOUT = 1.5V Settling Time for Dynamic Load Step Output Current Limit Load: 0% to 50% to 0% of Full Load, VIN = 5V, VOUT = 1.5V, COUT = 100µF COUT = 100µF VIN = 2.7V, VOUT = 1.5V VIN = 3.3V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V IOUT = 0A, VOUT = 1.5V, VIN = 2.7V to 5.5V l 10 µs 8 11 13 0.590 0.587 0.596 0.596 90 0.2 0.602 0.606 A A A V V µs µA 1.7 1.5 V V Control Section VFB SS Delay IFB VRUN RUN Pin On/Off Threshold RUN Rising RUN Falling 1.4 1.3 Voltage at FB Pin Internal Soft-Start Delay 1.55 1.4 4608afc 3 LTM4608A ELECTRICAL CHARACTERISTICS SYMBOL TRACK PARAMETER Tracking Threshold (Rising) Tracking Threshold (Falling) Tracking Disable Threshold Resistor Between VOUT and FB Pins PGOOD Range Output Voltage Margining Percentage MGN = VIN, BSEL = 0V MGN = VIN, BSEL = VIN MGN = VIN, BSEL = Float MGN = 0V, BSEL = 0V MGN = 0V, BSEL = VIN MGN = 0V, BSEL = Float 4 9 14 –4 –9 –14 The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 5V unless otherwise noted. See Figure 1. CONDITIONS RUN = VIN RUN = 0V 9.95 MIN TYP 0.57 0.18 VIN – 0.5 10 ±10 5 10 15 –5 –10 –15 6 11 16 –6 –11 –16 10.05 MAX UNITS V V V kΩ % % % % % % % RFBHI ∆VPGOOD %Margining Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4608A is tested under pulsed load conditions such that TJ ≈ TA. The LTM4608AE is guaranteed to meet specifications from 0°C to 125°C internal temperature. Specifications over the –40°C to 125°C internal operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM4608AI is guaranteed over the –40°C to 125°C internal operating temperature range and the LTM4608AMP is tested and guaranteed over the full –55°C to 125°C internal operating temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. Note 3: See output current derating curves for different VIN, VOUT and TA. 4608afc 4 LTM4608A TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current 100 95 EFFICIENCY (%) EFFICIENCY (%) 90 85 80 75 70 CONTINUOUS MODE 100 95 EFFICIENCY (%) 90 85 80 75 70 3.3VIN 1.2VOUT 3.3VIN 1.5VOUT 3.3VIN 1.8VOUT 3.3VIN 2.5VOUT 0 2 4 LOAD CURRENT 6 8 4608A G02 Efficiency vs Load Current CONTINUOUS MODE 100 95 90 85 80 75 70 Efficiency vs Load Current CONTINUOUS MODE 5VIN 1.2VOUT 5VIN 1.5VOUT 5VIN 1.8VOUT 5VIN 2.5VOUT 5VIN 3.3VOUT 0 2 4 LOAD CURRENT 6 8 4608A G01 2.7VIN 1.0VOUT 2.7VIN 1.5VOUT 2.7VIN 1.8VOUT 0 1 4 3 2 5 LOAD CURRENT (A) 6 7 4608A G03 Burst Mode Efficiency with 5V Input 100 90 EFFICIENCY (%) 80 VOUT (V) 70 60 50 40 VOUT = 1.5V VOUT = 2.5V VOUT = 3.3V 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 LOAD CURRENT (A) 4608A G04 VIN to VOUT Step-Down Ratio 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 2 IOUT = 8A VOUT = 1.2V VOUT = 1.5V 3 4 VIN (V) 4608A G05 VIN to VOUT Step-Down Ratio 4.0 3.5 3.0 2.5 VOUT (V) 2.0 1.5 1.0 0.5 6 0 2 IOUT = 6A VOUT = 1.2V VOUT = 1.5V 3 4 VIN (V) 4608A G06 VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V 5 VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V 5 6 Supply Current vs VIN 1.6 1.4 SUPPLY CURRENT (mA) 1.2 1 0.8 0.6 0.4 0.2 0 2.5 3 3.5 4 4.5 INPUT VOLTAGE (V) 5 5.5 4608A G07 Load Transient Response ILOAD 1A/DIV Load Transient Response VO = 1.2V PULSE-SKIPPING MODE VIN 2V/DIV VOUT 20mV/DIV AC COUPLED ILOAD 2A/DIV VOUT 20mV/DIV AC COUPLED VO = 1.2V BURST MODE 4608A G08 VIN = 5V 20µs/DIV VOUT = 3.3V, RFB = 2.21k 2A/µs STEP COUT = 100µF X5R C1 = 100pF C3 = 22pF FROM FIGURE 18 , 4608A G09 VIN = 5V 20µs/DIV VOUT = 2.5V, RFB = 3.09k 2.5A/µs STEP COUT = 100µF X5R C1 = 120pF C3 = 47pF FROM FIGURE 18 , 4608afc 5 LTM4608A TYPICAL PERFORMANCE CHARACTERISTICS Load Transient Response Load Transient Response Load Transient Response ILOAD 2A/DIV VOUT 20mV/DIV AC COUPLED ILOAD 2A/DIV VOUT 20mV/DIV AC COUPLED ILOAD 2A/DIV VOUT 20mV/DIV AC COUPLED 4608A G10 VIN = 5V 20µs/DIV VOUT = 1.8V, RFB = 4.87k 2.5A/µs STEP COUT = 100µF X5R C1 = NONE, C3 = NONE FROM FIGURE 18 4608A G11 VIN = 5V 20µs/DIV VOUT = 1.5V, RFB = 6.65k 2.5A/µs STEP COUT = 100µF X5R C1 = NONE, C3 = NONE FROM FIGURE 18 4608A G12 VIN = 5V 20µs/DIV VOUT = 1.2V, RFB = 10k 2.5A/µs STEP COUT = 2 × 100µF C1 = 100pF C3 = NONE FROM FIGURE 18 , Start-Up 602 VOUT 0.5V/DIV VIN 2V/DIV VFB (mV) 600 VFB vs Temperature 0 –0.1 LOAD REGULATION (%) VIN = 5.5V 598 596 VIN = 2.7V 594 VIN = 3.3V –0.2 –0.3 –0.4 –0.5 –0.6 Load Regulation vs Current VIN = 5V 50µs/DIV VOUT = 1.5V COUT = 100µF NO LOAD AND 8A LOAD (DEFAULT 100µs SOFT-START) 4608A G13 592 590 –55 FC MODE VIN = 3.3V VOUT = 1.5V 0 2 4 6 LOAD CURRENT (A) 8 4608A G15 –25 65 35 TEMPERATURE (°C) 5 95 125 4608A G14 2.5V Output Current 3.0 2.5 OUTPUT VOLTAGE (V) 2.0 1.5 1.0 0.5 0 2V/DIV 2V/DIV Short-Circuit Protection (2.5V Short, No Load) VIN Short-Circuit Protection (2.5V Short, 4A Load) 5V/DIV 5V/DIV VIN VOUT IOUT LOAD VOUT 5A/DIV 5A/DIV IOUT VIN = 5V VOUT = 2.5V 0 5 10 15 OUTPUT CURRENT (A) 20 4608A G16 50µs/DIV 4608A G17 VIN = 5V VOUT = 2.5V 50µs/DIV 4608A G18 4608afc 6 LTM4608A PIN FUNCTIONS VIN (C1, C8, C9, D1, D3-D5, D7-D9 and E8): Power Input Pins. Apply input voltage between these pins and GND pins. Recommend placing input decoupling capacitance directly between VIN pins and GND pins. VOUT (C10-C11, D10-D11, E9-E11, F9-F11, G9-G11): Power Output Pins. Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly between these pins and GND pins. See Table 1. GND (A1-A11, B1, B9-B11, F3, F7-F8, G1-G8): Power Ground Pins for Both Input and Output Returns. SVIN (F4): Signal Input Voltage. This pin is internally connected to VIN through a lowpass filter. SGND (E1): Signal Ground Pin. Return ground path for all analog and low power circuitry. Tie a single connection to GND in the application. MODE (B5): Mode Select Input. Tying this pin high enables Burst Mode operation. Tying this pin low enables forced continuous operation. Floating this pin or tying it to VIN/2 enables pulse-skipping operation. CLKIN (B3): External Synchronization Input to Phase Detector. This pin is internally terminated to SGND with a 50k resistor. The phase locked loop will force the internal top power PMOS turn on to be synchronized with the rising edge of the CLKIN signal. Connect this pin to SVIN to enable spread spectrum modulation. During external synchronization, make sure the PLLLPF pin is not tied to VIN or GND. PLLLPF (E3): Phase Locked Loop Lowpass Filter. An internal lowpass filter is tied to this pin. In spread spectrum mode, placing a capacitor here to SGND controls the slew rate from one frequency to the next. Alternatively, floating this pin allows normal running frequency at 1.5MHz, tying this pin to SVIN forces the part to run at 1.33 times its normal frequency (2MHz), tying it to ground forces the frequency to run at 0.67 times its normal frequency (1MHz). PHMODE (B4): Phase Selector Input. This pin determines the phase relationship between the internal oscillator and CLKOUT. Tie it high for 2-phase operation, tie it low for 3-phase operation, and float or tie it to VIN/2 for 4-phase operation. MGN (B8): Margining Pin. Increases or decreases the output voltage by the amount specified by the BSEL pin. To disable margining, tie the MGN pin to a voltage divider with 50k resistors from VIN to ground. See the Applications Information section and Figure 20. BSEL (B7): Margining Bit Select Pin. Tying BSEL low selects ±5%, tying it high selects ±10%. Floating it or tying it to VIN/2 selects ±15%. TRACK (E5): Output Voltage Tracking Pin. Voltage tracking is enabled when the TRACK voltage is below 0.57V. If tracking is not desired, then connect the TRACK pin to SVIN. If TRACK is not tied to SVIN, then the TRACK pin’s voltage needs to be below 0.18V before the chip shuts down even though RUN is already low. Do not float this pin. A resistor divider and capacitor can be applied to the TRACK pin to increase the soft-start time of the regulator. See the Applications Information section. Can tie together for parallel operation and tracking. Load current needs to be present during track down. 4608afc 7 LTM4608A PIN FUNCTIONS FB (E7): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT with a 10k precision resistor. Different output voltages can be programmed with an additional resistor between FB and GND pins. In PolyPhase® operation, tie FB pins together for parallel operation. See the Applications Information section for details. ITH (F6): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. Tie together in parallel operation. ITHM (F5): Negative Input to the Internal ITH Differential Amplifier. Tie this pin to SGND for single phase operation. For PolyPhase operation, tie the master’s ITHM to SGND while connecting all of the ITHM pins together. PGOOD (C7): Output Voltage Power Good Indicator. Open-drain logic output that is pulled to ground when the output voltage is not within ±10% of the regulation point. Disabled during margining. RUN (F1): Run Control Pin. A voltage above 1.5V will turn on the module. SW (C3-C5): Switching Node of the Circuit is Used for Testing Purposes. This can be connected to an electrically open circuit copper pad on the board for improved thermal performance. CLKOUT (F2): Output Clock Signal for PolyPhase Operation. The phase of CLKOUT is determined by the state of the PHMODE pin. 4608afc 8 LTM4608A SIMPLIFIED BLOCK DIAGRAM SVIN TRACK MGN BSEL PGOOD MODE RUN CLKIN CLKOUT PHMODE ITH INTERNAL COMP 10k FB INTERNAL FILTER RFB 6.65k M2 22µF 22pF GND COUT POWER CONTROL M1 0.22µH SW INTERNAL FILTER VIN 10µF 10µF 10µF + VIN 2.7 TO 5.5V CIN VOUT VOUT 1.5V PLLLPF ITHM SGND 4608A BD Figure 1. Simplified LTM4608A Block Diagram Table 1. Decoupling Requirements. TA = 25°C, Block Diagram Configuration SYMBOL CIN COUT PARAMETER External Input Capacitor Requirement (VIN = 2.7V to 5.5V, VOUT = 1.5V) External Output Capacitor Requirement (VIN = 2.7V to 5.5V, VOUT = 1.5V) CONDITIONS IOUT = 8A IOUT = 8A MIN 10 100 TYP MAX UNITS µF µF OPERATION The LTM4608A is a standalone nonisolated switch mode DC/DC power supply. It can deliver up to 8A of DC output current with few external input and output capacitors. This module provides precisely regulated output voltage programmable via one external resistor from 0.6V DC to 5.0V DC over a 2.7V to 5.5V input voltage. The typical application schematic is shown in Figure 18. The LTM4608A has an integrated constant frequency current mode regulator and built-in power MOSFET devices with fast switching speed. The typical switching frequency is 1.5MHz. For switching noise sensitive applications, it can be externally synchronized from 0.75MHz to 2.25MHz. Even spread spectrum switching can be implemented in the design to reduce noise. 