961-20A0-011

Echotel ® Model 961/962 Ultrasonic Level Switches DESCRIPTION Increasing demands for compliance with safety systems and overfill protection has mandated more reliable point level measurement. Echotel® Models 961 & 962 Ultrasonic Level Switches meet these demands with advanced transducer designs, extensive hazardous location approvals, and a new self-test technology. Model 961 offers the ultimate solution to reliable single point liquid level measurement. This advanced switch uses pulsed signal technology for superior performance in difficult process conditions, and to provide excellent immunity from sources of electrical noise interference. Extensive self-testing of the electronics and transducer make this advanced switch suitable for use in Safety Integrity Level (SIL) 2 loops. Model 961 Model 962 is a dual point switch that can be used as a level controller, or to control pumps in an auto fill or auto empty mode. The tip sensitive lower gap performs well in aerated or foamy liquids, and can measure to within 1⁄4" of the vessel bottom. The rigidity of the unique flow-through upper gap allows separations of up to 128" (325 cm) between the upper and lower transducer gaps. Model 962 APPLICATIONS • High level alarm • Low level alarm FEATURES • Single or dual point liquid level measurement • Advanced self-test technology provides unsurpassed testing of electronics, transducer, piezoelectric crystals, and electromagnetic noise • Adjustable time delay for turbulent aerated liquids • Relay output or mA current shift with separate malfunction indication • Integral or remote mount electronics • Pulsed signal technology • Extensive FM, CSA, and ATEX explosion proof and intrinsically safe approvals • Suitable for Safety Integrity Level (SIL) 2 loops • Overfill protection • Pump protection • Seal pot level • Pump control INDUSTRIES • Chemical • Petrochemical • Pulp and paper • Food and pharmaceutical • Power • Water and wastewater TECHNOLOGY BASIC OPERATION Model 961/962 switches utilize ultrasonic energy to detect the presence or absence of liquid in a single or dual point transducer. Ultrasonic contact level technology uses highfrequency sound waves that are easily transmitted across a transducer gap in the presence of a liquid media, but are attenuated when the gap is dry. Model 961/962 switches use an ultrasonic frequency of 2 MHz to perform this liquid level measurement in a wide variety of process media and application conditions. The transducer uses a pair of piezoelectric crystals that are encapsulated in epoxy at the tip of the transducer. The crystals are made of a ceramic material that vibrates at a given frequency when subjected to an applied voltage. The transmit crystal converts the applied voltage from the electronics into an ultrasonic signal. When liquid is present in the gap, the receive crystal senses the ultrasonic signal from the transmit crystal and converts it back to an electrical signal. This signal is sent to the electronics to indicate the presence of liquid in the transducer gap. When there is no liquid present, the ultrasonic signal is attenuated and is not detected by the receive crystal. Ultrasonic transducer Transmit crystal Receive crystal Ultrasonic signal transmission across transducer gap PULSED SIGNAL TECHNOLOGY gap is dry. This technology also provides excellent immunity from electromagnetic noise interference. Pulsed signal technology makes the 961/962 units more reliable than older continuous wave ultrasonic switches. Unlike many tuning forks, pulsed signal ultrasonic switches do not need to be configured