TC1306_07

Obsolete Device TC1306 Dual 150mA CMOS LDO With Select Mode™ Operation, Shutdown and RESET Output Features • Extremely Low Supply Current for Longer Battery Life • Select Mode™ Operation: Selectable Output Voltages for High Design Flexibility • Very Low Dropout Voltage • 10μsec (Typ.) Wake-Up Time from SHDN • Maximum 150mA Output Current per Output • High Output Voltage Accuracy • Power-Saving Shutdown Mode • RESET Output Can Be Used as a Low Battery Detector or Processor Reset Generator • Over Current Protection and Over Temperature Shutdown • Space Saving 8-Pin MSOP Package General Description The TC1306 combines two CMOS Low Dropout Regulators and a Microprocessor Monitor in a space saving 8-Pin MSOP package. Designed specifically for battery operated systems, total supply current is typically 120μA at full load, 20 to 60 times lower than in bipolar regulators. The TC1306 features selectable output voltages for higher design flexibility. The dual-state SELECT input pin allows the user to select VOUT2 from 2 different values (2.8V and 3.0V). VOUT1 supplies a fixed 1.8V voltage. An active low RESET is asserted when the output voltage VOUT2 falls below the 2.63V reset voltage threshold. The RESET output remains low for 300msec (typical) after VOUT2 rises above reset threshold. When the shutdown control (SHDN1) is low, the regulator output voltage VOUT1 falls to zero and RESET output remains valid. When the shutdown control (SHDN2) is low, the regulator output voltage VOUT2 falls to zero and RESET output is low. Other key features for the device include ultra low noise operation, fast response to step changes in load and very low dropout voltage (typically 125mV at full load). The device also incorporates both over temperature and over current protection. Each regulator is stable with an output capacitor of only 1μF and has a maximum output current of 150mA. Applications • • • • • • • Load Partitioning Battery Operated Systems Portable Computers Medical Instruments Instrumentation Pagers and Cellular/GSM/PHS Phones Linear Post-Regulator for SMPS Device Selection Table Part Number TC1306R-BDVUA Package Junction Temperature Range Typical Application VIN GND 3 SELECT SHDN1 4 1 2 8 7 RESET VOUT2 VOUT1 3.3µF 5 SHDN2 8-Pin MSOP -40°C to +125°C NOTE: “R” denotes the suffix for the 2.63V RESET threshold. “B” indicates VOUT1 = 1.8V (fixed). “D” indicates VOUT2 = 2.8V, 3.0V (selectable). Other output voltages are available. Please contact Microchip Technology Inc. for details. TC1306 6 3.3µF Package Type 8-Pin MSOP VIN 1 GND 2 SELECT 3 SHDN1 4 8 RESET 7 VOUT2 TC1306 6 VOUT1 5 SHDN2 © 2007 Microchip Technology Inc. DS21527C-page 1 TC1306 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. ABSOLUTE MAXIMUM RATINGS* Input Voltage .........................................................6.5V Output Voltage........................... (-0.3V) to (VIN + 0.3V) Power Dissipation................Internally Limited (Note 7) Maximum Voltage on Any Pin ......... VIN +0.3V to -0.3V Operating Temperature Range.... -40°C < TJ < +125°C Storage Temperature Range ..............