4608afc 9 LTM4608A OPERATION With current mode control and internal feedback loop compensation, the LTM4608A module has sufficient stability margins and good transient performance with a wide range of output capacitors, even with all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limit and thermal shutdown in an overcurrent condition. Internal overvoltage and undervoltage comparators pull the open-drain PGOOD output low if the output feedback voltage exits a ±10% window around the regulation point. Pulling the RUN pin below 1.3V forces the controller into its shutdown state, by turning off both M1 and M2 at low load current. The TRACK pin is used for programming the output voltage ramp and voltage tracking during start-up. See Applications Information. The LTM4608A is internally compensated to be stable over all operating conditions. Table 3 provides a guideline for input and output capacitances for several operating conditions. The Linear Technology µModule Power Design Tool is provided for transient and stability analysis. The FB pin is used to program the output voltage with a single external resistor to ground. Multiphase operation can be easily employed with the synchronization and phase mode controls. Up to 12 phases can be cascaded to run simultaneously with respect to each other by programming the PHMODE pin to different levels. The LTM4608A has clock in and clock out for poly phasing multiple devices or frequency synchronization. High efficiency at light loads can be accomplished with selectable Burst Mode operation using the MODE pin. These light load features will accommodate battery operation. Efficiency graphs are provided for light load operation in the Typical Performance Characteristics. Output voltage margining is supported, and can be programed from ±5% to ±15% using the MGN and BSEL pins. The PGOOD pin is disabled during margining APPLICATIONS INFORMATION The typical LTM4608A application circuit is shown in Figure 18. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 3 for specific external capacitor requirements for a particular application. VIN to VOUT Step-Down Ratios There are restrictions in the maximum VIN to VOUT stepdown ratio that can be achieved for a given input voltage. The LTM4608A is 100% duty cycle, but the VIN to VOUT minimum dropout is a function of its load current. Please refer to the curves in the Typical Performance Characteristics section of this data sheet for more information. Output Voltage Programming The PWM controller has an internal 0.596V reference voltage. As shown in the Block Diagram, a 10k 0.5% internal feedback resistor connects VOUT and FB pins together. The output voltage will default to 0.596V with no feedback resistor. Adding a resistor RFB from FB pin to GND programs the output voltage: VOUT = 0.596V • 10k + RFB RFB 1.5V 6.65k 1.8V 4.87k 2.5V 3.09k 3.3V 2.21k Table 2. RFB Resistor vs Output Voltage VOUT RFB 0.596V Open 1.2V 10k Input Capacitors The LTM4608A module should be connected to a low AC impedance DC source. Three 10µF ceramic capacitors are included inside the module. Additional input capacitors are only needed if a large load step is required up to the 4A level. A 47µF to 100µF surface mount aluminum electrolytic bulk capacitor can be used for more input bulk capacitance. This bulk input capacitor is only needed if the input source impedance is compromised by long inductive leads, traces or not enough source capacitance. 4608afc 10 LTM4608A APPLICATIONS INFORMATION If low impedance power planes are used, then this 47µF capacitor is not needed. For a buck converter, the switching duty-cycle can be estimated as: D= VOUT VIN a function of stability and transient response. The Linear Technology LTpowerCAD Design Tool will calculate the output ripple reduction as the number phases implemented increases by N times. Burst Mode Operation The LTM4608A is capable of Burst Mode operation in which the power MOSFETs operate intermittently based on load demand, thus saving quiescent current. For applications where maximizing the efficiency at very light loads is a high priority, Burst Mode operation should be applied. To enable Burst Mode operation, simply tie the MODE pin to VIN. During this operation, the peak current of the inductor is set to approximately 20% of the maximum peak current value in normal operation even though the voltage at the ITH pin indicates a lower value. The voltage at the ITH pin drops when the inductor’s average current is greater than the load requirement. As the ITH voltage drops below 0.2V, the BURST comparator trips, causing the internal sleep line to go high and turn off both power MOSFETs. In sleep mode, the internal circuitry is partially turned off, reducing the quiescent current to about 450µA. The load current is now being supplied from the output capacitor. When the output voltage drops, causing ITH to rise above 0.25V, the internal sleep line goes low, and the LTM4608A resumes normal operation. The next oscillator cycle will turn on the top power MOSFET and the switching cycle repeats. Pulse-Skipping Mode Operation In applications where low output ripple and high efficiency at intermediate currents are desired, pulse-skipping mode should be used. Pulse-skipping operation allows the LTM4608A to skip cycles at low output loads, thus increasing efficiency by reducing switching loss. Floating the MODE pin or tying it to VIN/2 enables pulse-skipping operation. This allows discontinuous conduction mode (DCM) operation down to near the limit defined by the chip’s minimum on-time (about 100ns). Below this output current level, the converter