P1101UCLXX

SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Multiport Series - MS-013 Description Fixed Voltage Multiport Series MS-013 are SIDACtor® devices designed to protect sensitive SLIC (Subscriber Line Interface Circuit) devices from damaging overvoltage transients. The series provides a high surge current rated dual port protection solution incorporating a fixed voltage switching threshold for negatives surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits Agency Approvals Agency Agency File Number E133083 Low voltage overshoot Low on-state voltage Does not degrade with use Fails short circuit when surged in excess of ratings 6 5 4 Two-port protection Integrated diodes for positive voltage surges Replaces four discrete devices Pinout Designation 1 2 3 Applicable Global Standards TIA-968-A ITU K.20/21 Enhanced Level* GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol 1 (T1) 2 (G1) 3 (R1) 6 (T2) 5 (G2) 4 (R2) ITU K.20/21 Basic Level GR 1089 Inter-building* *A-rated parts require series resistance Electrical Characteristics VDRM @lDRM=5μA V min P0641UALxx P0721UALxx P0901UALxx P1101UALxx P1301UALxx P1701UALxx P0641UCLxx P0721UCLxx P0901UCLxx P1101UCLxx P1301UCLxx P1701UCLxx P0641UA P0721UA P0901UA P1101UA P1301UA P1701UA P0641UC P0721UC P0901UC P1101UC P1301UC P1701UC 58 65 75 95 120 160 58 65 75 95 120 160 VS @100V/μs V max 77 88 98 130 160 200 77 88 98 130 160 200 IH mA min 120 120 120 120 120 120 120 120 120 120 120 120 IS mA max 800 800 800 800 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 VF V max 5 5 5 5 5 5 5 5 5 5 5 5 Part Number Marking Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pins 1 & 6) to Ground (pins 2 & 5), and Ring (pins 3 & 4) to Ground (pins 2 & 5) - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 109 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1-2 / 3-2 (4.5/6.5) Tip-Ground, Ring-Ground MIN MAX 50 45 40 40 35 30 65 60 60 50 35 40 205 195 180 160 160 125 205 195 180 160 160 125 pF Pin 1-3 (4.6) Tip-Ring MIN MAX 30 20 20 15 15 15 40 20 20 15 15 15 135 125 115 105 100 80 130 125 115 105 100 80 Part Number P0641UALxx P0721UALxx P0901UALxx P1101UALxx P1301UALxx P1701UALxx P0641UCLxx P0721UCLxx P0901UCLxx P1101UCLxx P1301UCLxx P1701UCLxx Note: Off-state capacitance (CO) is measured at 1 MHz with a -2V bias. Surge Ratings IPP Series 0.2x310 0.5x700 2 1 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 50 150 5x320 1 9x720 2 A min 75 200 10x360 1 10x360 2 A min 75 175 10x1000 1 10x1000 2 A min 45 100 5x310 1 10x700 2 A min 75 200 ITSM 50/60 Hz A min 20 30 di/dt A/μs max 500 500 A min A C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 150 500 A min 150 400 A min 90 200 20 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Modified MS-013 6 5 4 1 2 3 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 60 °C/W © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 110 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection V-I Characteristics +I VF tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td VS VDRM -V VT +V IDRM IH IS IT -I 50 Half Value 0 0 tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 14 Percent of VS Change – % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Junction Temperature (TJ) – °C Ratio of Case Temperature (TC) - ºC © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 111 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 3°C/sec. Max. 60-150 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VDC 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Temp Cycling Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking P xxx1 U x L xx TYPE P=SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS RoHS COMPLIANT IPP RATING XXXXXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 112 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters). Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 0.143 Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 3.63 7º TYP A D 7º TYP G A J H Burr Side 96º 4º 7º TYP B A F 7º TYP MIN Length of Flat K Detail A Mold Split Line BSC* A B C D E F G H J K BSC* * BSC = Basic Spacing between Centers Packing Options Package Type Description Quantity Added Suffix Industry Standard U Modified MS-013 6-pin Tape and Reel Pack Modified MS-013 6-pin Tube Pack 1500 500 (50 per tube) RP TP EIA-481-D N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .512 (13.0) Arbor Hole Dia. .472 (12.0) 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Dimensions — MS-013 Message Location .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .110 (2.79) .045 (1.14) 90˚ .165 (4.19) .310 (7.87) 6 Interior of the Tube 20.000 ± .030 (508.00 ± 0.76) .005 A .150 (3.81) .225 (5.72) .525 (13.34) A Dimensions are in inches (and millimeters) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 113 Revised: February 22, 2011