for different media densities, making these units the most universally applied level switches on the market today. Challenging process conditions such as aeration, suspended solids, and high viscosities are easily handled with the pulsed signal technology utilized in the 961/962 switches. Pulsed signal circuitry drives the transmit piezoelectric crystal to produce powerful pulses of high-frequency ultrasonic energy. These ultrasonic pulses are readily transmitted through liquids, but are attenuated when the transducer SAFETY INTEGRITY LEVEL (SIL) Critical process control applications demand reliable instruments that provide high levels of safety. The introduction of standards such as IEC 61508, IEC 61511 and ISA 84, have generated interest in using Safety Instrumented Systems (SIS) as a means to define the reliability of instruments in a control loop. All 961 Relay 2 as 1oo1 92.0% 1.77E-04 versions of the Model 961/962 switches undergo a detailed performance evaluation called a Failure Modes, Effects and Diagnostics Analysis (FMEDA). Three key components of the FMEDA are the Safety Integrity Level (SIL), Safe Failure Fraction (SFF) and the average Probability of Failure on Demand (PFDavg). 961 Current Shift 2 as 1oo1 91.4% 1.61E-04 962 Relay 2 as 1oo1 91.5% 2.31E-04 962 Current Shift 2 as 1oo1 91.8% 1.87E-04 SIL SFF PFDavg 2 ADVANCED SELF-TEST AND DIAGNOSTICS Ultrasonic switches are often used as the last means of detecting whether a cer Transdu ls process vessel will overflow and cause a sta & cry ics spill of potentially hazardous liquids, or Electron e empty out and possibly cavitate the Nois pumps. In these critical applications it is desirable to have a method of periodically testing the ultrasonic switch to ensure that it is functioning properly. Model 961/962 switches feature an advanced self-test technology that not only tests the electronics, transducer, and piezoelectric crystals, but also tests for the presence of industrial sources of environmental noise. Should the switch detect any problems a malfunction output is generated to alarm the user, and a red LED is lit to indicate an alarm condition. Self-test is performed automatically and continuously several times per second to verify proper operation of 961/962 switches. In addition, a pushbutton is provided to initiate a manual self-test mode. Pressing this test button stops all transmit pulses, which simulates an electronics failure. This failure is reported as: • 3.6 or 22 mA (selectable) with current shift output units • SPDT malfunction relay de-energizes with relay output units Taking diagnostics one step further is the unique noise self-test mode feature that is standard in all 961/962 switches. This tests for electromagnetic and acoustical noise that can influence many instrumentation technologies. If high levels of environmental noise are detected, the electronics reports a fault condition to alert the user of potential instrumentation reliability concerns. A microprocessor in the 961/962 electronics continuously monitors all self-test data. Should a fault occur, the microprocessor can determine whether the malfunction is due to the electronics, transducer, piezoelectric crystals, or the presence of environmental noise. A pushbutton and Fault LED is used to assist in troubleshooting the switch: 5 One flash of the Fault LED indicates a problem with the transducer or piezoelectric crystals 55 Two flashes of the Fault LED indicates a problem with one of the electronics boards 555 Three flashes of the Fault LED indicates excessive levels of environmental noise ADJUSTABLE