will begin to skip cycles in order to maintain output regulation. Increasing the output load current slightly, above the minimum required for discontinuous conduction mode, allows constant frequency PWM. 4608afc Without considering the inductor current ripple, the RMS current of the input capacitor can be estimated as: ICIN(RMS) = IOUT(MAX) η% • D • (1– D) In the above equation, η% is the estimated efficiency of the power module. The bulk capacitor can be a switcherrated electrolytic aluminum capacitor, polymer capacitor for bulk input capacitance due to high inductance traces or leads. If a low inductance plane is used to power the device, then only one 10µF ceramic is required. The three internal 10µF ceramics are typically rated for 2A of RMS ripple current, so the ripple current at the worse case for 8A maximum current is 4A or less. Output Capacitors The LTM4608A is designed for low output voltage ripple noise. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, a low ESR polymer capacitor or ceramic capacitor. The typical output capacitance range is from 47µF to 220µF Additional . output filtering may be required by the system designer, if further reduction of output ripple or dynamic transient spikes is desired. Table 3 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 3A/µs transient. The table optimizes total equivalent ESR and total bulk capacitance to optimize the transient performance. Stability criteria are considered in the Table 3 matrix, and the Linear Technology LTpowerCAD™ Design Tool is available for stability analysis. Multiphase operation will reduce effective output ripple as a function of the number of phases. Application Note 77 discusses this noise reduction versus output ripple current cancellation, but the output capacitance will be more 11 LTM4608A APPLICATIONS INFORMATION Table 3. Output Voltage Response Versus Component Matrix (Refer to Figure 18) 0A to 3A Load Step TYPICAL MEASURED VALUES VALUE COUT1 VENDORS TDK 22µF 6.3V , Murata 22µF 16V , TDK 100µF 6.3V , Murata 100µF 6.3V , VOUT (V) 1.0 1.0 1.0 1.0 1.0 1.0 1.2 1.2 1.2 1.2 1.2 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.8 1.8 CIN (CERAMIC) 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF CIN (BULK)* 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF 100µF PART NUMBER C3216X7S0J226M GRM31CR61C226KE15L C4532X5R0J107MZ GRM32ER60J107M COUT1 (CERAMIC) 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 2 22µF × 1 100µF × 1 22µF × 1 COUT2 (BULK) 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 150µF × 2 COUT2 VENDORS Sanyo POSCAP CIN (BULK) VENDORS Sanyo VALUE 150µF 10V , VALUE 100µF 10V , PART NUMBER 10TPD150M PART NUMBER 10CE100FH ITH None None None None None None None None None None None None None None None None None None None None C1 68pF None 68pF None 68pF None 100pF None 100pF None 100pF 47pF 100pF None 100pF None 100pF None 47pF None 120pF None 120pF None 100pF 22pF 100pF 22pF 22pF None C3 None 100pF None 100pF None 100pF None 100pF None 100pF None None None 47pF None 47pF None None None 47pF None 47pF None None None None None None None None VIN (V) 5 5 3.3 3.3 2.7 2.7 5 5 3.3 3.3 2.7 2.7 5 5 3.3 3.3 2.7 2.7 5 5 3.3 3.3 2.7 2.7 5 5 3.3 3.3 5 5 DROOP (mV) 13 17 13 17 13 17 16 20 16 20 16 16 18 20 16 20 18 20 22 21 21 21 22 21 28 33 30 21 38 39 PEAK-TO- PEAK DEVIATION (mV) 26 34 26 34 26 34 32 41 32 41 32 32 36 41 32 41 36 41 42 42 43 41 44 42 42 60 60 41 74 75 RECOVERY TIME (µs) 7 8 7 10 7 8 8 10 8 10 10 8 8 12 10 12 10 12 8 12 12 12 12 14 10 10 10 10 10 12 LOAD STEP (A/µs) 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 RFB (kΩ) 14.7 14.7 14.7 14.7 14.7 14.7 10 10 10 10 10 10 6.65 6.65 6.65 6.65 6.65 6.65 4.87 4.87 4.87 4.87 4.87 4.87 3.09 3.09 3.09 3.09 2.21 2.21 1.8 10µF 100µF 100µF × 2 None 1.8 10µF 100µF 22µF × 1 150µF × 2 None 1.8 10µF 100µF 100µF × 2 None 1.8 10µF 100µF 22µF × 1 150µF × 2 None 2.5 10µF 100µF 100µF × 1 None 2.5 10µF 100µF 22µF × 1 150µF × 1 None 2.5 10µF 100µF 100µF × 1 None 2.5 10µF 100µF 22µF × 1 150µF × 1 None 3.3 10µF 100µF 100µF × 1 100pF 3.3 10µF 100µF 22µF × 1 150µF × 1 None *Bulk capacitance is optional if VIN has very low input impedance. Forced Continuous Operation In applications where fixed frequency operation is more critical than low current efficiency, and where the lowest output ripple is desired, forced continuous operation should be used. Forced continuous operation can be enabled by tying the MODE pin to GND. In this mode, inductor current is allowed to reverse during low output loads, the ITH voltage is in control of the current comparator threshold throughout, and the top MOSFET always turns on with each oscillator pulse. During start-up, forced continuous mode is disabled and inductor current is prevented from reversing until the LTM4608A’s output voltage is in regulation. Multiphase Operation For output loads that demand more than 8A of current, multiple LTM4608As can be cascaded to run out of phase to 4608afc 12 LTM4608A APPLICATIONS INFORMATION provide more output current without increasing input and output voltage ripple. The CLKIN pin allows the LTM4608A to synchronize to an external clock (between 0.75MHz and 2.25MHz) and the internal phase locked loop allows the LTM4608A to lock onto CLKIN’s phase as well. The CLKOUT signal can be connected to the CLKIN pin of the following LTM4608A stage to line up both the frequency and the