-65°C to +150°C TC1306 ELECTRICAL SPECIFICATIONS Electrical Characteristics: VIN = VR + 1V, IL = 100μA, CL = 3.3μF, SHDN1 > VIH, SHDN2 > VIH, TA = 25°C, unless otherwise noted. Boldface type specifications apply for junction temperature of -40°C to +125°C. Applies to both VOUT1 and VOUT2. Symbol VIN IOUTMAX VOUT TCVOUT ΔVOUT/ΔVIN Parameter Input Operating Voltage Maximum Output Current Output Voltage (VOUT1 and VOUT2) VOUT Temperature Coefficient Line Regulation Min 2.7 150 VR – 2.5% — — — — — Typ — — 20 40 0.05 0.3 2 45 85 125 120 0.05 55 450 0.04 10 Max 6.0 — — — 0.35 2 — 120 240 360 200 0.5 — — — — Units V mA V Note 1 Per Channel Note 2 Test Conditions VR ± 0.5% VR + 2.5% ppm/°C Note 3 % % mV (VR + 1V) < VIN < 6V IL = 0.1mA to IOUTMAX (Note 4) IL = 100μA IL = 50mA IL = 100mA IL = 150mA, (Note 5) SHDN1, SHDN2 = VIH, IL = 0 SHDN1, SHDN2 = 0V FRE ≤ 120Hz VOUT = 0V Notes 6, 7 VIN = 5V CIN = 1μF, COUT = 4.7μF IL = 30mA, (See Figure 4-1) VIN = 5V CIN = 1μF, COUT = 4.7μF IL = 30mA, (See Figure 4-1) ΔVOUT/VOUT Load Regulation VIN – VOUT Dropout Voltage IIN IINSD PSRR IOUTSC ΔVOUTΔPD tWK Supply Current Shutdown Supply Current Power Supply Rejection Ratio Output Short Circuit Current Thermal Regulation Wake Up Time (from Shutdown Mode) — — — — — — μA μA dB mA V/W μsec ts Settling Time (from Shutdown Mode) — 40 — μsec Note 1: 2: 3: 4: 5: 6: 7: The minimum VIN has to meet two conditions: VIN ≥ 2.7 and VIN = VR + VDROPOUT. VR is the regulator output voltage setting. For example: VR = 2.8V, 3.0V. TC VOUT = (VOUTMAX – VOUTMIN) x 106 VOUT x ΔT Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested over a load range from 0.1mA to the maximum specified output current. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a 1V differential. Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 msec. The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 Thermal Considerations section of this data sheet for more details. DS21527C-page 2 © 2007 Microchip Technology Inc. TC1306 TC1306 ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: VIN = VR + 1V, IL = 100μA, CL = 3.3μF, SHDN1 > VIH, SHDN2 > VIH, TA = 25°C, unless otherwise noted. Boldface type specifications apply for junction temperature of -40°C to +125°C. Applies to both VOUT1 and VOUT2. Symbol TSD ΔTSD eN SHDN Input VIH VIL VSELH VSELL VINMIN VTH SHDN Input High Threshold SHDN Input Low Threshold SELECT Input HIgh Threshold SELECT Input Low Threshold Minimum VIN Operating Voltage Reset Threshold Reset Threshold Tempco VOUT2 to Reset Delay Reset Active Time-out Period VOL RESET Output Voltage Low 65 — 65 — 1.0 1.2 2.59 2.55 — — 140 — — — 0.8 VOUT2 VOUT2 – 1.5 Note 1: 2: 3: 4: 5: 6: 7: Parameter Thermal Shutdown Die Temperature Thermal Shutdown Hysteresis Output Noise Min — — — Typ 160 15 200 — — — — — — 2.63 — 30 100 300 — — — — — Max — — — — 15 — 15 6.0 6.0 2.66 2.70 — — 560 0.3 0.4 0.3 — — Units °C °C nV√Hz %VIN %VIN %VIN %VIN V V ppm/°C μsec msec V Test Conditions F = 10kHz VIN = 2.7V to 6.0V VIN = 2.7V to 6.0V VIN = 2.7V to 6.0V VIN = 2.7V to 6.0V TA = 0°C to +70°C TA = -40°C to +125°C TA = +25°C TA = -40°C to +125°C VOUT2 = VTH to (VTH – 100mV) VOUT2 = VTHMIN, ISINK = 1.2mA VOUT2 = VTHMIN, ISINK = 3.2mA VOUT2 > 1.0V, ISINK = 50μA VOUT2 > VTHMAX, ISOURCE = 500μA VOUT2 > VTHMAX, ISOURCE = 800μA SELECT Input RESET Output VOH RESET Output Voltage High V The minimum VIN has to meet two conditions: VIN ≥ 2.7 and VIN = VR + VDROPOUT. VR is the regulator output voltage setting. For example: VR = 2.8V, 3.0V. TC VOUT = (VOUTMAX – VOUTMIN) x 106 VOUT x ΔT Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested over a load range from 0.1mA to the maximum specified output current. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a 1V differential. Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 msec. The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 Thermal Considerations section of this data sheet for more details. © 2007 Microchip Technology Inc. DS21527C-page 3 TC1306 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: Pin No. (8-Pin MSOP) 1 2 3 4 PIN FUNCTION TABLE Symbol VIN GND SELECT SHDN1 Power supply input. Ground terminal. SELECT control for setting VOUT2. SELECT = Low for VOUT2 = 2.8V, SELECT = High for VOUT2 = 3.0V. Shutdown control input for VOUT1. Regulator 1 is fully enabled when a logic high is applied to this input. Regulator 1 enters shutdown when a logic low is applied to this input. During shutdown, regulator output voltage falls to zero, RESET output remains valid. Shutdown control input for VOUT2. Regulator 2 is fully enabled when a logic high is applied to this input. Regulator 2 enters shutdown when a logic low is applied to this input. During shutdown, regulator output voltage falls to zero, RESET output is low. Regulated voltage output 1. Regulated voltage output 2. RESET Output. RESET = Low when VOUT2 is below the Reset Threshold Voltage. RESET = High when VOUT2 is above the Reset Threshold Voltage. Description 5 SHDN2 6 7 8 VOUT1 VOUT2 RESET 3.0 DETAILED DESCRIPTION The TC1306 is a precision fixed output voltage regulator that contains two fully independent 150mA outputs. The device also features separate shutdown modes for low-power operation. The Select Mode™ operation allows the user to select VOUT2 from two different values (2.8V, 3.0V), therefore providing high design flexibility. VOUT1 supplies a fixed 1.8V output voltage. The CMOS construction of the TC1306 results in a very low supply current, which does not increase with load changes. In addition, VOUT remains stable and within regulation at no load currents. The TC1306 also features an integrated microprocessor supervisor that monitors the VOUT2 output. The active low RESET signal is asserted when the voltage of VOUT2 falls below the reset voltage threshold (2.63V). The RESET output remains low for 300msec (typical) after VOUT2 rises above the reset threshold. The RESET output of the TC1306 is optimized to reject fast transient glitches on the monitored output line. DS21527C-page 4 © 2007 Microchip Technology Inc. TC1306 4.0 4.1 TYPICAL APPLICATIONS Input and Output Capacitor 4.3 Select Mode™ Operation The TC1306 is stable with a wide range of capacitor values and types. A capacitor with a minimum value of 1μF from VOUT to Ground is required. The output capacitor should have an effective series resistance (ESR) of 0.1Ω to 10Ω for a 1μF capacitor and 0.01Ω to 10Ω for a 10μF capacitor. A 1μF capacitor should be connected from the VIN to GND if there is more than 10 inches of wire between the regulator and the AC filter capacitor, or if a battery is used as the power source. Aluminum electrolytic or tantalum capacitor types can be used. (Since many