LTW-Z5630SZL30

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only SMD LAMP LED OFFICE : 90 Chien I Road, Chung Ho Taipei, Taiwan, R.O.C. TEL : +886-2-2222-6181 FAX : +886-2-2226-5872 LTW-Z5630SZL30 DATASHEET DATE : 2012/08/08 REV. NO. : Version : A PAGE : BNS-OD-C131/A4 0 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * * * * * * Package in 8mm tape on 7" diameter reels. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. EIA STD package. I.C. compatible. Meet green product and Pb-free(According to RoHS) Package Dimensions Part No. Lens Color Source Color LTW-Z5630SZL30 Orange InGaN Blue Notes: 1. All dimensions are in millimeters. 2. Tolerance is ±0.2 mm (.008") unless otherwise noted. 3. Thermal pad and one of leads are connected and marked as ③, but without polarity. Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 1 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ℃ Absolute Maximum Ratings at Ta=25℃ Parameter Symbol Rating Unit Power Dissipation Po 576 mW Continuous Forward Current IF 150 mA Operating Temperature Range Topr -40 ~ +80 °C Storage Temperature Range Tstg -40 ~ +100 °C Tj ≦115 °C Junction Temperature Note: 1/10 duty cycle, Pulse width ≤100µs. Forbid to operating at reverse voltage condition for long. Suggestion IR Reflow Profile For Pb Free Process : IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B) Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 2 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electro-Optical Characteristics at Ta=25°C Parameter Forward Voltage Luminous Flux 1 Values Symbol VF Φv Min 3.0 Typ. 3.2 Max. 3.6 Min 30.5 Typ. 38.5 Max. 46.5 Test Condition Unit IF = 120mA V IF = 120mA lm Reverse Current IR Max. 100 VR = 5V µA Viewing Angle 2θ1/2 Typ. 120 IF = 120mA ° x Typ. 0.434 y Typ. 0.403 Optical Efficiency ηopt Typ. 100 IF = 120mA lm/W Correlated Color Temperature CCT Typ. 3000 IF = 120mA K Color Rendering Index CRI Min 80 IF = 120mA Chromaticity Coordinates IF = 120mA Notes 1. Luminous flux is the total luminous flux output as measured with an integrating sphere. 2. Iv (flux Φ v) classification code is marked on each packing bag. 3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram. 4. Caution in ESD: Static Electricity and surge damages the LED. It is recommended using a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. CAS140B is the test standard for the chromaticity coordinates (x, y) & Φv. 6. The chromaticity coordinates (x, y) guarantee should be added +/- 0.01 tolerance 7. CRI measurement allowance is ±5 Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 3 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List VF (in parallel) Spec. Table VF Bin Forward Voltage (volts) at IF = 120mA Min Max V1 3.0 3.1 V2 3.1 3.2 V3 3.2 3.3 V4 3.3 3.4 V5 3.4 3.5 V6 3.5 3.6 Tolerance on each Forward Voltage bin is +/- 0.1V Φ v Luminous Flux Spec. Table Φ v Bin Lumen (lm) at IF = 120mA Min Max R1 30.5 35.5 R2 35.5 40.5 R3 40.5 46.5 Tolerance on each Luminous Flux bin is +/- 7.5%. Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 4 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Color bin limits at IF = 120mA Hue Bin P1 P2 P3 P4 P5 P6 CIE 1931Chromaticity coordinates x 0.4386 0.4474 0.4562 0.4468 y 0.4048 0.4228 0.4260 0.4077 x 0.4298 0.4386 0.4468 0.4373 y 0.3867 0.4048 0.4077 0.3893 x 0.4305 0.4387 0.4474 0.4386 y 0.4019 0.4197 0.4228 0.4048 x 0.4222 0.4305 0.4386 0.4298 y 0.3840 0.4019 0.4048 0.3867 x 0.4223 0.4299 0.4387 0.4305 y 0.3990 0.4165 0.4197 0.4019 x 0.4147 0.4223 0.4305 0.4222 y 0.3814 0.3990 0.4019 0.3840 Tolerance on each Hue (x, y) bin is +/- 0.01. Hue Bin: 1931 CIE chromaticity 0.440 0.430 0.420 y-coordinate P1 P3 0.410 P5 0.400 P4 P2 P6 0.390 2850K 0.380 0.370 0.400 3250K 0.410 0.420 0.430 0.440 0.450 0.460 x-coordinate Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 5 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25°° C Ambient Temperature Unless Otherwise Noted) 180 1.0 Forward Current (mA) Relative Intensity 170 0.5 160 150 140 130 120 110 0.0 100 380 430 480 530 580 630 680 730 780 2.0 2.5 Wavelength (nm) Fig.1 Typical Spectrum 3.5 4.0 Fig.2 Forward Current vs Forward Voltage 160% 