phase of the entire system. Tying the PHMODE pin to SVIN, SGND or SVIN/2 (floating) generates a phase difference (between CLKIN and CLKOUT) of 180°, 120° or 90° respectively, which corresponds to a 2-phase, 3-phase or 4-phase operation. A total of 6 phases can be cascaded to run simultaneously with respect to each other by programming the PHMODE pin of each LTM4608A to different levels. For a 6-phase example in Figure 2, the 2nd stage that is 120° out of phase from the 1st stage can generate a 240° (PHMODE = 0) CLKOUT signal for the 3rd stage, which then can generate a CLKOUT signal that’s 420°, or 60° (PHMODE = SVIN) for the 4th stage. With the 60° CLKIN input, the next two stages can shift 120° (PHMODE = 0) for each to generate a 300° signal for the 6th stage. Finally, the signal with a 60° phase shift on the 6th stage (PHMODE is floating) goes back to the 1st stage. Figure 3 shows the configuration for 12-phase operation. A multiphase power supply significantly reduces the amount of ripple current in both the input and output capacitors. The RMS input ripple current is reduced by, and the effective ripple frequency is multiplied by, the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by the number of phases used. 0 CLKIN CLKOUT PHMODE PHASE 1 +120 120 CLKIN CLKOUT PHMODE PHASE 3 +120 240 CLKIN CLKOUT PHMODE PHASE 5 +180 (420) 60 CLKIN CLKOUT PHMODE PHASE 2 +120 180 CLKIN CLKOUT PHMODE PHASE 4 +120 300 CLKIN CLKOUT PHMODE PHASE 6 SVIN 4608A F02 Figure 2. 6-Phase Operation 0 CLKIN CLKOUT PHMODE V+ OUT1 LTC6908-2 OUT2 90 CLKIN CLKOUT PHMODE PHASE 4 +120 PHASE 1 +120 120 CLKIN CLKOUT PHMODE PHASE 5 +120 240 CLKIN CLKOUT PHMODE PHASE 9 +180 (420) 60 CLKIN CLKOUT PHMODE PHASE 3 (510) 150 +180 CLKIN CLKOUT PHMODE PHASE 6 +120 +120 180 CLKIN CLKOUT PHMODE PHASE 7 +120 300 CLKIN CLKOUT PHMODE PHASE 11 (390) 30 +120 CLKIN CLKOUT PHMODE PHASE 2 SVIN 4608 F02 210 CLKIN CLKOUT PHMODE PHASE 8 +120 330 CLKIN CLKOUT PHMODE PHASE 12 270 CLKIN CLKOUT PHMODE PHASE 10 SVIN 4608A F03 Figure 3. 12-Phase Operation 4608afc 13 LTM4608A APPLICATIONS INFORMATION The LTM4608A device is an inherently current mode controlled device. Parallel modules will have very good current sharing. This will balance the thermals on the design. Tie the ITH pins of each LTM4608A together to share the current evenly. To reduce ground potential noise, tie the ITHM pins of all LTM4608As together and then connect to the SGND at only one point. Figure 19 shows a schematic of the parallel design. The FB pins of the parallel module are tied together. With parallel operation, input and output capacitors may be reduced in part according to the operating duty cycle. Input RMS Ripple Current Cancellation Application Note 77 provides a detailed explanation of multiphase operation. The input RMS ripple current cancellation mathematical derivations are presented, and a graph is displayed representing the RMS ripple current reduction as a function of the number of interleaved phases. Figure 4 shows this graph. 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE Spread Spectrum Operation Switching regulators can be particularly troublesome where electromagnetic interference (EMI) is concerned. Switching regulators operate on a cycle-by-cycle basis to transfer power to an output. In most cases, the frequency of operation is fixed based on the output load. This method of conversion creates large components of noise at the frequency of operation (fundamental) and multiples of the operating frequency (harmonics). To reduce this noise, the LTM4608A can run in spread spectrum operation by tying the CLKIN pin to SVIN. In spread spectrum operation, the LTM4608A’s internal oscillator is designed to produce a clock pulse whose period is random on a cycle-by-cycle basis but fixed between 70% and 130% of the nominal frequency. This has the benefit of spreading the switching noise over a range of frequencies, thus significantly reducing the peak noise. Spread spectrum operation is disabled if RMS INPUT RIPPLE CURRENT DC LOAD CURRENT 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 DUTY FACTOR (VO/VIN) 4608A F04 Figure 4. Normalized Input RMS Ripple Current vs Duty Factor for One to Six Phases 4608afc 14 LTM4608A APPLICATIONS INFORMATION CLKIN is tied to ground or if it’s driven by an external frequency synchronization signal. A capacitor value of 0.01µF must be placed from the PLLLPF pin to ground to control the slew rate of the spread spectrum frequency change. Add a control ramp on the TRACK pin with RSR and CSR referenced to VIN. Figure 21 shows an example for spread spectrum operation. 