MAX9725_07

19-3465; Rev 2; 11/07 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown General Description The MAX9725A–MAX9725D fixed-gain, stereo headphone amplifiers are ideal for portable equipment where board space is at a premium. The MAX9725E offers the flexibility to adjust the gain with external input and feedback resistors. The MAX9725A–MAX9725E use a unique, patented DirectDriveTM architecture to produce a groundreferenced output from a single supply, eliminating the need for large DC-blocking capacitors, saving cost, board space, and component height. Fixed gains of -2V/V (MAX9725A), -1.5V/V (MAX9725B), -1V/V (MAX9725C), and -4V/V (MAX9725D) further reduce external component count. The adjustable gain of the MAX9725E DirectDrive headphone amplifier allows for any gain down to -1V/V using external resistors. The MAX9725 delivers up to 20mW per channel into a 32Ω load and achieves 0.006% THD+N. An 80dB at 1kHz power-supply rejection ratio (PSRR) allows the MAX9725 to operate from noisy digital supplies without an additional linear regulator. The MAX9725 includes ±8kV ESD protection on the headphone output. Comprehensive click-andpop circuitry suppresses audible clicks and pops at startup and shutdown. A low-power shutdown mode reduces supply current to 0.6µA (typ). The MAX9725 operates from a single 0.9V to 1.8V supply, allowing the device to be powered directly from a single AA or AAA battery. The MAX9725 consumes only 2.1mA of supply current, provides short-circuit protection, and is specified over the extended -40°C to +85°C temperature range. The MAX9725 is available in a tiny (1.54mm x 2.02mm x 0.6mm) 12-bump chip-scale package (UCSP™) and a 12-pin thin QFN package (4mm x 4mm x 0.8mm). Features ♦ Low Quiescent Current: 2.1mA (MAX9725A–MAX9725D) 2.3mA (MAX9725E) ♦ Single-Cell, 0.9V to 1.8V Single-Supply Operation ♦ Fixed Gain Eliminates External Feedback Network MAX9725A: -2V/V MAX9725B: -1.5V/V MAX9725C: -1V/V MAX9725D: -4V/V ♦ Adjustable Gain with External Input and Feedback Resistors MAX9725E: Minimum Stable Gain of -1V/V ♦ Ground-Referenced Outputs Eliminate DC Bias ♦ No Degradation of Low-Frequency Response Due to Output Capacitors ♦ 20mW per Channel into 32Ω ♦ Low 0.006% THD+N ♦ High PSRR (80dB at 1kHz) ♦ Integrated Click-and-Pop Suppression ♦ Low-Power Shutdown Control ♦ Short-Circuit Protection ♦ ±8kV ESD-Protected Amplifier Outputs ♦ Available in Space-Saving Packages 12-Bump UCSP (1.54mm x 2.02mm x 0.6mm) 12-Pin Thin QFN (4mm x 4mm x 0.8mm) MAX9725 Block Diagrams VDD C3 SINGLE 1.5V CELL AA OR AAA BATTERY MAX9725A–MAX9725D INL OUTL DirectDrive OUTPUTS ELIMINATE DC-BLOCKING CAPACITORS. Applications MP3 Players Cellular Phones PDAs Smart Phones Portable Audio Equipment C1P Ordering Information PART MAX9725AEBC+T MAX9725AETC+ MAX9725BEBC+T PINPACKAGE 12 UCSP-12 12 TQFN-EP* 12 UCSP-12 PKG CODE B12-1 T1244-4 B12-1 TOP MARK +ACK +AAEW +ACL GAIN (V/V) -2 -2 -1.5 C1N INVERTING CHARGE PUMP PVSS C2 VSS INR OUTR Ordering Information continued at end of data sheet. Note: All devices are specified over the -40°C to +85°C operating temperature range. +Denotes a lead-free package. T = Tape and reel. *EP = Exposed pad. UCSP is a trademark of Maxim Integrated Products, Inc. SGND PGND Block Diagrams continued at end of data sheet. Pin Configurations appear at end of data sheet. 1 ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 ABSOLUTE MAXIMUM RATINGS SGND to PGND .....................................................-0.3V to +0.3V VDD to SGND or PGND ............................................-0.3V to +2V VSS to PVSS ...........................................................-0.3V to +0.3V C1P to PGND..............................................-0.3V to (VDD + 0.3V) C1N to PGND............................................(PVSS - 0.3V) to +0.3V VSS, PVSS to GND ....................................................+0.3V to -2V OUTR, OUTL, INR, INL to SGND (MAX9725A–MAX9725D)..............(VSS - 0.3V) to (VDD + 0.3V) OUTR, OUTL to SGND (MAX9725E) ..................................(VSS - 0.3V) to (VDD + 0.3V) INR, INL to SGND (MAX9725E)...................................-4V to +4V SHDN to SGND or PGND .........................................