MXL1013DN8

19-0133; Rev. 3; 4/98 Dual/Quad Precision Op Amps General Description The Maxim MXL1013 is a precision dual op amp that upgrades the performance of popular devices such as the MC1458/MC1558, LM158 and OP221. The Maxim MXL1014 is a precision quad op amp that directly upgrades designs in the industry-standard 14-pin DIP configuration and has specifications similar to the LT1013. The MXL1013 and MXL1014 are pin compatible with industry standards such as the LT1013 and LT1014. Precision specifications include: 40µV offset voltage, 0.3µV/°C drift (TCVOS), 117dB CMRR, and 120dB PSRR. While supply current is typically only 350µA per amplifier, the outputs can source and sink more than 20mA. Both the MXL1013 and the MXL1014 can be operated from a single +5V power supply. The input voltage range includes ground and the outputs swing to within a few millivolts of ground. ____________________________Features o Single-Supply Operation Input Voltage Range Extends to Ground Output Swings to Ground while Sinking Current o 150µV Max Offset Voltage o Low Drift: 2µV/°C Max o 0.8nA Max Offset Current o Guaranteed High Gain 5mA Load Current: 1.5 Million Min 17mA Load Current: 0.8 Million Min o 500µA Max Supply Current per Amplifier o Low Voltage Noise: 0.1Hz to 10Hz, 0.55µVp-p o Lower Current Noise than OP07: 0.07 pA/√Hz MXL1013/MXL1014 Ordering Information PART MXL1013CN8 MXL1013DN8 MXL1013DS8 MXL1013DC/D MXL1013IN8 MXL1013IS8 MXL1013AMJ8 MXL1013MJ8 TEMP. RANGE 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C -55°C to +125°C -55°C to +125°C PIN-PACKAGE 8 Plastic DIP 8 Plastic DIP 8 SO Dice* 8 Plastic DIP 8 SO 8 CERDIP** 8 CERDIP** ________________________Applications Battery-Powered Precision Instrumentation Strain-Gauge Signal Conditioners Thermocouple Amplifiers Instrumentation Amplifiers 4mA to 20mA Current-Loop Transmitters Multiple-Limit Threshold Detection Active Filters Multiple Gain Blocks Ordering Information continued on last page. * Dice are specified at TA = +25°C, D.C. parameters only. **Contact factory for availability and processing to MIL-STD-883. Pin Configurations TOP VIEW OUTA 1 INA- 2 A INA+ VINB+ INB1 2 3 4 B 16 15 D 14 OUTD INDIND+ VINC+ INCOUTC N.C. MXL1013 A 8 7 6 5 INAOUTA V+ OUTB OUTA+ INAINA+ V- 1 2 A MXL1013 8 7 6 INA+ 3 V+ OUTB INBINB+ V+ 4 INB+ 5 INB- 6 OUTB 7 B MXL1014 C 13 12 11 10 9 3 4 B 5 SO NOTE: SO PIN CONFIGURATION DIFFERS FROM DIP. DIP N.C. 8 Wide SO Pin Configurations continued on last page. _________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769. Dual/Quad Precision Op Amps MXL1013/MXL1014 ABSOLUTE MAXIMUM RATINGS Supply Voltage.....................................................................±22V Input Voltage ............................Equal to Positive Supply Voltage ........................5V Below Negative Supply Voltage Output Short-Circuit Duration.....................................Continuous Differential Input Voltage .....................................................