aluminum electrolytic capacitors freeze at approximately -30°C, solid tantalums are recommended for applications operating below -20°C). When operating from sources other than batteries, supply-noise rejection and transient response can be improved by increasing the value of the input and output capacitors and employing passive filtering techniques. The Select Mode™ operation is a dual-state input that allows the user to select VOUT2 from two different values. By applying a logic low to the SELECT pin, VOUT2 is set to supply a 2.8V output voltage. A logic high signal at the SELECT pin sets VOUT2 to 3.0V. This output voltage functionality provides high design flexibility and minimizes cost associated with inventory, time-to-market and new device qualifications. 4.4 Turn On Response The turn on response is defined as two separate response categories, Wake Up Time (tWK) and Settling Time (tS). The TC1306 has a fast Wake Up Time (10μsec typical) when released from shutdown. See Figure 4-1 for the Wake Up Time designated as tWK. The Wake Up Time is defined as the time it takes for the output to rise to 2% of the VOUT value after being released from shutdown. The total turn on response is defined as the Settling Time (tS), see Figure 4-1. Settling Time (inclusive with tWK) is defined as the condition when the output is within 2% of its fully enabled value (40μsec typical) when released from shutdown. The settling time of the output voltage is dependent on load conditions, output voltage and VOUT (RC response). 4.2 Shutdown Mode Applying a logic high to each of the shutdown pins turns on the corresponding output. Each regulator enters shutdown mode when a logic low is applied to the corresponding input. During shutdown mode, output voltage falls to zero, and regulator supply current is reduced to 0.5μA (max). If shutdown mode is not necessary, the pins should be connected to VIN. FIGURE 4-1: WAKE-UP RESPONSE TIME VIH VIL 98% tS SHDN VOUT 2% tWK © 2007 Microchip Technology Inc. DS21527C-page 5 TC1306 5.0 5.1 THERMAL CONSIDERATIONS Thermal Shutdown Equation 5-1 can be used in conjunction with Equation 5-2 to ensure regulator thermal operation is within limits. For example: Given: VINMAX VOUT1MIN = 3.8V ± 5% = 1.8V ± 2.5% Integrated thermal protection circuitry shuts the regulator off when die exceeds approximately 160°C. The regulator remains off until the die temperature drops to approximately 145°C. Thermal shutdown is intended to protect the device under transient accidental (fault) overload conditions. Thermal Shutdown may not protect the LDO while operating above junction temperatures of 125°C continuously. Sufficient thermal evaluation of the design needs to be conducted to ensure that the junction temperature does not exceed 125°C. VOUT2MIN = 3.0V ± 2.5% ILOAD1MAX = 60mA ILOAD2MAX = 120mA TJMAX TAMAX θJA = 125°C = 55°C = 200°C/W 5.2 Power Dissipation Find: 1. Actual power dissipation 2. Maximum allowable dissipation Actual power dissipation: PD ≈ [(VINMAX – VOUT1MIN)] x ILOAD1MAX + [(VINMAX – VOUT2MIN)] x ILOAD2MAX [(3.8 x 1.05) – (1.8 x .975)] x 60 x 10-3 + [(3.8 x 1.05) – (3.0 x .975)] x 120 x 10-3 = 256mW Maximum allowable power dissipation: PD = (TJMAX – TAMAX) θJA = (125 – 55) 200 = 350mW In this example, the TC1306 