-0.3V to +4V Output Short-Circuit Current ......................................Continuous Continuous Power Dissipation (TA = +70°C) 12-Bump UCSP (derate 6.5mW/°C above +70°C)....518.8mW 12-Pin Thin QFN (derate 16.9mW/°C above +70°C) ..1349.1mW Junction Temperature ......................................................+150°C Operating Temperature Range ...........................-40°C to +85°C Storage Temperature Range .............................-65°C to +150°C Bump Temperature (soldering) Reflow............................+230°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (MAX9725A–MAX9725D) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, RL = ∞, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (See the Functional Diagrams.) (Note 1) PARAMETER Supply Voltage Range Quiescent Supply Current Shutdown Current Shutdown to Full Operation SHDN Thresholds SHDN Input Leakage Current CHARGE PUMP Oscillator Frequency AMPLIFIERS MAX9725A Voltage Gain AV MAX9725B MAX9725C MAX9725D Gain Match Total Output Offset Voltage Input Resistance Power-Supply Rejection Ratio ∆AV VOS RIN PSRR VDD = 0.9V to 1.8V, TA = +25°C fIN = 1kHz 100mVP-P ripple fIN = 20kHz VDD = 1.5V Output Power (Note 3) POUT VDD = 1.0V, RL = 32Ω VDD = 0.9V, RL = 32Ω RL = 32Ω RL = 16Ω Input AC-coupled, RL = 32Ω to GND, TA = +25°C MAX9725A/MAX9725D MAX9725B MAX9725C 15 60 -2.04 -1.53 -1.02 -4.08 -2.00 -1.5 -1.00 -4.00 ±0.5 ±0.3 ±0.45 ±0.6 25 80 70 62 10 20 25 7 6 mW ±1.05 ±1.58 ±2.1 35 kΩ dB -1.96 -1.47 -0.98 -3.92 % mV V/V SYMBOL VDD IDD ISHDN tON VIH VIL ILEAK fOSC CONDITIONS Guaranteed by PSRR test Both channels active VSHDN = 0V TA = +25°C TA = -40°C to +85°C 180 VDD = 0.9V to 1.8V VDD = 0.9V to 1.8V VDD = 0.9V to 1.8V (Note 2) 493 580 0.7 x VDD 0.3 x VDD ±1 667 MIN 0.9 2.1 0.6 TYP MAX 1.8 3.3 10 30 UNITS V mA µA µs V µA kHz 2 _______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown ELECTRICAL CHARACTERISTICS (MAX9725A–MAX9725D) (continued) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, RL = ∞, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (See the Functional Diagrams.) (Note 1) PARAMETER Total Harmonic Distortion Plus Noise Signal-to-Noise Ratio Slew Rate Maximum Capacitive Load Crosstalk Click-and-Pop Level ESD Protection SYMBOL THD+N SNR SR CL XTALK KCP VESD No sustained oscillations fIN = 1.0kHz, RL = 32Ω, POUT = 5mW RL = 32Ω, peak voltage, A-weighted, 32 samples per second (Note 4) Into shutdown Out of shutdown CONDITIONS RL = 32Ω, POUT = 12mW, f = 1kHz RL = 16Ω, POUT = 15mW, f = 1kHz BW = 22Hz to 22kHz RL = 32Ω, POUT = 12mW A-weighted filter MIN TYP 0.006 0.015 89 92 0.2 150 100 72.8 dBV 72.8 ±8 kV MAX UNITS % dB V/µs pF dB MAX9725 Human Body Model (OUTR, OUTL) ELECTRICAL CHARACTERISTICS (MAX9725E) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, RL = 32Ω, RF = 60kΩ, RIN = 10kΩ, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (See the Functional Diagrams.) (Note 1) PARAMETER Supply Voltage Range Quiescent Supply Current Shutdown Current Shutdown to Full Operation SHDN Thresholds SHDN Input Leakage Current CHARGE PUMP Oscillator Frequency AMPLIFIERS Voltage Gain Minimum Stable Gain Total Output Offset Voltage Input Resistance INR, INL Input Leakage Current Maximum Input Parasitic Capacitance Power-Supply Rejection Ratio AV ∆AV VOS RIN ILK CPAR VDD = 0.9V to 1.8V, TA = +25°C PSRR 100mVP-P ripple (Note 5) fIN = 1kHz fIN = 20kHz 52.9 5 67.8 70 62 dB Input AC-coupled, RL = 32Ω to GND, TA = +25°C (Note 6) 6.3 (Note 5) -6.11 -6.07 -1.0 ±0.63 9.78 ±2.1 14 ±100 -6.00 V/V V/V mV kΩ nA pF SYMBOL VDD IDD ISHDN tON VIH VIL ILEAK fOSC CONDITIONS Guaranteed by PSRR test Both channels active VSHDN = 0V TA = +25°C TA = -40°C to +85°C 180 VDD = 0.9V to 1.8V VDD = 0.9V to 1.8V VDD = 0.9V to 1.8V (Note 2) 483 592 0.7 x VDD 0.3 x VDD ±1 687 MIN 0.9 2.3 0.6 TYP MAX 1.8 3.7 1 10 UNITS V mA µA µs V µA kHz _______________________________________________________________________________________ 3 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 ELECTRICAL CHARACTERISTICS (MAX9725E) (continued) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, RL = 32Ω, RF = 60kΩ, RIN = 10kΩ, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (See the Functional Diagrams.) (Note 1) PARAMETER SYMBOL VDD = 1.5V Output Power (Note 3) POUT VDD = 