TIME DELAY A potentiometer allows a 1⁄2 to 45 second delay to be set to disregard waves or splashes, and reliably detect the true liquid level. Turbulence and splashing can cause some fixed time response switches to produce false level alarms. Model 961/962 switches overcome this difficulty with an adjustable time delay feature. RELIABLE TRANSDUCER DESIGN Model 961 single point has a tip-sensitive transducer with an arch-shaped gap for superior performance in aerated or foamy liquids. Dual point Model 962 features a tip sensitive lower gap and flow through upper gap. This robust design allows separations of 125 inches (318 cm) between the upper and lower transducer gaps. Dependable point level measurement begins with reliable sensor design. Over 30 years of ultrasonic level switch technology experience is behind the Model 961/962 single and dual gap transducers. The result is an extremely robust transducer design that offers superior performance in difficult process conditions. 3 APPLICATIONS TYPICAL High Alarm Model 961 single point switches may be used for high or low level alarm, as well as for pump protection. The Model 962 dual point unit is typically configured to measure high/low, high/high, or low/low levels. The single point 961 can be mounted vertically or horizontally in vessels, bridles, or pipes. The dual gap 962 is always top mounted. A broad selection of transducer materials allow the 961/962 to be used in a wide variety of process media. Metallic transducers include 316 SS, Hastelloy® C, and Monel®. The 316 SS transducer has a NACE construction option for sour gas service, and can also be built per ASME B31.1 and B31.3 piping codes. Thermoplastic transducers include Kynar® and CPVC. These corrosion resistant plastic transducers feature a stiffening tube that runs the length of the transducer for extra rigidity. Kynar-faced 316 SS flange options are offered with the Kynar transducers. Fill Line Dual Point Alarm Pump Protection Low Alarm PUMP CONTROL A DIP switch on the Model 962 allows it to be configured to control level, or to function as a pump controller. In the pump control mode the unit can perform auto fill or auto empty of tanks, sumps, or wet wells. The tip sensitive lower gap allows liquid levels to be pumped down to within 1⁄4" from the bottom of the vessel. The rigidity of the flow through upper gap allows the 962 to be used even when sumps experience severe turbulence from vessel fill lines. HYGIENIC Spray Ball The hygienic version of the Model 961 features a deep drawn stainless steel electronics housing. Tri-Clamp® and DN65 Varivent hygienic process connections are offered for use in food & beverage, pharmaceutical, and biotechnology applications. These hygienic transducers have 3-A (Authorization #596), EHEDG certification (per TNO Report # V4772/01) and a 20 R a finish to provide a uniform and ultra-smooth surface that inhibits microbial growth. Electron beam welding technology is utilized to facilitate a crevice-free surface inside the transducer tip. This allows these transducers to be used in a wide variety of hygienic applications where CIP (Clean-in-Place) is used to remove any contamination from the transducer surface. 