LTL2R3SEKS2-132A

L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Features * High luminous intensity output. * Low power consumption. * High efficiency. * Versatile mounting on P.C. board or panel. * I.C. Compatible/low current requirements. * Popular T-13/4 diameter. Package Dimensions Part No. LTL2R3SEKS2-132A Lens Water Clear Source Color AlInGaP Super Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Page : 1 of 6 L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Absolute Maximum Ratings at TA=25℃ Parameter Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Continuous Forward Current Derating Linear From 50℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] 100 50 0.6 5 -40℃ to + 100℃ -55℃ to + 100℃ 260℃ for 5 Seconds mA mA mA/℃ V Maximum Rating 130 Unit mW Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Page : 2 of 6 L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Electrical / Optical Characteristics at TA=25℃ Parameter Symbol Min. Typ. Max. Unit Test Condition IF = 20mA Note 1,5 Note 2 (Fig.5) Measurement @Peak (Fig.1) Note 4 Luminous Intensity IV 2θ1/2 λP λd Δλ 1900 3700 mcd Viewing Angle 30 deg Peak Emission Wavelength 639 nm Dominant Wavelength 630 nm Spectral Line Half-Width 17 nm Forward Voltage VF 2.2 2.6 V μA IF = 20mA Reverse Current IR 100 V R = 5V Capacitance C 40 pF VF = 0 , f = 1MHz NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 5. The Iv guarantee should be added ±15﹪tolerance. Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Page : 3 of 6 L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Page : 4 of 6 L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Features * Compatible with radial lead automatic insertion equipment. * Most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * Folding packaging simplifies handling and testing. Package Dimensions Item Tape Feed Hole Diameter Component Lead Pitch Front to Rear Deflection Feed Hole to Bottom of Component Feed Hole to Overall Component Height Lead Length After Component Height Feed Hole Pitch Lead Location Center of Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Symbol D F △H H1 H2 L P P1 P2 T W0 W1 W2 W3 Specification Minimum Maximum mm inch mm inch 3.8 0.149 4.2 0.165 2.3 0.091 3.0 0.118 --2.0 0.078 20.0 0.787 21.0 0.827 28.4 1.118 30.0 1.181 W0 11.0 0.433 12.4 0.488 13.0 0.511 4.4 0.173 5.8 0.228 5.05 0.198 7.65 0.301 --0.90 0.035 8.5 0.334 9.75 0.384 14.5 0.571 15.5 0.610 0 0 3.0 0.118 17.5 0.689 19.0 0.748 Page : 5 of 6 L ITE-ON TECHNOLOGY CORPORATION Property of LITE-ON Only Packing Spec 2000 pcs per inner carton 10 Inner cartons per outer carton total 20000 pcs per outer carton Part No. : LTL2R3SEKS2-132A BNS-OD-C131/A4 Page : 6 of 6