1.0V, RL = 32Ω VDD = 0.9V, RL = 32Ω Total Harmonic Distortion Plus Noise (Note 5) Signal-to-Noise Ratio Slew Rate Maximum Capacitive Load Crosstalk Click-and-Pop Level ESD Protection Attenuation in Shutdown THD+N SNR SR CL XTALK KCP VESD ATT(SD) No sustained oscillations fIN = 1.0kHz, RL = 32Ω, POUT = 5mW RL = 32Ω, peak voltage, A-weighted, 32 samples per second (Note 4) Into shutdown Out of shutdown RL = 32Ω, POUT = 12mW, f = 1kHz RL = 16Ω, POUT = 15mW, f = 1kHz BW = 22Hz to 22kHz RL = 32Ω, POUT = 12mW A-weighted filter CONDITIONS RL = 32Ω RL = 16Ω MIN 10 TYP 24 25 7 6 0.006 0.015 89 92 0.3 150 100 72.8 dBV 72.8 ±8 -120 -75 kV dB % dB V/µs pF dB mW MAX UNITS Human Body Model (OUTR, OUTL) VSHDN = 0V RL = 32Ω RL = 10kΩ Note 1: Note 2: Note 3: Note 4: All specifications are 100% tested at TA = +25°C; temperature limits are guaranteed by design. Input leakage current measurements limited by automated test equipment. fIN = 1kHz, TA = +25°C, THD+N < 1%, both channels driven in-phase. Testing performed with 32Ω resistive load connected to outputs. Mode transitions controlled by SHDN. KCP level calculated as 20 log [peak voltage under normal operation at rated power level / peak voltage during mode transition]. Inputs are ACgrounded. Note 5: Using existing resistors with 1% precision. Note 6: RIN = 10Ω, RF =10kΩ. Typical Operating Characteristics (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise noted.) (See the Functional Diagrams.) TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY MAX9725 toc01 TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY MAX9725 toc02 TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY VDD = 1V RL = 16Ω AV = -2V/V POUT = 0.7mW MAX9725 toc03 1 1 VDD = 1.5V RL = 1 6 Ω AV = -2V/V VDD = 1.5V RL = 32Ω AV = -2V/V 1 0.1 THD+N (%) POUT = 15mW THD+N (%) 0.1 POUT = 2mW THD+N (%) 0.1 0.01 POUT = 2mW 0.01 0.01 POUT = 4mW POUT = 12mW 0.001 10 100 1k FREQUENCY (Hz) 10k 100k 0.001 10 100 1k FREQUENCY (Hz) 10k 100k 0.001 10 100 1k FREQUENCY (Hz) 10k 100k 4 _______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Typical Operating Characteristics (continued) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise noted.) (See the Functional Diagrams.) TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY MAX9725 toc04 TOTAL HARMONIC DISTORTION PLUS NOISE vs. OUTPUT POWER MAX9725 toc05 TOTAL HARMONIC DISTORTION PLUS NOISE vs. OUTPUT POWER VDD = 1.5V RL = 32Ω AV = -2V/V fIN = 20Hz fIN = 1kHz MAX9725 toc06 1 VDD = 1V RL = 3 2 Ω AV = -2V/V 100 100 10 VDD = 1.5V RL = 16Ω AV = -2V/V fIN = 20Hz fIN = 1kHz 10 0.1 THD+N (%) THD+N (%) THD+N (%) POUT = 0.7mW 1 fIN = 10kHz 0.1 1 fIN = 10kHz 0.1 0.01 0.01 POUT = 4mW 0.001 10 100 1k FREQUENCY (Hz) 10k 100k 0.001 0 10 20 30 40 OUTPUT POWER (mW) 0.001 0 10 20 30 40 OUTPUT POWER (mW) 0.01 TOTAL HARMONIC DISTORTION PLUS NOISE vs. OUTPUT POWER MAX9725 toc07 TOTAL HARMONIC DISTORTION PLUS NOISE vs. OUTPUT POWER VDD = 1V RL = 32Ω AV = -2V/V MAX9725 toc08 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY -20 -30 -40 VDD = 1.5V RL = 3 2 Ω MAX9725 toc09 100 10 VDD = 1V RL = 1 6 Ω AV = -2V/V 100 fIN = 20Hz fIN = 1kHz -10 fIN = 20Hz fIN = 1kHz 10 THD+N (%) THD+N (%) fIN = 10kHz 0.1 fIN = 10kHz 0.1 PSRR (dB) 15 1 1 -50 -60 -70 -80 0.01 0.001 0 5 10 15 OUTPUT POWER (mW) 0.01 0.001 0 5 10 OUTPUT POWER (mW) -90 -100 -110 10 100 1k FREQUENCY (Hz) 10k 100k POWER-SUPPLY REJECTION RATIO vs. FREQUENCY MAX9725 toc10 CROSSTALK vs. FREQUENCY MAX9725 toc11 OUTPUT POWER vs. SUPPLY VOLTAGE 70 OUTPUT POWER (mW) 60 50 40 30 20 fIN = 1kHz RL = 16 Ω BOTH INPUTS DRIVEN IN-PHASE THD+N = 10% MAX9725 toc12 0 -10 -20 -30 PSRR (dB) 0 -20 -40 PSRR (dB) -60 -80 -100 VDD = 1V RL = 3 2 Ω VDD = 1.5V POUT = 5mW RL = 32Ω 80 -40 -50 -60 -70 -80 -90 -100 10 100 1k FREQUENCY (Hz) 10k 100k LEFT TO RIGHT RIGHT TO LEFT -120 10 100 1k FREQUENCY (Hz) 10k 100k 10 0 0.9 1.1 THD+N = 1% 1.3 1.5 SUPPLY VOLTAGE (V) _______________________________________________________________________________________ 5 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Typical Operating Characteristics (continued) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise noted.) (See the Functional Diagrams.) OUTPUT POWER vs. SUPPLY VOLTAGE MAX9725 toc13 OUTPUT POWER vs. LOAD RESISTANCE