4 ELECTRONICS MODEL 961/962 SPECIFICATIONS WITH RELAY OUTPUT Supply Voltage Relay Outputs Relay Ratings Fail-safe Power Consumption Ambient Temperature 961: 962: DPDT: SPDT: 961/962: 18 to 32 VDC, or 102 to 265 VAC, 50/60 Hz One DPDT level relay and one SPDT malfunction relay Two SPDT level relays and one SPDT malfunction relay 5 amps @ 120 VAC, 250 VAC, and 30 VDC, 0.4 amp @ 110 VDC 5 amps @ 120 VAC, 250 VAC, and 30 VDC, 0.15 amp @ 125 VDC Selectable for high or low level Less than 3 watts -40° to +160° F (-40° to +70° C) MODEL 961/962 WITH CURRENT SHIFT OUTPUT Supply Voltage Current Shift Output 961: 962: 961/962: Loop Resistance Fail-safe Power Consumption Ambient Temperature 961/962 11 to 35 VDC 8 mA normal operation, 16 mA level alarm (±1 mA) 8 mA normal operation, 12 mA lower gap alarm, 16 mA upper gap alarm (±1 mA) 3.6 mA or 22 mA selectable fault signal (±1 mA) 104 ohms with 11 VDC input, 1100 ohms with 35 VDC input Selectable for high or low level Less than 1 watt -40° to +160° F (-40° to +70° C) TRANSDUCER MODEL 9A1/9M1 SPECIFICATIONS SINGLE POINT Maximum Pressure 2000 psi (138 bar) 1500 psi (103 bar) 2000 psi (138 bar) 1500 psi (103 bar) 1200 psi (83 bar) see graph below see graph below Actuation Length 1" and 2" (3 and 5 cm) 3" to 130" (6 to 330 cm) 1" and 2" (3 and 5 cm) 3" to 130" (6 to 330 cm) 1" to 130" (3 to 330 cm) 2" to 130" (5 to 330 cm) 1" to 130" (3 to 330 cm) Transducer Material 316 Stainless Steel 316 Stainless Steel Hastelloy C-276 Hastelloy C-276 Monel Kynar CPVC Material Code (page 10) A*, S, N, K A*, S, N, K B B C R P Operating Temperature Range -40° to +325° F (-40° to +163° C) -40° to +325° F (-40° to +163° C) -40° to +325° F (-40° to +163° C) -40° to +325° F (-40° to +163° C) -40° to +325° F (-40° to +163° C) -40° to +250° F (-40° to +121° C) -40° to +180° F (-40° to +82° C) * Material Code “A” has a Cryogenic Trandsucer Option for -110° to +250° F (-80° to +120° C) operating temperature range MODEL 9A2/9M2 DUAL POINT Maximum Pressure 1500 psi (103 bar) see graph below Actuation Length 5" to 130" (13 to 330 cm) 5" to 130" (13 to 330 cm) Transducer Material 316 Stainless Steel CPVC Material Code (see page 10) A, K P Operating Temperature Range -40° to +325° F (-40° to +163° C) -40° to +180° F (-40° to +82° C) Kynar Transducer Ratings 300 250 Pressure (bar) Pressure (psi) 200 150 100 50 0 -40 0 60 120 180 240 Temperature (°F) 30 25 20 15 10 5 0 -40 0 40 80 120 Temperature (°C) Pressure (psi) 300 250 200 150 100 50 0 -40 0 CPVC Transducer Ratings 30 25 Pressure (bar) 20 15 10 5 40 80 120 160 200 Temperature (°F) 0 -40 0 40 80 120 Temperature (°C) Range with " NPT Range with 150# flange Range with PN16 flange 5 PERFORMANCE Repeatability Response Time Time Delay Self-Test SPECIFICATIONS Automatic: Manual: Shock Class Vibration Class Humidity Electromagnetic Compatibility ±0.078" (2 mm) 1 ⁄2 second typical Variable 0.5 – 45 seconds on rising and falling levels Continuously verifies operation of electronics, transducer, piezoelectric crystals, and electrical noise Push button verifies operation of electronics, transducer, and piezoelectric crystals ANSI/ISA-S71.03 Class SA1 ANSI/ISA-S71.03 Class VC2 0 – 99%, non-condensing Meets CE requirements EN 61326 PHYSICAL Housing Material Cable Entry Gross Weight SPECIFICATIONS Cast aluminum A356-T6, cast 316 stainless steel, or deep drawn 304 stainless steel (hygienic housing) Dual 3⁄4" NPT, or M20 connections (one end is plugged) 961/962 Electronics: 2" (5 cm) Transducer: 2.2 lbs. (1.0 kg) 0.6 lbs. (0.3 kg) DIMENSIONAL INCHES (mm) SPECIFICATIONS 5.24 (133) 4.00 (102) 4.00 (102) 4.43 (113) 5.75 (146) 4.43 (113) 1.05 (26) Typical 2.35 (60) Typical 1.8 (46) Typical Actuation length for Tri-Clamp fitting Actuation length for NPT connection Actuation length for ANSI flange 0.25 (6) ∅ .875 (22) 0.25 (6) ∅ .875 (22) 0.25 (6) ∅ .875 (22) Model 961 with Hygienic Housing with Tri-Clamp® 16-AMP Fitting Model 961 with Cast Aluminum Housing with NPT Connection Model 961 with Cast