dissipates a maximum of 262mW; below the allowable limit of 350mW. In a similar manner, Equation 5-1 and Equation 5-2 can be used to calculate maximum current and/or input voltage limits. For example, the maximum allowable VIN is found by substituting the maximum allowable power dissipation of 350mW into Equation 5-1, from which VINMAX = 4.5V. The amount of power the regulator dissipates is primarily a function of input and output voltage, and output current. The following equation is used to calculate worst case actual power dissipation. EQUATION 5-1: PD ≈ (VINMAX – VOUT1MIN)ILOAD1MAX + (VINMAX – VOUT2MIN)ILOAD2MAX Where: PD = Worst case actual power dissipation VINMAX = Maximum voltage on VIN VOUT1MIN = Minimum regulator output voltage1 ILOAD1MAX = Maximum output (load) current1 VOUT2MIN = Minimum regulator output voltage2 ILOAD2MAX = Maximum output (load) current2 The maximum allowable power dissipation (Equation 5-2) is a function of the maximum ambient temperature (TAMAX), the maximum allowable die temperature (125°C), and the thermal resistance from junction-to-air (θJA). The MSOP-8 package has a θJA of approximately 200°C/W when mounted on a four layer FR4 dielectric copper clad PC board. 5.3 Layout Considerations EQUATION 5-2: PDMAX = (TJMAX – TAMAX) θJA Where all terms are previously defined. The primary path of heat conduction out of the package is via the package leads. Therefore, layouts having a ground plane, wide traces at the pads, and wide power supply bus lines combine to lower θJA and therefore increase the maximum allowable power dissipation limit. DS21527C-page 6 © 2007 Microchip Technology Inc. TC1306 6.0 Note: TYPICAL CHARACTERISTICS The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. VOUT1 at Various VDD and Load vs. Temperature 1.81 1.80 1.79 VOUT2 (V) VOUT (V) 1.78 VDD = 2.8V, IL = 150mA Load 1.77 1.76 1.75 1.74 -40 -20 5 30 55 80 105 125 VDD = 6.0V, IL = 100mA Load VDD = 6.0V, IL = 100µA Load VOUT2 at Various VDD / Load Current vs. Temperature (Select = GND) 2.505 2.500 2.495 VOUT2 (V) 2.490 2.485 2.480 2.475 2.470 2.465 2.460 -40 VDD = 3.8V, IL = 150mA VDD = 3.8V, IL = 100mA VDD = 3.8V, IL = 50mA VDD = 3.8V, IL = 100µA -20 5 30 55 80 105 125 VDD = 6.0V, IL = 100µA VOUT2 at Various VDD / Load Current vs. Temperature (Select = VDD) 3.000 2.995 2.990 2.985 2.980 2.975 2.970 2.965 2.960 2.955 2.950 -40 VDD = 3.8V, IL = 50mA VDD = 3.8V, IL = 100mA VDD = 4.0V, IL = 150mA -20 5 30 55 80 105 125 VDD = 4.0V, IL = 100µA VDD = 6.0V, IL = 100µA TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C) IDD vs. VDD (Select = GND) 160 140 120 IDD (µA) 100 80 60 40 20 0 3 3.5 4 4.5 5 VDD (V) 5.5 6 125°C Load Regulation 1 vs. Temperature 0.50 0.50 0.45 0.40 LOAD REG (%) 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.45 0.40 LOAD REG (%) 0.35 0.30 0.25 0.20 0.15 0.10 0.05 % Load Reg #1, IL = 0.1 to 150mA 0.00 -40 -20 5 30 55 80 105 125 TEMPERATURE (°C) Load Regulation 2 vs. Temperature (Select = GND) 25°C -40°C IL = 0.1 to 150mA 0.00 -40 -20 5 30 55 80 105 125 TEMPERATURE (°C) Load Regulation 2 vs. Temperature (Select = VDD) 0.50 DROPOUT VOLTAGE (V) LOAD REGULATION (%) 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 -40 -20 5 30 55 80 105 125 TEMPERATURE (°C) IL = 0.1 to 150mA Dropout Voltage