1612S48XA

www.make-ps.com E-mail:info@make-ps.com 1600XA series FEATURES • • • • • • • Single, Dual, Triple Output DC/DC Converter 6 sided Continuous Shielding Synchronization 10W/In3 Power Density Wide 2:1 Input Voltage Range Efficiency to 82% -55oC to +85oC Operation Meets MIL-STD-810 & MIL-STD-202 DESCRIPTIONS The 1600XA series 16 watts high performance DC/DC converters are cost effective solution to the high reliability and performance requirements of power distribution systems in applications ranging from high speed data communications equipment to industrial robotic systems. The 1600XA series operates from wide (2:1) input voltage ranges of 9 to 18, 18 to 36 or 36 to 72VDC; providing single, dual and triple output combinations of 5, 12, 15, ±5, ±12, ±15, 5/±12 and 5/±15 VDC. All models are packaged in compact, low profile 2” X 2” X 0.4” metal cases. INPUT CHARACTERISTICS Min Typ Max Unit/Comments Input Voltage Range 12 VDC Input Models VDC 12 18 9 24 VDC Input Models VDC 18 24 36 48 VDC Input Models VDC 36 48 72 Remote On / OFF Control Supply ON VDC or Open Circuit 3.5 Supply OFF 0 0.8 VDC Logic Referenced to Negative Input Input Filter Pi Filter OUTPUT CHARACTERISTICS Min Typ Max Unit/Comments Output Voltage Accuracy Single & Dual Outputs Triple Outputs - Primary - Auxiliaries Output Voltage Trim Voltage Balance: Dual Outputs Triple Outputs (Auxiliaries) Minimum Load Line Regulation Single & Dual Outputs Triple Outputs - Primary - Auxiliaries Load Regulation Single Outputs Dual Outputs Triple Outputs - Primary - Auxiliaries Ripple/Noise Short Circuit Protection Transient Recovery Time Temperature Coefficient Over Voltage Protection 1 2 3 GENERAL CHARACTERISTICS Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Acceleration Shock Vibration Altitude Switching Frequency Unit/Comments See Model Selection Guide 1400 VDC Min., 1 minute Meets requirements of MIL-STD-202F, method 301 >109 Ohms; Meets requirements of MIL-STD-202F, method 302, test condition B 140 pF Per MIL-STD-810E, method 513.4, procedure II. Operational test (centrifuge) 12g’s (manned aerospace vehicles) Per MIL-STD-801E, method 516.4, procedure I. Functional shock 40g’s. Per MIL-STD-810E, method 514.4, procedure I, category 6 (equipment installed in helicopters). Per MIL-STD-810E, method 500.3, procedure III Rapid decompression, 40K ft. 100 kHz, Min. ±1.0 ±1.0 ±6.0 ±5 %1 %1 %1 % ±1.0 %; Equal Output Loads ±1.0 %; Equal Output Loads 10% Full Load ±0.5 % 2 ±0.2 % 2 ±6.0 % 2 %3 % 3 ; Equal Loads %3 % 3 ; Equal Loads % of Vout Continuous, Automatic Recovery 200 μS to within1% error band for 50% step load change ±0.01 % per oC See Model Selection Guide ±0.2 ±1.0 ±0.5 ±6.0 2 = Output voltage at nominal line & FL = % Output voltage measured from min. input line to maximum = Output voltage measured from FL to 10% Load >> 1 www.make-ps.com ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range (Industrial) Max. Case Temp. Storage Temp. Range Relative Humidity Cooling EMI/RFI Min -55 Typ Max Unit/Comments +85 oC; Ambient E-mail:info@make-ps.com PHYSICAL CHARACTERISTICS Case Size Unit/Comments 2.0 X 2.0 X 0.4 inches (51.0 X 51.0 X 10.2 mm) Coated Copper 2.8 oz (79 grams) 6-sided, Continuous +100 oC; Ambient -55 +125 oC; Ambient Per MIL-STD-801E, method 507.3, procedure I. Natural non-hazardous items, cycle 1,240 Hrs Free-Air Convection Six-sided Metal Case Case Material Weight Shielding Shielding Connection Negative Input, Pin 3 12V and 24V Input Models Positive Input, Pin 4 48V Input Models Reliability Specs: MTBF, Ground >705,000 Hrs Benign, @+25oC OUTLINE DRAWING CASE A 2.00 (50.8) 0.40 (10.2) 0.40 (10.2) 0.40 0.40 (10.2) (10.2) 0.10 (2.5) 0.040±.005 (1.01) DIA. PIN OUT CHART; CASE A Pin 1 2 3 4 5 6 7 8 Single Dual Triple Remote On/Off Remote On/Off Remote On/Off Sync Sync Sync - Vin - Vin - Vin + Vin + Vin + Vin Trim Trim - Vout (Aux) - Vout - Vout Common + Vout Common -5V Vout No Pin + Vout +Vout (Aux) 8 7 6 5 BOTTOM 2.00 (50.8) SIDE 4 3 2 1 0.10 (2.5) 0.15MIN. (3.8) 0.90 (22.9) .20 .20 .20 (5.1) (5.1) (5.1) 0.40 (10.2) CASE A1 2.00 (50.8) 0.40 (10.2) 0.40 (10.2) 0.60 (15.2) 0.040±.005 (1.01) DIA. 2.00 0.80 (50.8) (20.3) Ordering Information: 1. Case “A” pinning is standard. Models with Case “A” packaging do not require a suffix on the part number. 2. Case “A1” is an alternate. Models with Case “A1” packaging must be designated with an “A1” suffix; e.g. 1615D48XA-A1. PIN OUT CHART; CASE A1 Pins 1 2 3 4 5 SIDE Single + Vin - Vin + Vout Trim - Vout Dual + Vin - Vin + Vout +/- Common - Vout 3 4 5 BOTTOM 1 2 0.60 (15.2) 0.90 (22.9) 0.15MIN. (3.8) 0.20 (5.1) 0.40 (10.2) Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. >> 2 www.make-ps.com HOW TO ORDER E-mail:info@make-ps.com HOW TO ORDER 16 XX D XX XA - A1 Wattage Output Voltage Output Configuration (S=Single, D=Dual) Nom.Input Voltage OPTION -A1= Optional PinConfig. Model Series 1605/12 T XX XA - A1 Wattage Output Voltage Aux.Output Voltage Output Configuration (Triple) Nom.Input Voltage OPTION -A1= Optional PinConfig. Model Series MODEL SELECTION CHART Model Nominal Input Voltage (VDC) 12 12 12 12 12 12 24 24 24 24 24 24 48 48 48 48 48 48 12 12 24 24 48 48 Input Voltage Range (VDC) 9 - 18 9 - 18 9 - 18 9 - 18 9 - 18 9 - 18 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 9 - 18 9 - 18 18 - 36 18 - 36 36 - 72 36 - 72 No Load Input Current (mA) 45 45 45 45 45 45 34 34 34 34 34 34 32 32 32 32 32 32 50 50 45 45 35 35 Full Load Input Current (mA) 1667 1640 1650 1667 1640 1650 833 810 815 833 810 815 411 405 408 411 405 408 1667 1667 832 832 406 401 Output Voltage (VDC) 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 5/±12 5/±15 5/±12 5/±15 5/±12 5/±15 Output Current (mA) 3200 1300 1060 ±1600 ±665 ±535 3200 1300 1060 ±1600 ±665 ±535 3200 1300 1060 ±1600 ±665 ±535 2000/±250 2000/±200 2000/±250 2000/±200 2000/±250 2000/±200 Over Voltage (VDC) 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8, ±15.0 6.8, ±18.0 6.8, ±15.0 6.8, ±18.0 6.8, ±15.0 6.8, ±18.0 Efficiency (%) Case 1605S12XA 1612S12XA 1615S12XA 1605D12XA 1612D12XA 1615D12XA 1605S24XA 1612S24XA 1615S24XA 1605D24XA 1612D24XA 1615D24XA 1605S48XA 1612S48XA 1615S48XA 1605D48XA 1612D48XA 1615D48XA 1605/12T12XA 1605/15T12XA 1605/12T24XA 1605/15T24XA 1605/12T48XA 1605/15T48XA 80 81 81 80 81 81 80 82 82 80 82 82 81 82 82 81 82 82 75 79 81 75 79 81 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 A, A1 >> 3