Stainless Steel Housing and ANSI Flange 6 DIMENSIONAL INCHES (mm) SPECIFICATIONS 4.00 (102) 4.00 (102) 3.95 (100) 4.43 (113) 1.8 (46) Typical 2.75 (70) 3.00 (76) 3.50 (89) ¾" NPT Conduit Connection 0.25 (6) ∅ .875 (22) Actuation length for NPT connection 2 Holes .38 (10) dia. 2.00 (51) Model 961/962 with Remote Electronics Remote Transducer with NPT Connection 4.00 (102) 4.00 (102) 4.43 (113) 4.43 (113) 1.8 (46) Typical 2.35 (60) Typical Actuation length B Actuation length B Actuation length A Actuation length A 0.25 (6) ∅ .875 (22) Dia. 0.25 (6) ∅ .875 (22) Dia. Model 962 with NPT Connection Model 962 with ANSI Flange 7 MODEL 961/962 NUMBER ELECTRONICS Models available for quick shipment, usually within one week after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP) BASIC MODEL NUMBER 961 962 Single-point electronics Dual-point electronics INPUT POWER 2 5 7 18 to 32 VDC line-powered 11 to 35 VDC loop-powered 102 to 265 VAC line-powered OUTPUT SIGNAL 0 D mA current shift (available with Input Power code 5) 5-amp gold flash relays (available with Input Power codes 2 or 7) HOUSING COVER 0 1 Standard housing cover Glass window cover (available with Electronics Housing codes 0, 1, 4 or 5) MOUNTING 0 1 Integral Remote (requires Connecting Cable from page 11) AGENCY APPROVAL 1 FM/CSA Intrinsically safe, Non-Incendive & Explosion Proof * (use with current shift Output Signal code 0) FM/CSA Explosion Proof & Non-Incendive (use with relay Output Signal code D, and Electronics Housing codes 0, 1, 2 & 3) FM/CSA Non-incendive (available with Output Signal codes 0 & D and Electronics Housing codes 4 & 5) ATEX II 1G EEx ia IIC T5, Intrinsically safe (use with Output Signal code 0, and Electronics Housing codes 0, 1, 2, 3) ATEX II 1/2G EEx d IIC T6, Flameproof (use with Output Signal code 0 or D, and Electronics Housing codes 0, 1, 2, 3) 3 7 A C * Explosion Proof approvals not available with housing codes 4 & 5 ELECTRONICS HOUSING 0 1 2 3 4 5 Cast aluminum with 3⁄4" NPT dual conduit entries Cast aluminum with M20 dual conduit entries Cast SS with 3⁄4" NPT dual conduit entries Cast SS with M20 dual conduit entries Deep drawn SS with 1⁄2" NPT dual conduit entries Deep drawn SS with M20 dual conduit entries 9 8 6 A MODEL 961 NUMBER POINT TRANSDUCER Models available for quick shipment, usually within one week after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP) SINGLE TRANSDUCER UNIT OF LENGTH A M English (length in inches) Metric (length in centimeters) MATERIALS OF CONSTRUCTION A S B C R P N K 316/316L stainless steel 316/316L with 20 Ra hygienic finish (use only with Process Connection codes 3T, 4T, or VV) Hastelloy C-276 Monel Kynar* (use only with Process Connection codes 11, 23, 33, 43, BA, CA, DA) CPVC (use only with Process Connection codes 11, 23, 33, 43, BA, CA, DA) 316/316L stainless steel, NACE construction 316/316L stainless steel, ASME B31.1 &B31.3 construction * Flanged Kynar transducers have Kynar faced 316 stainless steel flanges PROCESS CONNECTIONS THREADED CONNECTIONS 11 21 22 ⁄4" NPT 1" NPT 1" BSP (G1) 3 HYGIENIC CONNECTIONS 3T 4T VV 11⁄2" Tri-Clamp® 16 AMP fitting 2" Tri-Clamp® 16 AMP fitting DN65 – Varivent® Type N ANSI RAISED FACE FLANGES 23 24 25 33 34 35 43 44 45 1" 150# ANSI RF flange 1" 300# ANSI RF flange 1" 600# ANSI RF flange 11⁄2" 150# ANSI RF flange 11⁄2" 300# ANSI RF flange 11⁄2" 600# ANSI RF flange 2" 150# ANSI RF flange 2" 300# ANSI RF flange 2" 600# ANSI RF flange EN/DIN FLANGES BA BB BC CA CB CC DA DB DD DE DN DN DN DN DN DN DN DN DN DN 25 25 25 40 40 40 50 50 50 50 PN PN PN PN PN PN PN PN PN PN 