6A8G

AXIAL SILASTIC GUARD JUNCTION STANDARD RECTIFIER 6A05G THRU 6A10G FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 6.0 Ampere Glass passivated chip junction Low reverse leakage Low forward voltage High forward surge current capability High temperature soldering guaranteed 260℃/10 seconds,0.375”(9.5mm)lead length R-6 1.0(25.4) MIN. .052(1.3) .048(1.2) DIA. .360(9.1) .340(8.6) MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.07ounce, 2.0 gram .360(9.1) DIA. .340(8.6) 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% 6A 6A SYMBOLS 05G 1G Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current 0.375”(9.5mm) lead length at T A=60℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A Maximum DC Reverse Current at rated DC blocking Voltage at T A = 25℃ TA = 100℃ 6A 2GG 200 140 200 6A 4G 400 280 400 6.0 250 0.95 10.0 500 500 100 10 (-55 to +150) (-55 to +150) 6A 6G 600 420 600 6A 8G 800 560 800 6A 10G 1000 700 1000 UNIT Volts Volts Volts Amps Amps Volts µA µA pF ℃/W ℃ ℃ I(AV) IFSM VF IR IR(AV) CJ RθJA TJ TSTG Maximum Full Load Reverse Current, full cycle Average 0.375(9.5mm) lead length at TL=105℃ Typical Junction Capacitance (NOTE 2) Typical Thermal Resistance (NOTE 1) Operating Temperature Range Storage Temperature Range Notes: 1. Thermal Resistance from Junction to Ambient with 0.375”(9.5mm) lead length, PCB. mounted with 1.1”×1.1” (30mm×30mm) copper pads. 2. Measured at 1.0 MHz and applied reverse voltage of 4.0V E-mail: sales@cnmic.com Web Site: www.cnmic.com AXIAL SILASTIC GUARD JUNCTION STANDARD RECTIFIER 6A05G THRU 6A10G VOLTAGE RANGE CURRENT 50 to 1000 Volts 6.0 Ampere RATING AND CHRACTERISTIC CURVES 6A05S THRU 6A10S FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 6.0 400 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT AVERAGE FORWARD CURRENT, 5.0 PEAK FORWARD SURGE CURRENT, (A) 4.0 (A) 3.0 60 Hz Resistive or inductive Loads Ground Plane 1”×1”Copper Surface Area P.C.Board Recommended P.C. Board Mounting 300 250 200 8.3ms Single Half Sine-Wave (JEDEC Method) T= Tjmax 2.0 100 1.0 0 0 25 50 60 75 100 125 150 175 1 1 Cycle 2 4 6 8 10 20 40 60 80 100 AMBIENT TEMPERATURE, ( ° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 INSTANTANEOUS REVERSE CURRENT, (μA) 10 INSTANTANEOUS FORWARD CURRENT, 100 TJ=100° C 1.0 (A) 10 0.1 TJ =25° C TJ =25° C Pulse Width=300us 1% Duty Cycle 1.0 0.01 0 20 40 60 80 100 120 140 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.6-TYPICAL THERMAL RESISTANCE VS LEAD LENGTH 70 FIG.5-TYPICAL JUNCTION CAPACITANCE 1000 JUNCTION CAPACITANCE,(pF) 60 THERMAL RESISTANCE, (° C/W) 50 100 40 30 Single Lead to heat Sink, Insignificant Heat Flow Through Other Lead TJ =25° C f=1MHz Vsig=50mVp-p R θJL 20 10 10 0.1 1.0 10 100 0 0 0.2 0.4 Both Leads to Heat Sink, Equal Length 0.6 0.8 1.0 REVERSE VOLTAGE,(V) EQUAL LEAD LENGTH TO HEAT SINK(IN.) E-mail: sales@cnmic.com Web Site: www.cnmic.com