MTG7-001I-XBD00-GR-0B01

Cree XB-D Color Series on Board Cree XB-D Color Series Cree XLamp XB-D color LEDs extend the double lumens-per-dollar performance of the XB package to color LEDs, delivering up to 40% higher maximum light output than XP-E color LEDs. The combination of performance and small size of XB-D color LEDs enable better color mixing and lower system cost. FEATURES > Cree's smallest lighting class LED: 2.45 x 2.45 mm > 1A Maximum Drive Current > Wide viewing angle: 115°(white) to 140° (red) > Electrically Neutral Thermal Path FLUX CHARACTERISTICS @ 85°C COLOR Blue Green Red-Orange Red CHARACTERISTICS Thermal resistance, junction to solder point - white, royal blue, blue Thermal resistance, junction to solder point - green Thermal resistance, junction to solder point - amber Thermal resistance, junction to solder point - red-orange, red Viewing angle (FWHM) - white Viewing angle (FWHM) - royal blue, blue, green Viewing angle (FWHM) - amber, red-orange, red Temperature coefficient of voltage - white Temperature coefficient of voltage - royal blue, blue, green Temperature coefficient of voltage - amber, red-orange, red ESD classification (HBM per Mil-Std-883D) DC forward current Reverse voltage Forward voltage (@ 350 mA, 85 °C) - white Forward voltage (@ 350 mA, 25 °C) - royal blue, blue Forward voltage (@ 350 mA, 25 °C) - green Forward voltage (@ 350 mA, 25 °C) - amber, red-orange, red LED junction temperature APPLICATIONS > Non-Directional > Directional > Downlight > Consumer Portable DWL (nm) MIN.FLUX (LM) @350MA KIT USED 35.2 465-485 0Z01 93.9 520-535 0B01 O901 80.6 610-620 O701 620-630 67.2 UNIT °C/W °C/W °C/W °C/W degrees degrees degrees mV/°C mV/°C mV/°C mA V V V V V °C MINIMUM TYPICAL 6.5 11 7 5 115 135 140 -2.5 -3.3 -2 Class 2 2.9 3.1 3.3 2.25 MAXIMUM 1000 -5 3.5 3.7 3.9 2.6 150 It is highly recommended for the user to review the CREE XBD Series page for additional and most recent technical data at: http://www.cree.com/led-components-and-modules/products/xlamp/discrete-directional/xlamp-xbd Global Headquarters, 3 Northway Lane North, Latham, NY 12110, USA www.marktechopto.com TOLL FREE: 1-800-984-5337 • PHONE: 518-956-2980 • FAX: 518-785-4725 • EMAIL: info@marktechopto.com Cree XB-D Color Series on Board * Exceeding maximum ratings may damage the LED and cause potential safety hazards. * Elevated operating temperatures can be expected to negatively impact the service life (lumen output) * All data is related to entire assembly. Data reflects statistical mean values. Actual data may differ depending on variances in the manufacturing process. * End users need to take into account the lumen depreciation as the temperature rises with various thermal solutions installed. Note 1: Using continuously under elevated loads (i.e. the application of high temperature/current/voltage or a significant change in temperature, etc.) may cause this product to significantly decrease in reliability even if the operating conditions are within the absolute maximum ratings. Note 2: The thermal resistance from the LED junction to ambient temperature, Rth(j-a), should be kept below 10°C/W so that the LED is not exposed to a condition beyond the absolute maximum ratings. Note 3: The temperature of the LED assembly must be measured at the TC-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. Hardware (not included) > Mount with #4 Machine Screws. > 16AWG Maximum Wire Gauge. > Use only with constant current power supplies. PCB Fabrication > Layer Count: 1 > Core Material: 6061-T6 Aluminum > Single Layer Copper Weight: 1oz > Solder Mask: White > Finishing Plating: Pb Free HASL Global Headquarters, 3 Northway Lane North, Latham, NY 12110, USA www.marktechopto.com TOLL FREE: 1-800-984-5337 • PHONE: 518-956-2980 • FAX: 518-785-4725 • EMAIL: info@marktechopto.com