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63/100 EN 1092-1 Type B2 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63/100 EN 1092-1 Type B2 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63 EN 1092-1 Type B2 100 EN 1092-1 Type B2 TRANSDUCER OPTIONS A C Standard design Cryogenic design to -110° F (-80° C) (available with Materials code A) ACTUATION LENGTH* (unit of length specified in second digit) 1" to 130" in 1" increments (Example: 4 inches = 004) 1" minimum for NPT process connections 2" minimum for BSP, hygienic, and flanged process connections 2" minimum for all Kynar transducers Available English ESP lengths: 1", 2", 4", 6", 8", 12" 3 cm to 330 cm in 1 cm increments (Example: 6 centimeters = 006) 3 cm minimum for NPT process connections 5 cm minimum for BSP, hygienic, and flanged process connections 5 cm minimum for all Kynar transducers Available metric ESP lengths: 3, 5, 10, 30 cm * For lengths longer than 130" (330 cm), contact the factory 9 1 9 MODEL 962 DUAL NUMBER POINT TRANSDUCER TRANSDUCER UNIT OF LENGTH A M English (length in inches) Metric (length in centimeters) MATERIALS OF CONSTRUCTION A K P 316/316L stainless steel 316/316L stainless steel, ASME B31.1 &B31.3 construction CPVC (use only with Process Connection codes 11, 23, 33, 43, BA, CA, DA) PROCESS CONNECTIONS THREADED CONNECTIONS 11 21 22 ⁄4" NPT 1" NPT 1" BSP (G1) 3 ANSI RAISED FACE FLANGES 23 24 25 33 34 35 43 44 45 1" 150# ANSI RF flange 1" 300# ANSI RF flange 1" 600# ANSI RF flange 11⁄2" 150# ANSI RF flange 11⁄2" 300# ANSI RF flange 11⁄2" 600# ANSI RF flange 2" 150# ANSI RF flange 2" 300# ANSI RF flange 2" 600# ANSI RF flange EN/DIN FLANGES BA BB BC CA CB CC DA DB DD DE DN DN DN DN DN DN DN DN DN DN 25 25 25 40 40 40 50 50 50 50 PN PN PN PN PN PN PN PN PN PN 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63/100 EN 1092-1 Type B2 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63/100 EN 1092-1 Type B2 16 EN 1092-1 Type A 25/40 EN 1092-1 Type A 63 EN 1092-1 Type B2 100 EN 1092-1 Type B2 Important: Use the “A” dimension as the actuation length code. The “B” dimension must also be specified in quote/order. Example: For a 962 with an “A” dimension of 18" and a “B” dimension of 7", specify actuation length code 018. Actuation length B min. 2" (5 cm) Actuation length A Minimum distance between actuation points A and B is 3" (8 cm) Maximum distance between actuation points A and B is 125" (318 cm) “A” DIMENSION ACTUATION LENGTH* (units specified in second digit) 5" to 130" in 1" increments 5" minimum for NPT process connections 6" minimum for BSP, and flanged process connections Example: 5 inches = 005 13 cm to 330 cm in 1 cm increments 13 cm minimum for NPT process connections 15 cm minimum for BSP, and flanged process connections Example: 13 centimeters = 013 * For lengths longer than 130" (330 cm), contact the factory 9 10 2 A MODEL NUMBER CABLE CONNECTING ELECTRONICS MODEL 6 7 Remote cable for Model 961 Remote cable for Model 962 CONNECTING CABLE LENGTH (FEET) Maximum Length: 150 feet Example: 12 feet = 012 Minimum Length: 10 feet 0 3 7 3 3 1 AGENCY AGENCY APPROVALS PROTECTION METHOD AREA CLASSIFICATION APPROVED MODELS FM & CSA 96X-X0A0-X10 96X-X0A0-X11 96X-X0A0-X12 96X-X0A0-X13 96X-X0A1-X10 96X-X0A1-X11 96X-XDA0-X30 96X-XDA0-X31 96X-XDA0-X32 96X-XDA0-X33 96X-XDA1-X30 96X-XDA1-X31 with transducers 9AX-XXXX-XXX or 9MX-XXXX-XXX 96X-XXAX-XXX or with transducers 9AX-XXXX-XXX or 9MX-XXXX-XXX 96X-50AX-X1X with transducers 9AX-XXXX-XXX or 9MX-XXXX-XXX Explosion Proof Class I, Div. 1,Groups B, C, & D Class II, Div. 1, Groups E, F, & G Class III, Type 4X, IP 66, T6 