P1100GALRP

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - DO-15 Description The SIDACtor Series DO-15 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a cost-effective through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Does not degrade with use Fails short circuit when surged in excess of ratings Low Capacitance Applicable Global Standards TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level GR 1089 Inter-building* * A/B-rated parts require series resistance Pinout Designation Not Applicable Schematic Symbol GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Electrical Characteristics VDRM @lDRM=5μA V min 90 120 140 170 190 220 275 320 90 120 140 170 190 220 275 320 VS @100V/μs V max 130 160 180 220 260 300 350 400 130 160 180 220 260 300 350 400 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, 2V bias pF min 30 25 25 25 25 25 20 20 30 25 25 25 25 25 20 20 pF max 60 40 40 40 30 30 30 30 60 40 40 40 30 30 30 30 Part Number P1100GALRP P1300GALRP P1500GALRP P1800GALRP P2300GALRP P2600GALRP P3100GALRP P3500GALRP P1100GBLRP P1300GBLRP P1500GBLRP P1800GBLRP P2300GBLRP P2600GBLRP P3100GBLRP P3500GBLRP Marking P11A P13A P15A P18A P23A P26A P31A P35A P11B P13B P15B P18B P23B P26B P31B P35B mA min mA max 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 163 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings IPP Series 10x560 10x560 2 1 ITSM 10x1000 10x1000 2 1 50 / 60 Hz Amps min 20 25 Amps min A B Notes: Amps min 45 80 50 100 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package DO-15 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 60 Value Unit °C °C °C/W Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 164 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Part Marking Part Marking Code (Refer to Electrical Characteristics Table) Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Pxxxx XXXXX Date Code Part Numbering Moisture Sensitivity Level P xxx 0 G x L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT IPP RATING Packing Options Package Type G Description DO-15 Axial Tape & Reel Quantity 5000 Added Suffix RP Industry Standard EIA-RS296-D Dimensions — DO-15 Dimension B Inches MIN 0.028 0.12 0.235 1 MAX 0.034 0.14 0.27 Millimeters MIN 0.711 3.048 5.969 25.4 MAX 0.864 3.556 6.858 D B D G L L G L Tape and Reel Specification — DO-15 Symbols Spacing off center, either side 0.039 (1.0) Description Component Spacing (lead to lead) Inner Tape Pitch Tape Width Max. Off Alignment Reel Dimension Max. Hub Recess Max. Abor Hole Inches MM 5.08 ± 0.508 52.37 ± 1.498 6.35 1.219 330.2 76.19 17 .27 2.55 (64.8) B TYP A B C D E F G A C D E Dimensions are in inches (and millimeters). 3.15 (80.0) TYP recess depth max 0.75” G F Direction of Feed 165 Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.