MAX9725 toc14 OUTPUT POWER vs. LOAD RESISTANCE 70 60 OUTPUT POWER (mW) 50 40 30 20 10 0 THD+N = 10% THD+N = 1% VDD = 1V fIN = 1kHz BOTH INPUTS DRIVEN IN-PHASE MAX9725 toc15 50 45 40 OUTPUT POWER (mW) 35 30 25 20 15 10 5 0 0.9 1.1 1.3 THD+N = 1% fIN = 1kHz R L = 3 2Ω BOTH INPUTS DRIVEN IN-PHASE THD+N = 10% 80 70 60 OUTPUT POWER (mW) THD+N = 10% 50 40 30 20 10 0 10 100 THD+N = 1% VDD = 1.5V fIN = 1kHz BOTH INPUTS DRIVEN IN-PHASE 80 1.5 1k 10 100 LOAD RESISTANCE (Ω) 1k SUPPLY VOLTAGE (V) LOAD RESISTANCE (Ω) POWER DISSIPATION vs. OUTPUT POWER MAX9725 toc16 POWER DISSIPATION vs. OUTPUT POWER MAX9725 toc17 GAIN FLATNESS vs. FREQUENCY 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 10 100 1k FREQUENCY (Hz) 10k 100k MAX9725 toc18 80 70 POWER DISSIPATION (mW) 60 50 40 30 20 10 0 0 10 20 30 40 RL = 32Ω VDD = 1.5V fIN = 1kHz POUT = POUTL + POUTR OUTPUTS IN-PHASE RL = 16Ω 35 30 POWER DISSIPATION (mW) 25 20 15 10 5 0 RL = 32Ω VDD = 1V fIN = 1kHz POUT = POUTL + POUTR OUTPUTS IN-PHASE 10 15 RL = 16Ω 50 0 5 20 OUTPUT POWER (mW) OUTPUT POWER (mW) AMPLITUDE (dB) OUTPUT POWER vs. CHARGE-PUMP CAPACITANCE AND LOAD RESISTANCE MAX9725 toc19 OUTPUT SPECTRUM vs. FREQUENCY MAX9725 toc20 SUPPLY CURRENT vs. SUPPLY VOLTAGE 4.5 4.0 SUPPLY CURRENT (mA) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 NO LOAD MAX9725 toc21 40 35 OUTPUT POWER (mW) 30 25 20 15 10 5 0 10 20 30 40 C1 = C2 = 0.68µF C1 = C2 = 0.47µF VDD = 1.5V fIN = 1kHz THD+N = 1% C1 = C2 = 2.2µF C1 = C2 = 1µF 0 -20 -40 AMPLITUDE (dB) -60 -80 -100 -120 -140 -160 0 5 10 FREQUENCY (kHz) 5.0 fIN = 1kHz RL = 32Ω VOUT = -60dBV VDD = 1.5V 50 15 20 0.9 1.0 1.1 1.2 1.3 1.4 1.5 LOAD RESISTANCE (Ω) SUPPLY VOLTAGE (V) 6 _______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Typical Operating Characteristics (continued) (VDD = 1.5V, PGND = SGND = 0V, VSHDN = 1.5V, VSS = PVSS, C1 = C2 = 1µF, CIN = 1µF, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise noted.) (See the Functional Diagrams.) SHUTDOWN CURRENT vs. SUPPLY VOLTAGE MAX9725 toc22 EXITING SHUTDOWN MAX9725 toc23 POWER-UP/-DOWN WAVEFORM MAX9725toc24 0.7 0.6 SHUTDOWN CURRENT (µA) 0.5 0.4 0.3 0.2 0.1 0 0.9 1.1 1.3 OUT_ 1V/div VDD 1V/div SHDN 500mV/div OUT_ 10mV/div 1.5 200µs/div 200ms/div SUPPLY VOLTAGE (V) Pin Description PIN THIN QFN 1 2 3 4 5 6 7 8 9 10 11 12 EP BUMP UCSP A1 A2 A3 A4 B4 B3 C4 C3 C2 C1 B1 B2 — NAME C1N PVSS INL INR VSS SGND OUTR OUTL VDD C1P PGND SHDN EP FUNCTION Flying Capacitor Negative Terminal. Connect a 1µF capacitor from C1P to C1N. Inverting Charge-Pump Output. Bypass with 1µF from PVSS to PGND. PVSS must be connected to Left-Amplifier Inverting Input. Connect input resister RIN from input capacitor C1N to INR (MAX9725E only). Right-Amplifier Inverting Input. Connect input resister RIN from input capacitor C1N to INR (MAX9725E only). Amplifier Negative Power Supply. Must be connected to PVSS. Signal Ground. SGND must be connected to PGND. SGND is the ground reference for the input and output signal. Right-Channel Output. Connect feedback resistor RFB between OUTR and INR (MAX9725E only). Left-Channel Output. Connect feedback resistor RFB between OUTL and INL (MAX9725E only). Positive Power-Supply Input. Bypass with a 1µF capacitor to PGND. Flying Capacitor Positive Terminal. Connect a 1µF capacitor from C1P to C1N. Power Ground. Ground reference for the internal charge pump. PGND must be connected to SGND. Active-Low Shutdown. Connect to VDD for normal operation. Pull low to disable the amplifier and charge pump. Exposed Paddle. Internally connected to VSS. Leave paddle unconnected or solder to VSS. _______________________________________________________________________________________ 7 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Detailed Description The MAX9725 stereo headphone driver features Maxim’s patented DirectDrive architecture, eliminating the large output-coupling capacitors required by conventional single-supply headphone drivers. The MAX9725 consists of two 20mW class AB headphone drivers, shutdown control, inverting charge pump, internal gain-setting resistors, and comprehensive click-and-pop suppression circuitry (see the Functional Diagram). A negative power supply (PVSS) is created by inverting the positive supply (VDD). Powering the