215D12VFI

www.make-ps.com E-mail:info@make-ps.com 200VFI series FEATURES • • • • • • Single & Dual Output DC/DC Converter Single and Dual Output, 2 watt converter 4000 VAC Input/Output Isolation Available in 5, 12, and 24 VDC Inputs Wide Operating Temperature Range MTBF > 600,000 Hours Low Cost DESCRIPTIONS The 200VFI series is a family of cost effective 2 watt single and dual output DC/DC converters. 18 models operate from input bus voltages of 5V, 12V and 24V; producing output voltage levels of 5V, 12V, 15V, ±5V, ±12V and ±15V for a wide range of choices. The 200VFI series is ideal for a variety of applications including distributed power systems, mixed analog / digital subsystems, portable test equipment, local power networks and battery backed systems. INPUT CHARACTERISTICS Min Typ Input Voltage 5 VDC Input Models 4.5 5 12 VDC Input Models 10.8 12 24 VDC Input Models 13.5 24 Input Fuse Requirements 5 VDC Input Models 1000 12 VDC Input Models 500 24 VDC Input Models 250 Input Filter Max Unit/Comments 5.5 13.2 26.4 VDC VDC VDC mA; Slow blow type mA; Slow blow type mA; Slow blow type Pi Filter OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Balance (Duals) Line Regulation Min Typ Max Unit/Comments ±2.0 ±4.0 % Output voltage at nominal line & FL ±2.0 ±4.0 % Equal Output Loads ±0.3 ±0.5 %; % Change / Percentage change in Input voltage ±0.5 ±1.0 % Output voltage measured from FL to 10% load 30 50 mV p-p, Nom.Line @FL, 20MHz B.W., using 1 μf bypass capacitor 100 mV p-p, Over Line, Load & Temp., 20 MHz B.W., using 1 μf bypass capacitor %Rated Output Load 120 Continuous ±0.01 ±0.02 % per degree C GENERAL CHARACTERISTICS Switching Frequency Isolation Voltage Isolation Resistance Isolation Capacitance MTBF (MIL-HBK-217F) Min Typ Max Unit/Comments kHz 25 50 80 VDC, 60 sec. 6,000 Mohm, 500VDC 10,000 20 30 pF, 100kHz, 1Volt Million Hours, 0.6 +25oC, Ground Benign Load Regulation Ripple/Noise Ripple/Noise Overload Protection Short Circuit Protection Temperature Coefficient >> B-33 www.make-ps.com ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Operating Temp. Range Storage Temp. Range Relative Humidity Cooling Min -25 -25 -40 Typ Max +60 +90 +125 +95 Unit/Comments o C; Ambient o C; Case o C % Humidity; noncondensing Free-Air Convection E-mail:info@make-ps.com PHYSICAL CHARACTERISTICS Case Size Case Material Flammability Weight Unit/Comments 1.25 X 0.80 X 0.40 inches (31.8 X 20.3 X 10.2 mm) Non-Conductive Black Plastic UL94V-0 12.4 Grams OUTLINE DRAWING 1.25 (31.8) 0.15 (3.8) SIDE VIEW 0.40 (10.2) 0.020(0.50) PIN DIA. 0.10 (2.5) 0.100 (2.54) 0.08 (2.0) 12 10 11 12 BOTTOM VIEW 24 23 15 13 0.600 0.80 (15.22) (20.3) PIN OUT CHART Pins 1 2 10 11 12 13 15 23 24 Single + Vin + Vin No Pin No Pin - Vout + Vout No Pin - Vin - Vin Dual + Vin + Vin Common Common No Pin - Vout + Vin - Vin - Vin Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 Pin : ±0.002 ±0.05 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across input is recommended for operation. >> B-34 www.make-ps.com HOW TO ORDER E-mail:info@make-ps.com HOW TO ORDER 2 XX S XX VFI - Y Wattage=2 W Output Voltage Output Configuration (S=Single, D=Dual) ROHS Compliant Series Nominal Input Voltage MODEL SELECTION CHART Model 205S5VFI 212S5VFI 215S5VFI 205S12VFI 212S12VFI 215S12VFI 205S24VFI 212S24VFI 215S24VFI 205D5VFI 212D5VFI 215D5VFI 205D12VFI 212D12VFI 215D12VFI 205D24VFI 212D24VFI 215D24VFI Nominal Input Voltage (VDC) 5 5 5 12 12 12 24 24 24 5 5 5 12 12 12 24 24 24 Output Voltage (VDC) 5 12 15 5 12 15 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 Full Load Output Current (mA) 400 165 133 400 165 133 400 165 133 ±100 ±83 ±66 ±100 ±83 ±66 ±100 ±83 ±66 No Load Input Current (mA) 100 100 100 50 50 50 30 30 30 100 100 100 50 50 50 30 30 30 Full Load Input Current (mA) 645 629 623 269 262 260 134 131 130 476 699 695 185 281 280 93 143 142 Reflected Ripple Current (mA) 62 63 64 62 63 64 62 63 64 42 57 57 45 59 59 45 58 58 >> B-35 www.make-ps.com DERATING CURVES E-mail:info@make-ps.com MODEL 200VFI Pout % 100 90 80 70 60 50 40 30 20 10 0 -25 100LFM 200LFM Natural Convection 400LFM ~ 50 60 70 80 90 100 110 TEMPERATURE ° C >> B-36