Non-Incendive Class I, Div. 2,Groups A, B, C, & D Class II, Div. 2, Groups E, F, & G Class III, Type 4X, IP 66, T4 Class I, Div. 1,Groups A, B, C, & D Class II, Div. 1, Groups E, F, & G Class III, Type 4X, IP 66, T4 Ex II 1/2 G, EEx d IIC T6 Intrinsically Safe ATEX 96X-XXAX-XC0 96X-XXAX-XC1 96X-XXAX-XC2 96X-XXAX-XC3 with transducers 9XX-AXXX-XXX 9XX-SXXX-XXX 9XX-BXXX-XXX 9XX-CXXX-XXX 9XX-NXXX-XXX 9XX-KXXX-XXX 96X-50AX-XA0 96X-50AX-XA1 96X-50AX-XA2 96X-50AX-XA3 with transducers 9XX-AXXA-XXX 9XX-SXXA-XXX 9XX-BXXA-XXX 9XX-CXXA-XXX 9XX-NXXA-XXX 9XX-KXXA-XXX Flameproof Intrinsically Safe Ex II 1 G, EEx ia IIC T5 0344 These units are in compliance with: 1. The EMC Directive: 89/336/EEC. The units have been tested to EN 61326. 2. Directive 94/9/EC for equipment or protective system for use in potentially explosive atmospheres. 11 QUALITY The quality assurance system in place at Magnetrol® guarantees the highest level of quality throughout the company. MAGNETROL is committed to providing full customer satisfaction both in quality products and quality service. The MAGNETROL quality assurance system is registered to ISO 9001 affirming its commitment to known international quality standards providing the strongest assurance of product and service quality available. ESP Several ECHOTEL Model 961 units are available for quick shipment, usually within one week after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP). To take advantage of ESP, simply match the color coded model number codes (standard dimensions apply). ESP service may not apply to orders of ten units or more. Contact your local representative for lead times on larger volume orders, as well as other products and options. Expedite Ship Plan WARRANTY All MAGNETROL electronic level and flow controls are warranted free of defects in materials or workmanship for one full year from the date of original factory shipment. If returned within the warranty period; and, upon factory inspection of the control, the cause of the claim is determined to be covered under the warranty; then, MAGNETROL will repair or replace the control at no cost to the purchaser (or owner) other than transportation. MAGNETROL shall not be liable for misapplication, labor claims, direct or consequential damage or expense arising from the installation or use of equipment. There are no other warranties expressed or implied, except special written warranties covering some MAGNETROL products. For additional information, see Instruction Manual 51-646. 5300 Belmont Road • Downers Grove, Illinois 60515-4499 • 630-969-4000 • Fax 630-969-9489 • www.magnetrol.com 145 Jardin Drive, Units 1 & 2 • Concord, Ontario Canada L4K 1X7 • 905-738-9600 • Fax 905-738-1306 Heikensstraat 6 • B 9240 Zele, Belgium • 052 45.11.11 • Fax 052 45.09.93 Regent Business Ctr., Jubilee Rd. • Burgess Hill, Sussex RH15 9TL U.K. • 01444-871313 • Fax 01444-871317 Copyright © 2011 MAGNETROL INTERNATIONAL, INCORPORATED. All rights reserved. Printed in the USA. Performance specifications are effective with date oftrademarks of MAGNETROL INTERNATIONAL, INCORPORATED. MAGNETROL, MAGNETROL logotype and ECHOTEL are registered issue and are subject to change without notice. Kynar® is a registered trademark of Elf Atochem North America, Inc. Hastelloy® is a registered trademark of HAYNES INTERNATIONAL, INC. (DELAWARE CORPORATION). Monel® is a registered trademark of the INCO family of companies. Tri-Clamp® is a registered trademark of Ladish Co. Varivent® is a registered trademark of Tuchenhagen GmbH LTD BULLETIN: 51-137.3 EFFECTIVE: August 2011 SUPERSEDES: November 2009