1 RSR ≥   0.592   − ln 1− • 500 • CSR   VIN    Output Voltage Tracking Output voltage tracking can be programmed externally using the TRACK pin. The output can be tracked up and down with another regulator. The master regulator’s output is divided down with an external resistor divider that is the same as the slave regulator’s feedback divider to implement coincident tracking. The LTM4608A uses an accurate 10k resistor internally for the top feedback resistor. Figure 5 shows an example of coincident tracking:  10k  Slave = 1+  • VTRACK  RFB4  VTRACK is the track ramp applied to the slave’s track pin. VTRACK has a control range of 0V to 0.596V, or the internal reference voltage. When the master’s output is divided down with the same resistor values used to set the slave’s output, this resistor divider is connected to the slave’s track pin. The slave will then coincident track with the master until it reaches its final value. The master will continue to its final value from the slave’s regulation point. Voltage tracking is disabled when VTRACK is more than 0.596V. VIN 5V TIE TO VIN FOR DISABLE AND DEFAULT 100µs SOFT-START RSR CSR VIN SVIN SW RUN TRACK RUN TRACK MODE CLKIN VOUT FB ITH ITHM PGOOD BSEL C2 100pF RFB1 2.21k 100µF C3 22pF VIN 50k MASTER 3.3V 7A LTM4608A PLLLPF PHMODE MGN APPLY A CONTROL CLKOUT GND SGND RAMP WITH RSR AND CSR TIED TO VIN WHERE t = –(ln (1 – 0.596/VIN) • RSR • CSR) OR APPLY AN EXTERNAL TRACKING RAMP CLKIN 50k VIN SVIN MASTER 3.3V RFB3 10k RFB4 6.65k SW RUN TRACK RUN TRACK MODE PHMODE VOUT FB ITH ITHM PGOOD BSEL MGN RFB2 6.65k C1 100µF + C4 100µF SLAVE 1.5V 8A LTM4608A PLLLPF CLKOUT GND SGND 4608A F05 Figure 5. Dual Outputs (3.3V and 1.5V) with Tracking 4608afc 15 LTM4608A APPLICATIONS INFORMATION The track pin of the master can be controlled by an external ramp or by RSR and CSR in Figure 5 referenced to VIN. The RC ramp time can be programmed using equation: MASTER OUTPUT OUTPUT VOLTAGE (V)   0.596V   t = – ln 1–  • RSR • CSR    VIN    Ratiometric tracking can be achieved by a few simple calculations and the slew rate value applied to the master’s track pin. As mentioned above, the TRACK pin has a control range from 0V to 0.596V. The master’s TRACK pin slew rate is directly equal to the master’s output slew rate in Volts/Time: MR • 10k = RFB3 SR SLAVE OUTPUT TIME 4608A F06 Figure 6. Output Voltage Coincident Tracking where MR is the master’s output slew rate and SR is the slave’s output slew rate in Volts/Time. When coincident tracking is desired, then MR and SR are equal, thus RFB3 is equal the 10k. RFB4 is derived from equation: RFB4 = 0.596V VFB VFB VTRACK + – 10k RFB2 RFB3 For example: MR = 3.3V/ms and SR = 1.5V/ms. Then RFB3 = 22.1k. Solve for RFB4 to equal to 4.87k. For applications that do not require tracking or sequencing, simply tie the TRACK pin to SVIN to let RUN control the turn on/off. Connecting TRACK to SVIN also enables the ~100µs of internal soft-start during start-up. Load current needs to be present during track down. Power Good The PGOOD pin is an open-drain pin that can be used to monitor valid output voltage regulation. This pin monitors a ±10% window around the regulation point. As shown in Figure 20, the sequencing function can be realized in a dual output application by controlling the RUN pins and the PGOOD signals from each other. The 1.5V output begins its soft starting after the PGOOD signal of 3.3V output becomes high, and 3.3V output starts its shut down after the PGOOD signal of 1.5V output becomes low. This can be applied to systems that require voltage sequencing between the core and sub-power supplies. where VFB is the feedback voltage reference of the regulator and VTRACK is 0.596V. Since RFB3 is equal to the 10k top feedback resistor of the slave regulator in equal slew rate or coincident tracking, then RFB4 is equal to RFB2 with VFB = VTRACK. Therefore RFB3 = 10k and RFB4 = 6.65k in Figure 5. In ratiometric tracking, a different slew rate maybe desired for the slave regulator. RFB3 can be solved for when SR is slower than MR. Make sure that the slave supply slew rate is chosen to be fast enough so that the slave output voltage will reach it final value before the master output. 4608afc 16 LTM4608A APPLICATIONS INFORMATION Slope Compensation The module has already been internally compensated for all output voltages. Table 3 is provided for most application requirements. A spice model will be provided for other control loop optimization. For single module operation, connect ITHM pin to SGND. For parallel operation, tie ITHM pins together and then connect to SGND at one point. Tie ITH pins together to share currents evenly for all phases. Output Margining For a convenient system stress test on the LTM4608A’s output, the user can program the LTM4608A’s output to ±5%, ±10% or ±15% of its normal operational voltage. The margin pin with a voltage divider is driven with a small three-state gate as shown in Figure 18, for the three margin states (high, low, no margin). When the MGN pin is < 0.3V, it forces negative margining in which the output voltage is below the regulation point. When MGN is >VIN – 0.3V, the output voltage is forced above the regulation point. The amount of output voltage margining is determined by the BSEL pin. When BSEL is low, it is 5%. When BSEL is 4.0 3.5 3.0 POWER LOSS (W) POWER LOSS (W) 2.5 2.0 1.5 1.0 0.5 0 0 2 4 LOAD CURRENT (A) 4608A F07 high, it is 10%. When BSEL is floating, it is 15%. When margining is active, the internal output overvoltage and undervoltage comparators are disabled and PGOOD remains high. Margining is disabled by tying the MGN pin to a voltage divider as shown in Figure 20. Thermal Considerations and Output Current Derating The power loss curves in Figures 7 and 8 can be used in coordination with the load current derating curves in Figures 9 to 16 for calculating an approximate θJA for the module with various heat sinking methods. Thermal models are derived from several temperature measurements at the bench, and thermal modeling analysis. Thermal Application Note 103 provides a detailed explanation of the analysis for the thermal models and the derating curves. Tables 4 and 5 provide a summary of the equivalent θJA for the noted conditions. These equivalent θJA parameters are correlated to the measured values and improve with air flow. The junction temperature is maintained at 125°C or below for the derating curves. 