drivers from VDD and PVSS increases the dynamic range of the drivers to almost twice that of other 1V single-supply drivers. This increase in dynamic range allows for higher output power. The outputs of the MAX9725 are biased about GND (Figure 1). The benefit of this GND bias is that the driver outputs do not have a DC component, thus large DCblocking capacitors are unnecessary. Eliminating the DC-blocking capacitors on the output saves board space, system cost, and improves frequency response. Previous attempts to eliminate the output-coupling capacitors involved biasing the headphone return (sleeve) to the DC-bias voltage of the headphone amplifiers. This method raises some issues: • The sleeve is typically grounded to the chassis. Using this biasing approach, the sleeve must be isolated from system ground, complicating product design. During an ESD strike, the driver’s ESD structures are the only path to system ground. The driver must be able to withstand the full ESD strike. When using the headphone jack as a line out to other equipment, the bias voltage on the sleeve may conflict with the ground potential from other equipment, resulting in possible damage to the drivers. • • DirectDrive Conventional single-supply headphone drivers have their outputs biased about a nominal DC voltage (typically half the supply) for maximum dynamic range. Large coupling capacitors are needed to block the DC bias from the headphones. Without these capacitors, a significant amount of DC current flows to the headphone, resulting in unnecessary power dissipation and possible damage to both headphone and headphone driver. Maxim’s DirectDrive architecture uses a charge pump to create an internal negative supply voltage. This allows the MAX9725 outputs to be biased about GND, increasing the dynamic range while operating from a single supply. A conventional amplifier powered from 1.5V ideally provides 18mW to a 16 Ω load. The MAX9725 provides 25mW to a 16 Ω load. The DirectDrive architecture eliminates the need for two large (220µF, typ) DC-blocking capacitors on the output. The MAX9725 charge pump requires two small ceramic capacitors, conserving board space, reducing cost, and improving the frequency response of the headphone driver. See the Output Power vs. ChargePump Capacitance and Load Resistance graph in the Typical Operating Characteristics for details of the possible capacitor sizes. VOUT VDD VDD / 2 GND CONVENTIONAL DRIVER-BIASING SCHEME VDD VOUT GND -VDD DirectDrive BIASING SCHEME Figure 1. Traditional Driver Output Waveform vs. MAX9725 Output Waveform (Ideal Case) 8 _______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 LF ROLLOFF (16Ω LOAD) 0 -3 -5 ATTENUATION (dB) -10 100µF -15 33µF -20 -25 -30 -35 10 100 FREQUENCY (Hz) 1k 0.001 ALUM/ELEC 0.0001 10 100 1k FREQUENCY (Hz) 10k 100k 330µF 220µF THD+N (%) -3dB CORNER FOR 100µF IS 100Hz 1 10 ADDITIONAL THD+N DUE TO DC-BLOCKING CAPACITORS 0.1 TANTALUM 0.01 Figure 2. Low-Frequency Attenuation for Common DC-Blocking Capacitor Values Figure 3. Distortion Contributed By DC-Blocking Capacitors Low-Frequency Response Large DC-blocking capacitors limit the amplifier’s lowfrequency response and can distort the audio signal: 1) The impedance of the headphone load and the DCblocking capacitor forms a highpass filter with the -3dB point set by: f-3dB = 1 2πRLCOUT voltage coefficient appears as frequency-dependent distortion. Figure 3 shows the THD+N introduced by two different capacitor dielectric types. Note that below 100Hz, THD+N increases rapidly. The combination of low-frequency attenuation and frequency-dependent distortion compromises audio reproduction in portable audio equipment that emphasizes low-frequency effects such as multimedia laptops, as well as MP3, CD, and DVD players. These low-frequency, capacitor-related deficiencies are eliminated by using DirectDrive technology. Charge Pump The MAX9725 features a low-noise charge pump. The 580kHz switching frequency is well beyond the audio range, and does not interfere with the audio signals. The switch drivers feature a controlled switching speed that minimizes noise generated by turn-on and turn-off transients. The di/dt noise caused by the parasitic bond wire and trace inductance is minimized