±30V Continuous Power Dissipation (TA = +70°C) 8-Pin Plastic DIP (derate 9.09mW/°C above +70°C)......727mW 8-Pin SO (derate 5.88mW/°C above +70°C) ..................471mW 8-Pin CERDIP (derate 8.00mW/°C above +70°C) ..........640mW 14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)..800mW 14-Pin CERDIP (derate 9.09mW/°C above +70°C) ........727mW 16-Pin Wide SO (derate 9.52mW/°C above +70°C).......762mW Operating Temperature Ranges: MXL1013/MXL1014C_ ........................................0°C to +70°C MXL1013/MXL1014I_.......................................-40°C to +85°C MXL1013/MXL1014AM_,M_ ..........................-55°C to +125°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Note 1) (VS = ±15V, VCM = 0V, TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MXL1013 Input Offset Voltage VOS MXL1014 MXL101_D/I Long-Term Input Offset Voltage Stability Input Offset Current Input Bias Current Input Noise Voltage Input Noise-Voltage Density Input Noise-Current Density Input Resistance (Note 2) Large-Signal Voltage Gain Input Voltage Range -15.0 Common-Mode Rejection Ratio CMRR VCM = +13.5V, -15.0V 100 -15.3 117 -15.0 97 -15.3 114 dB IOS IB en en 0.1Hz to 10Hz fO = 10Hz fO = 1000Hz fO = 10Hz Differential Common mode AVOL VO = ±10V, RL = 2kΩ VO = ±10V, RL = 600Ω 1.5 0.8 +13.5 100 0.4 0.15 12 0.55 24 22 0.07 400 5 8.0 2.5 +13.8 1.2 0.5 +13.5 70 0.80 20 MXL1013AM MXL1014AM MIN TYP MAX 40 50 150 180 MXL1013C/D/I/M MXL1014C/D/I/M MIN TYP MAX 60 60 200 0.5 0.2 15 0.55 24 22 0.07 300 4 7.0 V/µV 2.0 +13.8 V 1.5 30 300 300 800 µV/Mo. nA nA µVp-p nV/√Hz pA/√Hz MΩ GΩ µV UNITS in 2 _______________________________________________________________________________________ Dual/Quad Precision Op Amps ELECTRICAL CHARACTERISTICS (continued) (Note 1) (VS = ±15V, VCM = 0V, TA = +25°C, unless otherwise noted.) MXL1013AM MXL1014AM MIN TYP MAX 103 123 ±13 0.2 IS Per amplifier 120 140 ±14 0.4 0.35 0.50 MXL1013C/D/I/M MXL1014C/D/I/M MIN TYP MAX 100 120 ±12.5 0.2 117 137 ±14 0.4 0.35 0.55 MXL1013/MXL1014 PARAMETER SYMBOL CONDITIONS UNITS Power-Supply Rejection Ratio Channel Separation Output Voltage Swing Slew Rate Supply Current Note 1: Note 2: PSRR VS = ±2V to ±18V VO = ±10V, RL = 2kΩ dB dB V V/µs mA VOUT RL = 2kΩ When amplifier is sinking current at the output a minimum load of 1kΩ is recommended. Guaranteed by design. ELECTRICAL CHARACTERISTICS (Note 1) (VS+ = +5V, VS- = 0V, VOUT = +1.4V, VCM = 0V, TA = +25°C, unless otherwise noted.) MXL1013AM MXL1014AM MIN TYP MAX 60 70 250 280 MXL1013C/D/I/M MXL1014C/D/I/M MIN TYP MAX 90 90 250 0.2 15 VO = 5mV to 4V, RL =500Ω +3.5 0 Output low, no load Output low, 600Ω to ground Output Voltage Swing VOUT Output low, ISINK = 1mA Output high, no load Output high, 600Ω to ground Supply Current IS Per amplifier 4.0 3.4 1.0 +3.8 -0.3 15 5 220 4.4 4.0 0.31 0.45 25 10 350 4.0 3.4 +3.5 0 1.3 35 0.3 18 1.0 +3.8 -0.3 15 5 220 4.4 V 4.0 0.32 0.50 mA 25 