4.0 3.5 3.0 2.5 2.0 1.5 1.0 3.3VIN 1.5VOUT 3.3VIN 2.5VOUT 6 8 0.5 0 0 2 4 LOAD CURRENT (A) 4608A F08 5VIN 1.5VOUT 5VIN 3.3VOUT 6 8 Figure 7. 3.3VIN, 2.5V and 1.5VOUT Power Loss Figure 8. 5VIN, 3.3V and 1.5VOUT Power Loss 4608afc 17 LTM4608A APPLICATIONS INFORMATION 9 8 7 LOAD CURRENT (A) LOAD CURRENT (A) 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F09 9 8 7 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F10 Figure 9. No Heat Sink with 3.3VIN to 1.5VOUT 9 8 7 LOAD CURRENT (A) Figure 10. BGA Heat Sink with 3.3VIN to 1.5VOUT 9 8 7 LOAD CURRENT (A) 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F12 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F11 Figure 11. No Heat Sink with 5VIN to 1.5VOUT 9 8 7 LOAD CURRENT (A) Figure 12. BGA Heat Sink with 5VIN to 1.5VOUT 9 8 7 LOAD CURRENT (A) 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F14 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F13 Figure 13. No Heat Sink with 3.3VIN to 2.5VOUT Figure 14. BGA Heat Sink with 3.3VIN to 2.5VOUT 4608afc 18 LTM4608A APPLICATIONS INFORMATION 9 8 7 LOAD CURRENT (A) 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F15 9 8 7 LOAD CURRENT (A) 6 5 4 3 2 1 0 40 50 400LFM 200LFM 0LFM 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) 4608A F16 Figure 15. No Heat Sink with 5VIN to 3.3VOUT Figure 16. BGA Heat Sink with 5VIN to 3.3VOUT Table 4. 1.5V Output DERATING CURVE Figures 9, 11 Figures 9, 11 Figures 9, 11 Figures 10, 12 Figures 10, 12 Figures 10, 12 VIN (V) 3.3, 5 3.3, 5 3.3, 5 3.3, 5 3.3, 5 3.3, 5 POWER LOSS CURVE Figures 7, 8 Figures 7, 8 Figures 7, 8 Figures 7, 8 Figures 7, 8 Figures 7, 8 AIR FLOW (LFM) 0 200 400 0 200 400 HEAT SINK None None None BGA Heat Sink BGA Heat Sink BGA Heat Sink θJA (°C/W) 25 21 20 23.5 22 22 Table 5. 3.3V Output DERATING CURVE Figure 15 Figure 15 Figure 15 Figure 16 Figure 16 Figure 16 VIN (V) 5 5 5 5 5 5 POWER LOSS CURVE Figure 8 Figure 8 Figure 8 Figure 8 Figure 8 Figure 8 AIR FLOW (LFM) 0 200 400 0 200 400 HEAT SINK None None None BGA Heat Sink BGA Heat Sink BGA Heat Sink θJA (°C/W) 25 21 20 23.5 22 22 4608afc 19 LTM4608A APPLICATIONS INFORMATION Safety Considerations The LTM4608A modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. Layout Checklist/Example The high integration of LTM4608A makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. • Use large PCB copper areas for high current path, including VIN, GND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. • Place high frequency ceramic input and output capacitors next to the VIN, GND and VOUT pins to minimize high frequency noise. • Place a dedicated power ground layer underneath the unit. • To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. • Do not put vias directly on the pads, unless they are capped. • Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to GND underneath the unit. Figure 17 gives a good example of the recommended layout. GND VOUT COUT COUT COUT GND CIN VIN CIN GND 4608A F17 Figure 17. Recommended PCB Layout 4608afc 20 LTM4608A TYPICAL APPLICATIONS CLKIN VIN 3V TO 5.5V CLKIN VOUT 2.5V 8A 8A AT 5V INPUT 6A AT 3.3V INPUT CIN 10µF VIN SVIN SW RUN TRACK MODE PHMODE MODE PHMODE LTM4608A FB ITH ITHM PGOOD BSEL MGN 50k BSEL RFB 3.09k VOUT C1 220pF C3 47pF COUT 100µF VIN 100k PGOOD VIN (HIGH = 10%) (FLOAT = 15%) (LOW = 5%) 1 50k YOUT 4 5 2 U1 U1: PERICOM PI74ST1G126CEX 3 OR TOSHIBA TC7SZ126AFE MARGIN VALUE OE AIN PLLLPF CLKOUT GND SGND 4608A F18 OE AIN YOUT MGN H H L H L X H L Z H + OF BSEL SELECTION L – OF BSEL SELECTION NO MARGIN VIN/2 Figure 18. Typical 3V to 5.5VIN, 2.5V at 8A Design VIN 3V TO 5.5V VIN 10µF SVIN SW RUN TRACK RUN TRACK MODE PHMODE CLKIN VOUT FB ITH ITHM PGOOD BSEL MGN C4 100pF 3.32k LTM4608A 100µF 6.3V X5R VOUT 1.5V 16A PLLLPF CLKOUT GND SGND C3 100µF 6.3V X5R C2 10µF VIN SVIN SW RUN TRACK MODE PHMODE CLKIN VOUT FB ITH ITHM PGOOD BSEL MGN 50k 4608A F19 LTM4608A C1 100µF 6.3V X5R VIN 50k PLLLPF CLKOUT GND SGND Figure 19. Two LTM4608As in Parallel, 1.5V at 16A Design. See Also Dual 8A per Channel LTM4616 4608afc 21 LTM4608A TYPICAL APPLICATIONS CLKIN VIN 5V D1 MMSD4148 SHDN CLKIN VOUT2 3.3V 7A VIN SVIN SW RUN TRACK MODE PHMODE R1 100k LTM4608A FB ITH ITHM PGOOD BSEL MGN R2 100k 100k VIN 50k 50k SHDN 3.3V 1.5V C3 22pF VOUT C2 100pF RFB1 2.21k 100µF 6.3V X5R PLLLPF CLKOUT GND SGND VIN D2 MMSD4148 SHDN SVIN SW RUN TRACK MODE PHMODE CLKIN VOUT FB ITH ITHM 100k PGOOD BSEL MGN RFB2 6.65k LTM4608A C1 100µF 6.3V X5R + C4 100µF SANYO POSCAP 10m VOUT1 1.5V 8A PLLLPF CLKOUT GND SGND 4608A F20 Figure 20. Dual LTM4608A Output Sequencing Application. See Also Dual 8A per Channel LTM4616 SVIN VIN 2.7V TO 5.5V CLKIN VOUT 1.2V/8A 5A AT 2.7V INPUT VIN 10µF RSR 180k SVIN SW RUN TRACK CSR 0.22µF MODE PHMODE MODE PHMODE VOUT 100pF FB ITH ITHM PGOOD BSEL MGN 4608A F21 LTM4608A 10k C2 100µF 6.3V X5R VIN 50k 50k C1 100µF 6.3V X5R PLLLPF 0.01µF PGOOD BSEL CLKOUT GND SGND Figure 21. 