FR105G

FAST RECOVERY GLASS PASSIVATED RECTIFIER FR101G THRU FR107G FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 1.0 Ampere DO-41 Fast switching for high efficiency Glass passivated chip junction High current surge capability Low leakage High temperature soldering guaranteed 260℃/10 seconds,0.375”(9.5mm)lead length at 5 lbs (2.3kg) tension MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.012ounce, 0.33 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS FR101G FR102G Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current 0.375″(9.5mm) lead length at T A =55℃ Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage TA = 125℃ Maximum Reverse Recovery Time(NOTE 3) Typical Junction Capacitance (NOTE 1) Typical Thermal Resistance (NOTE 2) Operating Temperature Range Storage Temperature Range FR103G 200 140 200 FR104G 400 280 400 1.0 30 1.3 5.0 100 FR105G 600 420 600 FR106G 800 560 800 FR107G 1000 700 1000 UNIT Volts Volts Volts Amp Amps Volts µA I(AV) IFSM VF IR trr CJ RθJA TJ TSTG 150 250 15 50 (-55 to +150) (-55 to +150) 500 nS pF ℃/W ℃ ℃ Notes: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2. Thermal Resistance from Junction to Ambient at.375″(9.5mm) lead length, P.C board mounted. 3. Test conditions: IF=0.5A, IR=1.0A, IRR=0.25A. E-mail: sales@cnmic.com Web Site: www.cnmic.com FAST RECOVERY GLASS PASSIVATED RECTIFIER FR101G THRU FR107G VOLTAGE RANGE CURRENT 50 to 1000 Volts 1.0 Ampere RATING AND CHRACTERISTIC CURVES FR101G THRU FR107G FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, 1.2 Single Phase FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE 1.0 30 CURRENT, (A) 0.8 Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 8.3ms Single Half Sine-Wave (JEDEC Method) T= Tjmax 20 (A) 0.6 0.4 10 0.2 0 0 25 50 55 75 100 125 150 175 0 1 1 Cycle 40 60 100 2 4 6 8 10 20 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, INSTANTANEOUS REVERSE CURRENT, 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 10 TJ =125° C 1.0 (A) (μA) 1.0 0.1 TJ =75° C TJ =25 ° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.1 TJ =25 ° C 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE,(V) 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK FIG.5-TYPICAL JUNCTION CAPACITANCE 100 REVERSE VOLTAGE,(%) JUNCTION CAPACITANCE,(pF) F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE (-) 10 (+) 25 Vdc (approx.) (-) TJ =25° C f=1MHz Vsig=50mVp-p D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) +0.5A 0 -0.25A 1Ω NON INDUCTIVE -1.0A 1cm 1 0.1 1.0 10 100 REVERSE VOLTAGE,(V) NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm E-mail: sales@cnmic.com Web Site: www.cnmic.com