by limiting the turn-on/off speed of the charge pump. Additional highfrequency noise attenuation can be achieved by increasing the size of C2 (see the Functional Diagram). Extra noise attenuation is not typically required. where RL is the impedance of the headphone and COUT is the value of the DC-blocking capacitor. The highpass filter is required by conventional singleended, single power-supply headphone drivers to block the midrail DC-bias component of the audio signal from the headphones. The drawback to the filter is that it can attenuate low-frequency signals. Larger values of COUT reduce this effect but result in physically larger, more expensive capacitors. Figure 2 shows the relationship between the size of COUT and the resulting low-frequency attenuation. Note that the -3dB point for a 16Ω headphone with a 100µF blocking capacitor is 100Hz, well within the normal audio band, resulting in low-frequency attenuation of the reproduced signal. 2) The voltage coefficient of the DC-blocking capacitor contributes distortion to the reproduced audio signal as the capacitance value varies when the function of the voltage across the capacitor changes. At low frequencies, the reactance of the capacitor dominates at frequencies below the -3dB point and the Shutdown The MAX9725’s low-power shutdown mode reduces supply current to 0.6µA. Driving SHDN low disables the amplifiers and charge pump. The driver’s output impedance is typically 50k Ω (MAX9725A), 37.5k Ω (MAX9725B), 25kΩ (MAX9725C), 100kΩ (MAX9725D), or RF (MAX9725E) when in shutdown mode. 9 _______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 OUTPUT POWER vs. SUPPLY VOLTAGE WITH INPUTS IN- AND OUT-OF-PHASE 50 45 40 OUTPUT POWER (mW) 35 30 25 20 15 10 5 0 0.9 1.1 1.3 1.5 SUPPLY VOLTAGE (V) INPUTS IN-PHASE fIN = 1kHz RL = 16Ω THD+N = 1% INPUTS 180° OUT-OF-PHASE Applications Information Power Dissipation Linear power amplifiers can dissipate a significant amount of power under normal operating conditions. The maximum power dissipation for each package is given in the Absolute Maximum Ratings section under Continuous Power Dissipation or can be calculated by the following equation: PDISSPKG(MAX) = TJ(MAX) - TA θ JA Figure 4. Output Power vs. Supply Voltage with Inputs In-/Outof-Phase Click-and-Pop Suppression In conventional single-supply audio drivers, the outputcoupling capacitor is a major contributor of audible clicks and pops. Upon startup, the driver charges the coupling capacitor to its bias voltage, typically half the supply. Likewise, on shutdown, the capacitor is discharged to GND. This results in a DC shift across the capacitor that appears as an audible transient at the speaker. The MAX9725’s DirectDrive technology eliminates the need for output-coupling capacitors. The MAX9725 also features extensive click-and-pop suppression that eliminates any audible transient sources internal to the device. The Power-Up/Down Waveform in the T ypical Operating Characteristics shows minimal DC shift and no spurious transients at the output upon startup or shutdown. In most applications, the output of the preamplifier driving the MAX9725 has a DC bias of typically half the supply. At startup, the input-coupling capacitor is charged to the preamplifier’s DC bias voltage through the internal input resistor (25k Ω for MAX9725AMAX9725D, minimum 10kΩ for MAX9725E) causing an audible click and pop. Delaying the rise of SHDN 4 or 5 time constants, based on RIN x CIN, relative to the startup of the preamplifier eliminates any click and pop caused by the input filter (see the Functional Diagram). where TJ(MAX) is +150°C, TA is the ambient temperature, and θJA is the reciprocal of the derating factor in °C/W as specified in the Absolute Maximum Ratings section. For example, θJA for the thin QFN package is +59.3°C/W. The MAX9725 has two power dissipation sources, the charge pump and the two amplifiers. If the power dissipation exceeds the rated package dissipation, reduce VDD, increase load impedance, decrease the ambient temperature, or add heatsinking to the device. Large output, supply, and ground traces decrease θJA, allowing more heat to be transferred from the package to surrounding air. Output Power The MAX9725’s output power increases