2.7V to 5.5VIN, 1.2VOUT Design in Spread Spectrum Operation 4608afc 22 CLKIN CLKIN VOUT C2 100pF SVIN 3.3V RUN PLLLPF ITHM PGOOD BSEL MGN TRACK MODE PHMODE 50k CLKOUT GND SGND ITH R1 4.87k R8 10k R9 4.87k SW LTM4608A FB C4 22pF R10 2.21k VIN 50k C8 100pF FB ITH ITHM PGOOD BSEL MGN C3 100µF 6.3V X5R VIN VOUT CLKIN VIN 5V VIN SVIN LTM4608A SW VOUT1 3.3V 100µF 7A 6.3V X5R VOUT3 1.8V 8A RUN PLLLPF TYPICAL APPLICATIONS TRACK OR RAMP CONTROL TRACK MODE PHMODE CLKOUT GND SGND VIN C7 220pF SVIN 3.3V RUN TRACK MODE PHMODE R6 10k R7 6.65k SW PLLLPF LTM4608A C8 47pF R2 3.09k C1 100µF 6.3V X5R FB ITH ITHM PGOOD BSEL MGN CLKIN VOUT VIN SVIN LTM4608A VOUT2 2.5V 8A CLKIN VOUT FB ITH ITHM PGOOD BSEL MGN R8 6.65k + C5 100µF 6.3V X5R VOUT4 1.5V 8A 3.3V SW RUN R4 10k PLLLPF C9 100µF 6.3V SANYO POSCAP 10m TRACK R5 3.09k MODE PHMODE CLKOUT GND SGND CLKOUT GND SGND 4608A F22 Figure 22. 4-Phase, Four Outputs (3.3V, 2.5V, 1.8V and 1.5V) with Tracking LTM4608A 23 4608afc LTM4608A PACKAGE DESCRIPTION LGA Package 68-Lead (15mm × 9mm × 2.82mm) (Reference LTC DWG # 05-08-1821 Rev Ø) DETAIL A 2.72 – 2.92 aaa Z G F E D C B A 1 PAD 1 PAD “A1” CORNER 4 2 3 4 5 15.00 BSC MOLD CAP 12.70 BSC 6 7 SUBSTRATE 0.290 – 0.350 2.200 – 2.600 // bbb Z DETAIL B Z 8 9 10 11 9.00 BSC aaa Z X Y 0.630 ±0.025 SQ. 68x eee S X Y DETAIL B 7.620 BSC 1.27 BSC PADS SEE NOTES 3 PACKAGE TOP VIEW 3.810 2.540 1.270 0.000 1.270 2.540 3.810 PACKAGE BOTTOM VIEW DETAIL A 6.350 5.080 3.810 2.540 1.270 0.000 1.270 2.540 3.810 5.080 6.350 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 2. ALL DIMENSIONS ARE IN MILLIMETERS 3 4 LAND DESIGNATION PER JESD MO-222 DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE COMPONENT PIN “A1” 5. PRIMARY DATUM -Z- IS SEATING PLANE 6. THE TOTAL NUMBER OF PADS: 68 SYMBOL TOLERANCE aaa 0.15 bbb 0.10 eee 0.05 LTMXXXXXX µModule TRAY PIN 1 BEVEL PACKAGE IN TRAY LOADING ORIENTATION LGA 68 1207 REV Ø SUGGESTED PCB LAYOUT TOP VIEW PACKAGE PHOTO 4608afc 24 LTM4608A REVISION HISTORY REV B DATE 12/10 DESCRIPTION Voltage changed in the Typical Application drawing. Changes made to the Absolute Maximum Ratings section. Updated the Pin Configuration package dimensions. Changes made to the VOUT conditions in the Electrical Characteristics section. Updated Note 2 in the Electrical Characteristics section. Replaced graphs G05 and G06 in the Typical Performance Characteristics section. Updated MGN (B8) in the Pin Functions section. Text changes made to the Applications Information section. Changes made to Figures 5, 18, 20, 21, 23. Updated the Related Parts table. C 3/11 Updated Pin Configuration drawing Removed Pin Configuration drawing from Pin Functions Added value of 0.22µH to Inductor in Figure 1 Updated Figure 3 Updated Figure 17 Added Package Photo (Revision history begins at Rev B) PAGE NUMBER 1 2 2 2 4 5 7 10, 11, 14, 19 15, 21, 22, 23 26 2 8 9 13 20 24 4608afc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 25 LTM4608A PACKAGE DESCRIPTION Pin Assignment Table (Arranged by Pin Number) PIN NAME A1 A2 A3 A4 A5 A6 A7 A8 A9 GND GND GND GND GND GND GND GND GND PIN NAME B1 B2 B3 B4 B5 B6 B7 B8 B9 GND – CLKIN MODE – BSEL MGN GND PIN NAME C1 C2 C3 C5 C6 C7 C8 C9 VIN – SW SW SW – PGOOD VIN VIN PIN NAME D1 D2 D3 D4 D5 D6 D7 D8 D9 VIN – VIN VIN VIN – VIN VIN VIN PIN NAME E1 E2 E3 E4 E5 E6 E7 E8 E9 SGND – PLLLPF – TRACK – FB VIN VOUT PIN NAME F1 F2 F3 F4 F5 F6 F7 F8 F9 RUN GND SVIN ITHM ITH GND GND VOUT PIN NAME G1 G3 G4 G5 G6 G7 G8 G9 GND GND GND GND GND GND GND GND VOUT CLKOUT G2 PHMODE C4 A10 GND A11 GND B10 GND B11 GND C10 VOUT C11 VOUT D10 VOUT D11 VOUT E10 VOUT E11 VOUT F10 VOUT F11 VOUT G10 VOUT G11 VOUT RELATED PARTS PART NUMBER LTC2900 LTC2923 LTM4600HV LTM4601/ LTM4601A LTM4602 LTM4618 LTM4604A LTM4605 LTM4607 LTM8020 LTM8021 LTM8022 LTM8023 DESCRIPTION Quad Supply Monitor with Adjustable Reset Timer Power Supply Tracking Controller 10A DC/DC µModule Regulator 12A DC/DC µModule Regulator with PLL, Output Tracking/ Margining and Remote Sensing 6A DC/DC µModule Regulator 6A DC/DC µModule Regulator with PLL and Output Tracking/Margining and Remote Sensing Low VIN 4A DC/DC µModule Regulator 5A to 12A Buck-Boost µModule Regulator 5A to 12A Buck-Boost µModule Regulator COMMENTS Monitors Four Supplies; Adjustable Reset Timer Tracks Both Up and Down; Power Supply Sequencing 4.5V ≤ VIN ≤ 28V; 0.6V ≤ VOUT ≤ 5V, LGA Package Guaranteed Operation from –55°C to 125°C Ambient, LGA Package Synchronizable, PolyPhase Operation, LTM4601-1/LTM4601A-1 Version Has No Remote Sensing, LGA Package, MP Version Available Pin Compatible with the LTM4600, LGA Package Synchronizable, PolyPhase Operation 2.375V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.3mm LGA Package 4.5V ≤ VIN ≤ 20V; 0.8V ≤ VOUT ≤ 16V, 15mm × 15mm × 2.8mm LGA Package 4.5V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 25V, 15mm × 15mm × 2.8mm LGA Package LTM4600HVMP Military Plastic 10A DC/DC µModule Regulator High VIN 0.2A DC/DC Step-Down µModule Regulator 4V ≤ VIN ≤ 36V; 1.25V ≤ VOUT ≤ 5V, 6.25mm × 6.25mm × 2.3mm LGA Package High VIN 0.5A DC/DC Step-Down µModule Regulator 3V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 5V, 6.25mm × 11.25mm × 2.8mm LGA Package High VIN 1A DC/DC Step-Down µModule Regulator High VIN 2A DC/DC Step-Down µModule Regulator 3.6V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 10V, 11.25mm × 9mm × 2.8mm LGA Package 3.6V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 10V, 11.25mm × 9mm × 2.8mm LGA Package 4608afc 26 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 l FAX: (408) 434-0507 l LT 0311 REV C • PRINTED IN USA www.linear.com  LINEAR TECHNOLOGY CORPORATION 2008