SF14M-TP

NOT RECOMMENDED FOR NEW DESIGNS MCC TM Micro Commercial Components
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# Features • • • • • • • SF11M Lead Free Finish/RoHS Compliant(Note 1) ("P" Suffix designates RoHS Compliant. See ordering information) High Surge Capability Low Leakage Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Super Fast Switching Speed For High Efficiency Halogen free available upon request by adding suffix "-HF" THRU SF18M 1 Amp Glass Passivated Super Fast Recovery Rectifier 50 to 600 Volts Maximum Ratings • • DO-214AC (HSMA) (High Profile) Operating Temperature: -65°C to +150°C Storage Temperature: -65°C to +150°C H MCC Catalog Number SF11M SF12M SF13M SF14M SF15M SF16M SF18M Device Marking SF11 SF12 SF13 SF14 SF15 SF16 SF18 Maximum Recurrent Peak Reverse Voltage 50V 100V 150V 200V 300V 400V 600V Maximum RMS Voltage 35V 70V 105V 140V 210V 280V 420V Maximum DC Blocking Voltage 50V 100V 150V 200V 300V 400V 600V Cathode Band J A E D B F Electrical Characteristics @ 25°C Unless Otherwise Specified IF(AV) 1A Average Forward TA = 55°C Current Peak Forward Surge IFSM 30A 8.3ms, half sine Current Maximum Instantaneous Forward Voltage .975V IFM = 1.0A; SF11M-SF15M VF 1.75V TA = 25°C SF16M-SF18M Maximum DC Reverse Current At IR 5µA TA = 25°C Rated DC Blocking 50µA TA = 150°C Voltage Maximum Reverse Recovery Time Trr 35ns IF=0.5A, IR=1.0A, SF11M-SF15M SF16M-SF18M 50ns Irr=0.25A Typical Junction Capacitance 15pF Measured at SF11M-SF15M CJ 10pF 1.0MHz, VR=4.0V SF16M-SF18M *Pulse Test: Pulse Width 300µsec, Duty Cycle 1% C G DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 NOTE SUGGESTED SOLDER PAD LAYOUT www.mccsemi.com 0.090” 0.085” 0.070” Notes: 1. High Temperature Solder Exemption Applied, see EU Directive Annex Notes 7. Revision: B 1 of 4 2013/01/01 MCC SF11M thru SF18M Figure 1 Typical Forward Characteristics Micro Commercial Components 20 Figure 2 Forward Derating Curve 10 1.5 6 4 1.25 2 25°C Amps 1.0 1 .6 .75 Amps .4 SF11M - SF15M .5 .2 SF16M - SF18M .25 .1 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 °C .02 .01 .4 .6 .8 1.0 1.2 Average Forward Rectified Current - Amperesversus Ambient Temperature -°C 1.4 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 SF11M - SF15M 20 pF TJ=25°C 10 SF16M - SF18M 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 Junction Capacitance - pFversus Reverse Voltage - Volts Revision: B www.mccsemi.com 2 of 4 2013/01/01 TM MCC SF11M thru SF18M Figure 4 Typical Reverse Characteristics Micro Commercial Components 100 Figure 5 Peak Forward Surge Current 60 60 40 20 50 TA=150°C 40 10 30 6 Amps 4 2 TA=100°C 20 10 5 0 µAmps 1 .6 1 4 2 6 20 40 60 80 100 Cycles .4 Peak Forward Surge Current - Amperes versus Number Of Cycles At 60Hz - Cycles .2 .1 8 10 TA=25°C .06 .04 .02 .01 20 40 60 80 100 120 140 Volts Instantaneous Reverse Leakage Current - MicroAmperesversus Percent Of Rated Peak Reverse Voltage - Volts Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Oscilloscope Note 1 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Revision: B -0.25 www.mccsemi.com 3 of 4 2013/01/01 TM MCC TM Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 3Kpcs/Reel Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. Revision: B www.mccsemi.com 4 of 4 2013/01/01