when the left and right audio signals differ in magnitude and/or phase. Figure 4 shows the two extreme cases for inand out-of-phase input signals. The output power of a typical stereo application lies between the two extremes shown in Figure 4. The MAX9725 is specified to output 20mW per channel when both inputs are in-phase. Powering Other Circuits from the Negative Supply The MAX9725 internally generates a negative supply voltage (PVSS) to provide the ground-referenced output signal. Other devices can be powered from PVSS provided the current drawn from the charge pump does not exceed 1mA. Headphone driver output power and THD+N will be adversely affected if more than 1mA is drawn from PVSS. Using PVSS as an LCD bias is a typical application for the negative supply. PVSS is unregulated and proportional to VDD. Connect a 1µF capacitor from C1P to C1N for best charge-pump operation. 10 ______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown Component Selection Input Filtering The AC-coupling capacitor (CIN) and an internal gainsetting resistor form a highpass filter that removes any DC bias from an input signal (see the F unctional Diagram). C IN allows the MAX9725A–MAX9725D to bias the signal to an optimum DC level. The -3dB point of the highpass filter, assuming zero source impedance, is given by: f-3dB = 1 2π × RIN × CIN Hold Capacitor (C2) The hold capacitor’s value and ESR directly affect the ripple at PVSS. Increasing the value of C2 reduces ripple. Choosing a capacitor with lower ESR reduces ripple and output impedance. Lower capacitance values can be used in systems with low maximum output power levels. See the Output Power vs. Charge-Pump Capacitance and Load Impedance graph in the Typical Operating Characteristics. Power-Supply Bypass Capacitor (C3) The power-supply bypass capacitor (C3) lowers the output impedance of the power supply and reduces the impact of the MAX9725’s charge-pump switching transients. Bypass VDD to PGND with the same value as C1. Place C3 as close to VDD as possible. MAX9725 Choose CIN so f-3dB is well below the lowest frequency of interest. RIN for the MAX9725A–MAX9725D is 25kΩ and a minimum of 10kΩ for the MAX9725E. Setting f-3dB too high affects the amplifier’s low-frequency response. Use capacitors with low-voltage coefficient dielectrics. Film or C0G dielectric capacitors are good choices for AC-coupling capacitors. Capacitors with high-voltage coefficients, such as ceramics, can result in increased distortion at low frequencies. Charge-Pump Capacitor Selection Use capacitors with less than 100mΩ of ESR. Low-ESR ceramic capacitors minimize the output impedance of the charge pump. Capacitors with an X7R dielectric provide the best performance over the extended temperature range. Table 1 lists suggested capacitor manufacturers. Flying Capacitor (C1) The value of C1 affects the charge pump’s load regulation and output impedance. Choosing C1 too small degrades the MAX9725’s ability to provide sufficient current drive and leads to a loss of output voltage. Increasing the value of C1 improves load regulation and reduces the charge-pump output impedance. See the Output Power vs. Charge-Pump Capacitance and Load Impedance graph in the T ypical Operating Characteristics. Layout and Grounding Proper layout and grounding are essential for optimum performance. Connect PGND and SGND together at a single point on the PC board. Connect PVSS to SVSS and bypass with C2 to PGND. Bypass VDD to PGND with C3. Place capacitors C2 and C3 as close to the MAX9725 as possible. Route PGND, and all traces that carry switching transients, away from SGND and the audio signal path. The MAX9725 does not require additional heatsinking. The thin QFN package features an exposed paddle that improves thermal efficiency of the package. Ensure the exposed paddle is electrically isolated from GND and VDD. Connect the exposed paddle to VSS if necessary. UCSP Applications Information For the latest application details on UCSP construction, dimensions, tape carrier information, printed circuit board techniques, bump-pad layout , and recommended reflow temperature profile, as well as the latest information on reliability testing results, go to Maxim’s website at www.maxim-ic.com/ucsp