10 350 mV 450 450 950 2.0 50 nA nA V/µV V µV PARAMETER SYMBOL CONDITIONS MXL1013 UNITS Input Offset Voltage VOS MXL1014 MXL101_D/I Input Offset Current Input Bias Current Large-Signal Voltage Gain Input Voltage Range IOS IB AVOL _______________________________________________________________________________________ 3 Dual/Quad Precision Op Amps MXL1013/MXL1014 ELECTRICAL CHARACTERISTICS (Note 1) (VS = ±15V, VCM = 0V, TA = -40°C to +85°C for MXL1013I and MXL1014I, TA = 0°C to +70°C for MXL1013C/D and MXL1014C/D, unless otherwise noted.) MXL1013C/D/I MXL1014C/D/I MIN TYP MAX 80 230 110 400 1000 570 µV PARAMETER SYMBOL CONDITIONS MXL101_C MXL101_D/I UNITS Input Offset Voltage VOS MXL101_C: VS = 5V, 0V, VO = 1.4V MXL101_D/I: VS = 5V, 0V; VO =1.4V (Note 2) 280 0.4 0.7 0.3 1200 2.5 µV/°C 5.0 2.8 nA 6.0 38 90 nA V/µV dB dB V 13 mV V 0.60 mA 0.55 Input Offset-Voltage Drift TCVOS MXL101_D/I (Note 2) Input Offset Current IOS VS = 5V, 0V; VO = 1.4V 0.5 16 Input Bias Current Large-Signal Voltage Gain Common-Mode Rejection Ratio Power-Supply Rejection Ratio IB AVOL CMRR PSRR VS = 5V, 0V; VO = 1.4V VO = ±10V, RL = 2kΩ VCM = +13.0V, -15.0V VS = ±2V to ±18V RL = 2kΩ 0.7 94 97 ±12.0 Output low Output high 3.2 24 4.0 113 116 ±13.9 6 3.9 0.37 Output Voltage Swing VOUT VS = 5V,0V, RL = 600Ω Supply Current per Amplifier IS VS = 5V, 0V, VO = 1.4V 0.34 4 _______________________________________________________________________________________ Dual/Quad Precision Op Amps ELECTRICAL CHARACTERISTICS (Note 1) (VS = ±15V, VCM = 0V, TA = -55°C to +125°C, unless otherwise noted.) MXL1013AM MIN TYP MAX 80 TA = -55°C to +100°C (Note 3) Input Offset Voltage VOS VS = 5V, 0V, VO = 1.4V TA = +125°C, VCM = 0.1V TA = +125°C, VCM = 0V 80 120 250 0.4 0.3 IOS VS = 5V, 0V; VO = 1.4V IB 0.6 15 VS = 5V, 0V; VO = 1.4V VO = ±10V, RL = 2kΩ VCM = +13.0V, -14.9V 0.5 20 2.0 6.0 30 80 0.4 0.7 15 25 2.0 7.0 30 90 0.25 0.9 18 28 2.0 10.0 45 nA 120 V/µV 300 450 450 900 2.0 2.5 MXL1014AM MIN TYP MAX 90 90 150 300 0.4 0.3 350 480 480 960 2.0 2.8 MXL1013M MXL1014M MIN TYP MAX 110 100 200 400 0.5 0.4 550 750 750 1500 2.5 5.0 nA µV/°C µV MXL1013/MXL1014 PARAMETER SYMBOL CONDITIONS UNITS Input OffsetVoltage Drift Input Offset Current Input Bias Current Large-Signal Voltage Gain CommonMode Rejection Ratio Power-Supply Rejection Ratio TCVOS (Note 2) AVOL CMRR 97 114 96 114 94 113 dB PSRR VS = ±2V to ±18V RL = 2kΩ 100 117 100 117 97 116 dB V 18 mV ±12.0 ±13.8 Output low 6 15 ±12.0 ±13.8 6 15 ±11.5 ±13.8 6 Output Voltage Swing VOUT VS = 5V,0V, RL = 600Ω to ground Output high 3.2 3.8 0.38 0.60 0.55 3.2 3.8 0.38 0.34 0.60 0.55 3.1 3.8 0.38 0.34 0.70 V Supply Current per Amplifier IS VS = 5V, 0V; VO = 1.4V 0.34 0.65 mA Note 1: When amplifier is sinking current at the output, a minimum load of 1kΩ is recommended. Note 2: Guaranteed by design. Note 3: This parameter is guaranteed by design and is not tested. _______________________________________________________________________________________ 