LTL3H3TGUADS1

LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only LED LAMP LTL3H3TGUADS1-132A DATA SHEET FOR CUSTOMER: RGB SIGN Part No. Lens LTL3H3TGUADS1-132A PREPARED BY ENG： Nedphaka BNS-OD-C131/A4 Source Color Green Diffused APPROVED OF PD： Brian Su InGaN Green PREPARED DATE： Feb./21, 2013 REV： A LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Features * High Luminous intensity output. * Low power consumption. * High efficiency. * Wide Viewing Angle Major Axis 100° / Minor Axis 45° * Versatile mounting on P.C. board or panel. * I.C. Compatible/low current requirements. Package Dimensions Part No. Lens Source Color LTL3H3TGUADS1 Green Diffused InGaN Green Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 1 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Absolute Maximum Ratings at TA=25℃ Parameter Power Dissipation Peak Forward Current (Duty Cycle≦1/10, Pulse Width≦10ms) DC Forward Current Derating Linear From 40℃ Reverse Voltage Maximum Rating Unit 110 mW 90 mA 30 mA 0.56 mA/℃ 5 V Operating Temperature Range -30°C to + 85°C Storage Temperature Range -40°C to + 100°C Lead Soldering Temperature [2.0mm (.079") From Body] Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 260°C for 5 Seconds Max. Page : 2 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Electrical / Optical Characteristics at TA=25℃ Parameter Symbol Min. Typ. Max. Unit IV 2900 3800 5000 mcd Luminous Intensity 2θ1/2 100 / 45 deg Peak Emission Wavelength λP 520 nm Dominant Wavelength λd Viewing Angle Spectral Line Half-Width 525 Δλ Forward Voltage VF Reverse Current IR 528 532 30 2.6 3.2 nm Test Condition IF = 20mA Note 1,5 Note 2 (Fig.6) Measurement @Peak (Fig.1) Note 4 nm 3.7 V 50 μA IF = 20mA VR = 5V NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 5. Iv guarantee must be included with ±15% testing tolerance. 6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation. Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 3 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 4 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Features * Compatible with radial lead automatic insertion equipment. * Most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * Folding packaging simplifies handling and testing. Reel packaging is available by removing suffix “A” on option. Package Dimensions Item Tape Feed Hole Diameter Component Lead Pitch Front to Rear Deflection Feed Hole to Bottom of Component Feed Hole to Overall Component Height Lead Length After Component Height Feed Hole Pitch Lead Location Center of Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Position Tape Width Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Symbol D F △H H1 H2 L P P1 P2 T W0 W2 W3 Specification Minimum Maximum mm inch mm inch 3.8 0.149 4.2 0.165 2.3 0.091 3.0 0.118 --2.0 0.078 20.0 0.787 21.0 0.827 25.9 1.020 27.5 1.083 W0 11.0 0.433 12.4 0.488 13.0 0.511 4.4 0.173 5.8 0.228 5.05 0.198 7.65 0.301 --0.90 0.035 8.5 0.334 9.75 0.384 0 0 3.0 0.118 17.5 0.689 19.0 0.748 Page : 5 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Packing Spec Total 2,500pcs per inner carton 10 Inner cartons per outer carton total 25,000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 6 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Bin Table Specification Luminous Intensity Iv(mcd) IF@20mA Bin Code Min. Max. G1 2900 3800 G2 3800 5000 Note: Tolerance of each bin limit is ±15% Dominant Wavelength Unit : nm @20mA Bin Code Bin Code Bin Code GH1 525.0 528.5 GH2 528.5 532.0 Note: Tolerance of each bin limit is ±1nm Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 7 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only CAUTIONS 1. Application This LED lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 5. Soldering When soldering, leave a minimum of 3mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions : Soldering iron Temperature Soldering time Position 350°C Max. 3 seconds Max. (one time only) No closer than 3mm from the base of the epoxy bulb Wave soldering Pre-heat Pre-heat time Solder wave Soldering time Dipping Position 100°C Max. 60 seconds Max. 260°C Max. 5 seconds Max. No lower than 3mm from the base of the epoxy bulb Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 8 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only 6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A Circuit model B LED LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:  Use a conductive wrist band or anti- electrostatic glove when handling these LEDs  All devices, equipment, and machinery must be properly grounded  Work tables, storage racks, etc. should be properly grounded  Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 9 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only Suggested checking list : Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL3H3TGUADS1-132A BNS-OD-C131/A4 Page : 10 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite -On Only 8. Reliability Test Classification Test Item Sample Size Ta = 25°C 45 PCS IF = 30mA *Test Time= 1000hrs (CL=90%; LTPD=5%) High Temperature/ Ta = 85°C 45 PCS High Humidity storage (THB) RH = 85% (CL=90%; LTPD=5%) Operation Life Endurance Test Test Condition *Test Time= 1000hrs Steady state Ta = 85°C, RH= 85 % 76 PCS Operation Life of IF = 10mA High Humidity Heat *Test Time= 500hrs (CL=90%; LTPD=3%) Low Temperature Operation Life of Ta = -30°C 45 PCS IF = 30mA (CL=90%; LTPD=5%) *Test Time= 1000hrs JESD22-A101C (2009) MIL-STD-883G:1008 (2006) Ta= -55 ± 5°C Storage *Test Time= 1000hrs (CL=90%; LTPD=5%) 100°C ～ 25°C ～ -40°C ～ 25°C 76 PCS Cycling MIL-STD-202G:103B (2002) JEITA ED-4701:100 103 (2001) (CL=90%; LTPD=5%) Low Temperature 30mins MIL-STD-883G:1005 (2006) MIL-STD-750D:1031 (1995) Ta= 105 ± 5°C Temperature MIL-STD-750D:1026 (1995) 45 PCS High Temperature Storage *Test Time= 1000hrs JEITA ED-4701:200 201 (2001) 45 PCS JEITA ED-4701:200 202 (2001) MIL-STD-750D:1051 (1995) MIL-STD-883G:1010 (2006) 5mins 30mins 5mins (CL=90%; LTPD=3%) *Test time: 200 Cycles JEITA ED-4701:100 105 (2001) JESD22-A104C (2005) 100 ± 5°C ～ -30°C ± 5°C Thermal Shock 15mins 15mins *Test time: 200 Cycles MIL-STD-750D:1056 (1995) 76 PCS MIL-STD-883G:1011 (2006) (CL=90%; LTPD=3%) MIL-STD-202G:107G (2002) JESD22-A106B (2004) (