SP-750-15

750W Single Output Power Supply Features : Universal AC input / Full range SP-750 AC input active surge current limiting Built-in active PFC function,PF>0.96 series Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC ball bearing fan High power density 5.48/inch3 Built-in constant current limiting circuit With power good and fail signal output Built-in remote ON-OFF control Built-in remote sense function 3 years warranty SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE FUNCTION POWER GOOD/FAIL REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SP-750-5 5V 120A 0 ~ 120A 600W 4.75 ~ 5.5V 2.0% 0.5% 2.0% 16ms/230VAC 90 ~ 264VAC 47 ~ 63Hz PF>0.96/230VAC 80% 8.8A/115VAC 27A/115VAC 0.99/115VAC at full load 85% 4.2A/230VAC 45A/230VAC 87% 89% 89% 90% SP-750-12 12V 62.5A 0 ~ 62.5A 750W 120mVp-p 10 ~ 13.5V 1.0% 0.3% 0.5% 16ms/115VAC at full load 127 ~ 370VDC SP-750-15 15V 50A 0 ~ 50A 750W 120mVp-p 13.5 ~ 16.5V 1.0% 0.3% 0.5% 1500ms, 50ms/115VAC at full load SP-750-24 24V 31.3A 0 ~ 31.3A 751.2W 120mVp-p 22 ~ 26.4V 1.0% 0.2% 0.5% SP-750-27 27V 27.8A 0 ~ 27.8A 750.6W 120mVp-p 24 ~ 30V 1.0% 0.2% 0.5% SP-750-48 48V 15.7A 0 ~ 15.7A 753.6W 120mVp-p 43 ~ 56V 1.0% 0.2% 0.5% RIPPLE & NOISE (max.) Note.2 120mVp-p 1500ms, 50ms/230VAC 31 ~ 36.5V 57.6 ~ 67.2V (TSW2 ) detect on heatsink of power diode Protection type : Shut down o/p voltage, recovers automatically after temperature goes down 50ms/1ms Note.5 RC+/RC- short power on, open power off -20 ~ +60 (Refer to output load derating curve) 20~90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.05%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B (Note 4) HARMONIC CURRENT EMS IMMUNITY MTBF Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A 124K hrs min. MIL-HDBK-217F (25 278*127*63.5mm (L*W*H) 2.9Kg; 6pcs / 18.4Kg / 0.98CUFT ) OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. The power supply unit will have no output if the shorting connector is not assembled between RC+ & RC-. File Name:SP-750-SPEC 2010-10-18 750W Single Output Power Supply Mechanical Specification 220 16 SP-750 Case No.919A 113 series Unit:mm 7 30 20 4-M3 5 6-M3 L=6 4-M3 Air flow direction O/P 1 1 2 3 7 240 251 278 127 7 10 39 I/P 113 149 33 5 6 7 8 1 2 3 4 +V ADJ. 40.5 2 72 5 CONTROL 24.5 19 max. 4-M3 20 max. 34.5 20 63.5 91 11 2-M6 BOTTOM VIEW 28 max. 220 TOP VIEW 15 AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Assignment AC/L AC/N FG DC Output Terminal Pin No. Assignment Pin No. 1 2 Assignment DC OUTPUT +V DC OUTPUT -V Control Pin No. Assignment : MOLEX 5559-NP uses 5558male crimp terminal Pin No. 1 2 3 4 Assignment NC -S G RCPin No. Assignment Mating connector Terminal NC 5 MOLEX 5556 6 PF(Power fail signal) MOLEX 5557-NR Female crimp Terminal +S 7 receptacle RC+ 8 Block Diagram PFC fosc : 100KHz PWM fosc : 140KHz +S I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING RECTIFIERS PFC POWER SWITCHING DETECTION CIRCUIT PWM POWER SWITCHING RECTIFIERS & FILTER O.T.P. CURRENT LIMIT +V -V -S O.L.P. DETECTION CIRCUIT O.V.P. PFC CONTROL PWM CONTROL PF O.T.P. REMOTE CONTROL AUX POWER RC FAN FAN LOCK PROTECTION File Name:SP-750-SPEC 2010-10-18 750W Single Output Power Supply Derating Curve Static Characteristics SP-750 series 100 100 90 80 85 70 60 LOAD (%) LOAD (%) 0 10 20 30 40 50 60 70 (HORIZONTAL) 40 60 50 40 20 -20 90 95 100 115 260 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz Control Terminal Instruction Manual Power Fail Signal PF Signal is the voltage difference between "G" and "PF" pin output G PF Remote Sensing RC+ +S PF NC RC- G -S NC RC+ +S PF NC RC- G -S NC -V +V -V +V LOAD + -S LOAD + Remote Control Power ON: RC+/RC- Short Power OFF: RC+/RC- open RC- RC+ +S RC+ +S PF NC RC- G -S NC -V +V LOAD + F ile Name:SP-750-SPEC 2010-10-18