P0641SCLRP

SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Series - DO-214 Description Fixed Voltage Series DO-214 are uni-directional SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single line protection using a fixed voltage switching device for negative surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits Low voltage overshoot Agency Approvals Agency Agency File Number E133083 Low on-state voltage Does not degrade with use Applicable Global Standards TIA-968-A TIA-968-B Indicates cathode ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building* *A-rated parts require series resistance Fails short circuit when surged in excess of ratings Integrated diode for positive voltage surges Pinout Designation GR 1089 Intra-building* IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol (T/R) (G) Electrical Characteristics VDRM @lDRM=5μA V min P0641SALRP P0721SALRP P0901SALRP P1101SALRP P1301SALRP P1701SALRP P0641SCLRP P0721SCLRP P0901SCLRP P1101SCLRP P1301SCLRP P1701SCLRP P61A P71A P91A P01A P131A P17A P61C P71C P91C P01C P131C P17C 58 65 75 95 120 160 58 65 75 95 120 160 VS @100V/μs V max 77 88 98 130 160 200 77 88 98 130 160 200 IH mA min 120 120 120 120 120 120 120 120 120 120 120 120 IS mA max 800 800 800 800 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 VF V max 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, -2V bias pF pF min 50 45 45 40 40 30 65 60 60 50 50 40 pF max 90 85 80 70 70 55 200 190 180 160 160 130 Part Number Marking Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 89 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings IPP Series 0.2x310 0.5x700 2 1 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 50 150 5x320 1 9x720 2 A min 75 200 10x360 1 10x360 2 A min 75 175 10x1000 1 10x1000 2 A min 45 100 5x310 1 10x700 2 A min 75 200 ITSM 50/60 Hz A min 20 30 di/dt A/μs max 500 500 A min A C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 150 500 A min 150 400 A min 90 200 20 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package DO-214AA Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit °C °C °C/W V-I Characteristics +I VF tr x td Pulse Waveform tr = r ise time to peak value td = decay time to half value IPP – Peak Pulse Current – %IPP 100 Peak Value VS VDRM -V VT +V Waveform = tr x td IDRM IH IS IT -I 50 Half Value 0 0 tr td t – Time (μs) Normalized VS Change vs. Junction Temperature 14 12 10 Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change – % IH (TC = 25ºC) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 6 4 2 0 -4 -6 -8 -40 -20 0 IH 8 25 °C 25°C 20 40 60 80 100 120 140 160 Ratio of Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Case Temperature (TC) - ºC 90 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 3°C/sec. Max. 60-150 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking P xxx 1 S X L RP DEVICE TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK L: RoHS COMPLIANT IPP RATING Cathode Indicator XXXXX XXXXX Part number code (refer to Electrical Characteristics table) Date code © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 91 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — DO-214AA Cathode Indicator B D Case Temperature Measurement Point Dimensions A Inches Min 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 Millimeters Min 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 Max 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 Max 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 CA B C D E F G G H E 0.079 (2.0) F K H K 0.110 (2.8) 0.079 (2.0) Dimensions are in inches (and millimeters). Pad Outline (MM) Packing Options Package Type S Description DO-214AA Tape & Reel Pack Quantity 2500 Added Suffix RP Industry Standard EIA-481-D Tape and Reel Specification — DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 12.99 (330.0) 0.059 DIA (1.5) Cover tape Cathode 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 92 Revised: February 22, 2011