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 Relative Luminous Intensity Normalized at 90mA Relative Lumen Intensity 3.0 Forward Voltage (V) 5 15 25 35 45 55 65 75 85 Tj ('C) 140% 120% 100% 80% 60% 40% 20% 0% 100 110 120 130 140 150 160 170 180 Forward Current (mA) Figure Tj vs Relative Lumen Fig.3 Relative3.Luminous vs Junction Temperature Fig.4 Relative Luminous vs Forward Current Intensity 200 Forward Current (mA) Rth j-a = 75 °C/W 150 100 Rth j-a = 105 °C/W 50 0 0 20 40 60 80 100 Ambient Temperature ('C) Fig.5 Forward Current Derating Curve Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Fig.6 Spatial Distribution Page : 6 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only User Guide Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less than one minute. Recommend Printed Circuit Board Attachment Pad Infrared / vapor phase Reflow Soldering Package Dimensions of Tape Forward Current (mA) 200 160 120 80 40 0 0 20 40 60 80 100 Ambient Temperature Ta (C) Fig.5 Forward Current Derating Curve Note: 1. All dimensions are in millimeters (inches). Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 7 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-1000 pieces per reel. 3. Minimum packing quantity is 500 pieces for remainders. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with EIA-481-1-B specifications. Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 8 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing this moisture sensitive product is important to ensure the reliability of the product. The package is sealed: The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to solder process within 72hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the storage limiting time since opened, that we recommended to baking LEDs at 60°C at least 24hrs. To seal the remainder LEDs return to package, it’s recommended to be with workable desiccants in original package. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Wave Soldering Pre-heat 120~150°C Pre-heat time 120 sec. Max. Soldering Temp. 260°C Max. Soldering time 30 sec. Max. Pre-heat Pre-heat time Solder wave Soldering time Soldering iron 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Temperature Soldering time 300°C Max. 3 sec. Max. (one time only) 5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 9 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only



Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED’s plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or “no lightup” at low currents. To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. 7. Reliability Test Test Item Test Condition Note Number of Damaged Steady State Operating Life of High Temperature (HTOL) Ta=85℃, IF=120mA 1000 hrs 0/22 Steady State Operating Life of Low Temperature (LTOL) Ta=-40℃, IF=120mA 1000 hrs 0/22 Pulse Wet Operating Life of High Temperature (PWHTOL) 60℃/90%RH, IF=120mA 30mins ON/30min OFF 500 hrs 0/22 High Temperature Storage (HTS) 100℃ 1000 hrs 0/22 Low Temperature Storage (LTS) -40℃ 1000 hrs 0/22 Thermal Cycle (TC) -40℃~100℃ 30min dwell 5min transfer 200 cycle 0/22 Thermal Shock (TS) -40℃~100℃ 20min dwell 20sec transfer 200 cycle 0/22 Solder Resistance (SR) 265℃, 3X MSL 5sec 0/22 Solder Ability (SA) 245℃5sec, 95% coverage 5sec 0/11 Mechanical Shock (MS) 1500G 0.5msec pulse shock each 6 axis 0/6 Random Vibration (RV) 6G RMS, 10-2000Hz, 10min per axis 0/6 Variable Vibration Frequency (VVF) 10-2000-10Hz, log or linear sweep rate, 20G for 1 min, 1.5mm each apply 3x per axis over 6hrs 0/6 Salt Spread (SS) 35℃, 30g/m2/day 48hrs 0/11 Item Lumen Shift Voltage Shit CIE X, Y Shift Criteria for Judgement Over -30% Within ±10% Within ±0.01 Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 10 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8. Others The appearance and specifications of the product may be modified for improvement without prior notice. 9. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTW-Z5630SZL30 BNS-OD-C131/A4 Page : 11 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Rename item list Version Page A - Content of Change Official 5630 Spec for lighting application (3000K) Date Record 08/08, 2012