B1101UC4LXX

SIDACtor ® Protection Thyristors SLIC Protection Battrax® Series - Dual Port Negative - MS-013 Description The Dual Port Negative Battrax® Series are programmable SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. Dual port protection is provided by a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Dual-port protection Gate trigger tracking device Integrated diode for positive voltage surges Does not degrade with use Fails short circuit when surged in excess of ratings Applicable Global Standards TIA-968-A Pinout Designation 1 2 3 6 5 4 GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 TIA-968-B ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building Schematic Symbol (T1) 1 6 (T2) 5 Ground (-VREF) 2 (R1) 3 4 (R2) Electrical Characteristics VDRM @lDRM=5μA V min B1101UC4Lxx B1161UC4Lxx B1201UC4Lxx B1101UC4 B1161UC4 B1201UC4 I-VREF I-VREF I-VREF VS @100V/μs V max I-VREF I-VREF I-VREF IH IS IT A max 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 VF V max 5 5 5 Capacitance* pF min pF max 30 30 30 200 200 200 Part Number Marking mA min mA max 100 160 200 100 100 100 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1 & 6) to Ground (pin 5) and Ring (pin 3 & 4) to Ground (pin 5) - VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). * Off-state capacitance (CO) is measured across pins 1 & 5, 3 & 5, 4 & 5, and 6 & 5 at 1 MHz with a 2V bias. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 126 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings IPP Series 0.2x310 0.5x700 2 1 ITSM 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 50/60 Hz A min 50 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 150 di/dt A/μs max 500 A min C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 500 A min 400 A min 200 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. rating assumes VREF - IPP PP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Modified MS-013 6 5 4 1 2 3 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 60 °C/W V-I Characteristics +I V tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP 100 VREF VS VDRM -V IDRM IH IS IT IPP PIN 5 CONNECTED TO GROUND Pin 1-2: PIN 2 CONNECTED TO VREF PIN 2 CONNECTED TO GROUND Peak Value tr = r ise time to peak value td = decay time to half value VT IF Waveform = tr x td +V 50 Half Value 0 0 tr td t – Time (μs) -I PIN 3 CONNECTED TO VREF Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 14 2.0 Percent of VS Change – % 10 IH (TC = 25ºC) 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 6 4 2 0 -4 -6 -8 -40 -20 0 IH 8 25 °C 25°C 20 40 60 80 100 120 140 160 Ratio of Junction Temperature (TJ) – °C Case Temperature (TC) - ºC © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 127 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) TL TS(max) Preheat 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VDC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking B1 xx 1 U C 4 L xx TYPE B1: Negative Battrax SIDACtor PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE PACKAGE TYPE RoHS COMPLIANT DUAL PORT IPP RATING Date Code © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 128 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters). Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 --0.143 Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 --3.63 7º TYP A D 7º TYP G A J H Burr Side 96º 4º 7º TYP B A F 7º TYP MIN Length of Flat K Detail A Mold Split Line BSC* A B C D E F G H J K BSC* * BSC = Basic Spacing between Centers Packing Options Package Type Description Modified MS-013 6-pin Tape and Reel Pack Quantity Added Suffix Industry Standard 1500 500 (50 per tube) RP TP EIA-481-D N/A U Modified MS-013 6-pin Tube Pack Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .512 (13.0) Arbor Hole Dia. .472 (12.0) 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .110 (2.79) .045 (1.14) 90˚ .165 (4.19) .310 (7.87) 6 Interior of the Tube 20.000 ± .030 (508.00 ± 0.76) .005 A .150 (3.81) .225 (5.72) .525 (13.34) A Dimensions are in inches (and millimeters) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 129 Revised: February 22, 2011