for the Application Note: UCSP—A Wafer-Level Chip-Scale Package. Table 1. Suggested Capacitor Manufacturers SUPPLIER Murata Taiyo Yuden TDK PHONE 770-436-1300 800-348-2496 847-803-6100 FAX — 847-925-0899 847-390-4405 WEBSITE www.murata.com www.t-yuden.com www.component.tdk.com ______________________________________________________________________________________ 11 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 System Diagrams 0.9V TO 1.8V 1µF 1µF MP3 DECODER STEREO DAC 1µF C1P 1µF C1N VSS PVSS 1µF INR INL SHDN VDD MAX9725A– MAX9725D OUTR OUTL SGND PGND RF MAX9725E 1µF RIN INL VDD SHDN OUTL 1µF C1N 1µF 1µF RIN DIN INR CHARGE PUMP PVSS 1µF VSS OUTR SGND PGND RF 12 ______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown Functional Diagrams MAX9725 0.9V TO 1.8V LEFTCHANNEL AUDIO IN CIN 0.47µF C3 1µ F 9 (C2) VDD 12 (B2) SHDN 3 (A3) INL R F* RIN 25kΩ VDD 8 OUTL (C3) 10 (C1) C1P UVLO/ SHUTDOWN CONTROL SGND HEADPHONE JACK VSS C1 1µ F 1 (A1) C1N CHARGE PUMP CLICK-AND-POP SUPPRESSION VDD SGND 7 (C4) MAX9725A– MAX9725D RIN 25kΩ VSS R F* PVSS 2 (A2) C2 1µ F VSS 5 (B4) PGND 11 (B1) SGND 6 (B3) CIN 0.47µF LEFTCHANNEL AUDIO IN INR 4 (A4) OUTR *MAX9725A = 50kΩ. MAX9725B = 37.5kΩ. MAX9725C = 25kΩ. MAX9725D = 100kΩ. ( ) DENOTE BUMPS FOR UCSP. ______________________________________________________________________________________ 13 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Functional Diagrams (continued) LEFT-CHANNEL AUDIO IN 0.9V TO 1.8V RIN 1µ F 9 (C2) VDD 12 (B2) SHDN 3 (A3) INL RF VDD 8 OUTL (C3) UVLO/ SHUTDOWN CONTROL SGND HEADPHONE JACK VSS C3 1µ F 10 (C1) C1P C1 1µ F 1 (A1) C1N CHARGE PUMP CLICK-AND-POP SUPPRESSION VSS SGND 7 (C4) MAX9725E OUTR VDD RF PVSS 2 (A2) C2 1µ F VSS 5 (B4) PGND 11 (B1) SGND 6 (B3) INR 4 (A4) RIN CIN 1µ F *MAX9725A = 50kΩ. MAX9725B = 37.5kΩ. MAX9725C = 25kΩ. MAX9725D = 100kΩ. ( ) DENOTE BUMPS FOR UCSP. RIGHTCHANNEL AUDIO IN 14 ______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown Pin Configurations TOP VIEW (BUMP-SIDE DOWN) A C1N B PGND C C1P VDD OUTL SHDN SGND VSS PGND 11 OUTR SHDN 12 PVSS INL INR C1P 10 6 SGND MAX9725 1 2 3 4 TOP VIEW 9 8 OUTR 7 OUTL MAX9725 VDD MAX9725 + *EP 5 VSS 4 INR UCSP 1 C1N 2 PVSS 3 INL THIN QFN *EP = EXPOSED PAD. Block Diagrams (continued) Ordering Information (continued) PART PINPACKAGE 12 TQFN-EP* 12 UCSP-12 12 TQFN-EP* 12 UCSP-12 12 TQFN-EP* 12 UCSP-12 12 TQFN-EP* PKG CODE T1244-4 B12-1 T1244-4 B12-1 T1244-4 B12-1 T1244-4 TOP MARK +AAEX +ACM +AAEY +ACN +AAEZ +AEF +AAGH GAIN (V/V) -1.5 -1 -1 -4 -4 ADJ ADJ VDD RFB C3 SINGLE 1.5V CELL AA OR AAA BATTERY DirectDrive OUTPUTS ELIMINATE DC-BLOCKING CAPACITORS. MAX9725BETC+ MAX9725CEBC+T MAX9725CETC+ MAX9725DEBC+T MAX9725DETC+ MAX9725EEBC+T MAX9725EETC+** MAX9725E INL OUTL C1P INVERTING CHARGE PUMP C1N PVSS C2 VSS Note: All devices are specified over the -40°C to +85°C operating temperature range. +Denotes a lead-free package. T = Tape and reel. *EP = Exposed pad. **Future product—contact factory for availability. INR OUTR Chip Information RFB SGND PGND TRANSISTOR COUNT: 2559 PROCESS: BiCMOS ______________________________________________________________________________________ 15 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) PACKAGE OUTLINE, 4x3 UCSP 21-0104 F 1 1 16 ______________________________________________________________________________________ 12L, UCSP 4x3.EPS 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 24L QFN THIN.EPS MAX9725 ______________________________________________________________________________________ 17 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown MAX9725 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 18 ______________________________________________________________________________________ 1V, Low-Power, DirectDrive, Stereo Headphone Amplifier with Shutdown Revision History REVISION NUMBER 0 1 2 REVISION DATE 11/04 5/05 11/07 Initial release Removed future product asterisks for UCSP package, added EC table note Added MAX9725E packages, MAX9725E EC table, block diagram, functional diagram, and system diagram. Updated package outlines. DESCRIPTION PAGES CHANGED — 1–3, 13, 14 1–3, 6, 8–19 MAX9725 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 © 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.