88E1145

Transceiver Solutions Alaska® Quad Gigabit Ethernet Transceiver 88E1141/88E1145 PRODUCT OVERVIEW The Marvell¨ Alaska¨ family of Gigabit Ethernet (GbE) over copper transceivers are the industryÕs lowest power, smallest form factor, highest performance, and highest port density solutions in volume production. The Alaska Quad 88E1141 and 88E1145 transceivers lead the industry with the lowest power consumption (under 3W for the entire device), enabling network systems manufacturers to decrease system cost by reducing both power supply and fan requirements. Additionally, the 88E1145 device offers the smallest package footprint (21 mm x 21 mm) and requires 40% less board space than competing Gigabit solutions. The Alaska Quad products offer additional support of 1000BASE-X through an integrated 1.25 GHz Serializer/Deserializer (SERDES). D/A Waveshape Filter Echo Canceller Near End Crosstalk Canceller Feed Forward Equalizer Trellis Decoder Decision Feedback Equalizer 10/100/1000 Transmit PCS P0_TX_CTL P0_TXD[3:0] P0_GTX_CLK Timing Control Active Hybrid Gain Control Baseline 10BASE-T Receiver P0_MDC P0_MDIO P0_INTn P0_RSET P0_HSDACP/N P0_TSTPT Fiber/SERDES Transmit P0_S_IN+/P0_S_CLK+/P0_S_OUT+/- A/D DPLL Skew Control 10/100/1000 Receive PCS P0_RX_CTL P0_RXD[3:0] P0_RX_CLK Management Interface Bias/Test Registers LED/ ConÞguration Auto-Negotiation P0_LED_LINK10 P0_LED_LINK100 P0_LED_LINK1000 P0_LED_DUPLEX P0_LED_RX P0_LED_TX GCONFIG[1:0] JTAG TRST# TCK TDI TMS TDO Clock/Reset XTAL1 XTAL2 RESETn 125CLK Fig 1. Alaska Quad GbE Transceiver (88E1141/88E1145) Block Diagram FEATURES ¥ Highly integrated 4-port device ¥ Ultra low power, only 0.75W/port ¥ 10/100/1000BASE-T IEEE 802.3 compliant ¥ Supports GMII/RGMII/SGMII/TBI/RTBI interfaces ¥ Virtual Cable Testerª (VCT) feature ¥ Integrated 1.25 GHz SERDES ¥ Media Detect feature automatically detects and conÞgures to either copper or Þber media ¥ Automatic support for 2-pair CAT 5 cable (100 Mbps) ¥ Power management modes ¥ Four RGMII timing modes ¥ Operation up to 180 meters CAT 5 cable ¥ Auto-MDI/MDIX crossover for all modes of operation ¥ Support IEEE 1149.1 (JTAG) and NAND-tree ICT ¥ Advanced mixed-signal and DSP techniques BENEFITS ¥ Enables highly integrated Gigabit switches ¥ Enables higher integration and reduced system cost ¥ Compatibility with existing installed base of compliant devices ¥ Reduces cost and simpliÞes PCB layout ¥ IdentiÞcation and isolation of cable faults ¥ Supports 1000BASE-X Þber applications ¥ Complete media ßexibility ¥ Operates over installed 2-pair cable ¥ Reduced system power ¥ Eliminate the need for on-board delay lines ¥ Functions over a wider base of cabling infrastructures ¥ Eases installation and reduces cost ¥ SimpliÞes board level testing/debugging ¥ Advanced DSP design Alaska® Quad Gigabit Ethernet Transceiver FEATURES ¥ IEEE 802.3u compliant Auto-Negotiation ¥ Active internal hybrids for 1000BASE-T ¥ Direct drive LED support ¥ Software conÞgurable LED support ¥ User programmable PHY address ¥ Loopback mode BENEFITS ¥ Automatically conÞgures to 10, 100 or 1000 Mbps ¥ Lower cost magnetics ¥ Eliminates cost of external LED latches and drivers ¥ User-deÞned LED conÞguration ¥ Works with all existing Gigabit switch designs ¥ Assists testing and diagnostics APPLICATIONS The Marvell Alaska Quad transceivers enable higher port count Gigabit switches, up to 48 ports. Through integrated SERDES technology, the device also offers optional support for 1000BASE-SX/LX Gigabit Þber standards, on a per port basis, enabling mixed-media Gigabit switches. The Alaska Quad products support the GMII, RGMII, SGMII, TBI, and RTBI PHY/MAC interface options. The Alaska Quad transceivers offer the most advanced feature set including VCT technology used to diagnose the attached cable plant and isolate and report cable faults with one-meter accuracy. Additionally, the devices feature Ò2-pair downshiftÓ capability for plug-and-play operation in 2-pair cable environments, as well the Media Detect feature which supports both copper and Þber media simultaneously. 10/100/1000 Mbps Ethernet MAC Port 0 10/100/1000 Mbps Ethernet MAC Port 1 10/100/1000 Mbps Ethernet MAC Port 3 MAC Interface Options: ¥ GMII ¥ RGMII ¥ SGMII ¥ TBI ¥ RTBI ¥ Serial Interface (SERDES) RJ45 Port 0 Alaska Quad PHY RJ45 Port 1 Ethernet Gigabit MAC Port 0 Ethernet Gigabit MAC Port 1 Alaska Quad PHY Fiber Optics Port 0 Fiber Optics Port 1 Magnetics RJ45 Port 3 Media Types: ¥ 10BASE-T ¥ 100BASE-TX ¥ 1000BASE-T Ethernet Gigabit MAC Port 3 MAC Interface Options: ¥ GMII ¥ RGMII ¥ TBI ¥ RTBI Fiber Optics Port 3 Serial Interface (SERDES) Media Types: ¥ 1000BASE-SX ¥ 1000BASE-LX Fig 2. Alaska Quad GbE Transceiver (88E1141/88E1145) Copper Applications Diagram Fig 3. Alaska Quad GbE Transceiver (88E1141/88E1145) Fiber Applications Diagram THE MARVELL ADVANTAGE: The Marvell Alaska Quad GbE transceivers come with a complete set of hardware and software development tools to assist network hardware engineers with product evaluation. MarvellÕs worldwide Þeld applications engineers collaborate closely with network equipment vendors to develop and deliver new competitive products to market on time. Marvell utilizes recognized world-leading semiconductor foundry and packaging services to reliably deliver high-volume and low cost total solutions. For more information, visit our website at www.marvell.com. Marvell Semiconductor, Inc. 700 First Avenue Sunnyvale, CA 94089 Phone 408.222.2500 www.marvell.com ©2002 Marvell International Ltd. All rights reserved. Marvell, the Marvell logo, Moving Forward Faster, Alaska, the Galileo logo, and GalNet are registered trademarks of Marvell. Discovery, Fastwriter, Galileo Technology, GalTis, Horizon, Libertas, Link Street, PHY Advantage, Prestera, Raise the Technology Bar, Virtual Cable Testers, and Yukon are trademarks of Marvell. All other trademarks are the property of their respective owners. 88E1141/1145-001 11/02