5 Dual/Quad Precision Op Amps MXL1013/MXL1014 __________________________________________Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) COMMON-MODE REJECTION RATIO vs. FREQUENCY 120 POWER-SUPPLY REJECTION RATIO (dB) 100 80 60 40 20 0 0.1 VS = ±15V+1Vp-p SINE WAVE NEGATIVE SUPPLY POSITIVE SUPPLY SUPPLY CURRENT PER AMPLIFIER (µA) 120 COMMON-MODE REJECTION RATIO (dB) 100 80 60 40 20 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY 460 SUPPLY CURRENT vs. TEMPERATURE 420 VS = ±15V VS = +5V,0V 380 VS = ±15V 340 VS = +5V, 0V 300 0 10 100 1k 10k 100k 1M 1 10 100 1k 10k 100k 1M 260 -50 -25 0 25 50 75 100 125 FREQUENCY (Hz) FREQUENCY (Hz) TEMPERATURE (°C) NOISE SPECTRUM 1000 VS = ±2V TO ±18V VOLTAGE NOISE DENSITY (nV/√Hz) CURRENT NOISE DENSITY (fA/√Hz) 300 VOLTAGE GAIN (dB) 10 20 GAIN, PHASE vs. FREQUENCY 80 VCM =0V CL = 100pF 100 PHASE ±15V GAIN 0 +5V, 0V ±15V 120 140 160 +5V, 0V 180 200 PHASE SHIFT (DEGREES) 140 120 100 VOLTAGE GAIN (dB) 80 60 40 20 0 0.3 1 FREQUENCY (MHz) 3 10 VOLTAGE GAIN vs. FREQUENCY CL = 100pF 100 CURRENT NOISE 30 VOLTAGE NOISE 1/f CORNER 2Hz VS = +5V,0V VS = ±15V -10 10 1 10 100 1k 0.1 FREQUENCY (Hz) -20 0.01 0.1 1 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 0.1Hz to 10Hz NOISE NOISE VOLTAGE (200nV/div) SMALL-SIGNAL TRANSIENT RESPONSE (VS = ±15V) LARGE-SIGNAL TRANSIENT RESPONSE (VS = ±15V) VOLTAGE (20mV/div) 0 2 4 6 8 10 TIME (2µs/div) AV = +1 AV = +1 TIME (50µs/div) TIME (sec) 6 ______________________________________________________________________________________ VOLTAGE (5V/div) Dual/Quad Precision Op Amps ____________________________Typical Operating Characteristics (continued) SMALL-SIGNAL TRANSIENT RESPONSE (VS = 5V, 0V) LARGE-SIGNAL TRANSIENT RESPONSE (VS = 5V, 0V) LARGE-SIGNAL TRANSIENT RESPONSE (VS = 5V, 0V) MXL1013/MXL1014 4V 100mV 2V 50mV 0v 0v TIME (20µs/div) AV = +1 RL = 600Ω to GND TIME (10µs/div) AV = +1 RL = 4.7kΩ to 5V 4V 2V 0v TIME (10µs/div) AV = +1 No load _____Pin Configurations (continued) OUTA 1 INA- 2 INA+ 3 V+ 4 INB+ 5 INB- 6 OUTB 7 A D 14 13 12 11 OUTD INDIND+ VINC+ INCOUTC ___________________Chip Topography 0.099" (2.514 mm) OUTA V+ OUTB MXL1014 B C 10 9 8 DIP INAINB- _Ordering Information (continued) PART MXL1014CN MXL1014DS MXL1014DN MXL1014IN MXL1014IS MXL1014AMJ MXL1014MJ TEMP. RANGE 0°C to +70°C 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C -55°C to +125°C -55°C to +125°C PIN-PACKAGE 14 Plastic DIP 16 Wide SO 14 Plastic DIP 14 Plastic DIP 16 Wide SO 14 CERDIP** 14 CERDIP** 0.085" (2.16 mm) INA+ INB+ V- **Contact factory for availability and processing to MIL-STD-883. _______________________________________________________________________________________ 7 Dual/Quad Precision Op Amps MXL1013/MXL1014 _______________________________________________________Package Information PDIPN.EPS Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 1998 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.