vs. Load Current (Select = GND) 0.20 DROPOUT VOLTAGE (V) 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 0 25 50 75 100 125 150 LOAD CURRENT (mA) 125°C Dropout Voltage vs. Load Current (Select = VDD) 0.20 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 0 25 50 75 100 125 150 LOAD CURRENT (mA) 125°C 25°C -40°C 25°C -40°C © 2007 Microchip Technology Inc. DS21527C-page 7 TC1306 6.0 TYPICAL CHARACTERISTICS (CONTINUED) Power Supply Rejection Ratio vs. Frequency 0 VINDC = 4V VINAC = 100mVP-P VOUTDC = 3V IOUT = 150mA COUT = 10µF Ceramic Power Supply Rejection Ratio vs. Frequency 0 VINDC = 4V VINAC = 100mVP-P VOUTDC = 3V IOUT = 100µA COUT = 10µF Tantalum -20 -20 PSRR (dB) PSRR (dB) 10 100 1k f (Hz) 10k 100 1M -40 -40 -60 -60 -80 -80 -100 -100 10 100 1k f (Hz) 10k 100 1M Power Supply Rejection Ratio vs. Frequency 0 VINDC = 4V VINAC = 100mVP-P VOUTDC = 3V IOUT = 150mA COUT = 10µF Tantalum Output Noise 10 -20 1 Noise (μV/√HZ) VOUT1 VOUT2 0.1 PSRR (dB) -40 -60 -80 0.01 COUT1 = COUT2 = 4.7mF, ILOAD = 100mA, VIN = 4.0V VOUT1 = VOUT2 = 3.0V 0.1 1 f (Hz) 10 100 1000 -100 10 100 1k f (Hz) 10k 100 1M 0.001 0.01 DS21527C-page 8 © 2007 Microchip Technology Inc. TC1306 6.0 TYPICAL CHARACTERISTICS (CONTINUED) Shutdown Response Thermal Shutdown Response Output Voltage (1V / div) VOUT SHDN (5V / div) VIN = 4.0V VOUT = 3.0V COUT = 10μF ILOAD = 100μA VIN = 6.0V VOUT = 1.8V CIN = 1μF COUT = 1μF Time (200ms / div) Time (500ms / div) Thermal Shutdown Response Thermal Shutdown Response VOUT VOUT VIN = 6.0V VOUT = 2.8V CIN = 1μF COUT = 1μF VIN = 6.0V VOUT = 3.0V CIN = 1μF COUT = 1μF Time (500ms / div) Time (500ms / div) Output Voltage Output Voltage (50mV / div) (50mV / div) Line Transient Response VOUT2 Output Voltage Output Voltage (50mV / div) (50mV / div) Line Transient Response VOUT2 VOUT1 VOUT1 Input Voltage (2V / div) VIN 3.6V 4.6V Input Voltage (2V / div) COUT1 = COUT2 = 1μF Tantalum RLOAD = 30kΩ VIN 3.6V COUT1 = COUT2 = 10μF Ceramic RLOAD = 30kΩ 4.6V Time (500ms / div) Time (500ms / div) © 2007 Microchip Technology Inc. DS21527C-page 9 TC1306 6.0 TYPICAL CHARACTERISTICS (CONTINUED) Load Transient Response VOUT2 Output Voltage Output Voltage (20mV / div) (20mV / div) Output Voltage Output Voltage (20mV / div) (20mV / div) Thermal Shutdown Response VOUT2 VOUT1 VOUT1 Output Current Output Current COUT1 = COUT2 = 10μF Ceramic VIN = 5.5V RLOAD = 30kΩ RL = 30Ω COUT1 = COUT2 = 1μF Tantalum VIN = 5.5V RLOAD = 30kΩ RL = 30Ω 100mA 100mA 100μA 100μA Time (500ms / div) Time (500ms / div) Output Voltage 1 Output Voltage 2 (20mV / div) (50mV / div) Output Voltage 1 Output Voltage 2 (20mV / div) (50mV / div) Load Transient Response VOUT2 Thermal Shutdown Response VOUT2 VOUT1 VOUT1 Output Current Output Current COUT1 = COUT2 = 10μF Ceramic VIN = 5.5V RLOAD = 30kΩ RL = 30Ω COUT1 = COUT2 = 1μF Tantalum VIN = 5.5V RLOAD = 30kΩ RL = 30Ω 100mA 100mA 100μA 100μA Time (500ms / div) Time (500ms / div) Wake-Up Response Output Voltage 2 (1V / div) 3.0V VOUT2 VOUT1 Output Voltage 1 (1V / div) 1.8V /Shdn1 = /Shdn2 COUT1 = COUT2 = 1μF Tantalum VIN = 5.5V RLOAD = 30kΩ Time (20ms / div) DS21527C-page 10 © 2007 Microchip Technology Inc. TC1306 7.0 7.1 7.2 PACKAGING INFORMATION Package Marking Information Taping Form Component Taping Orientation for 8-Pin MSOP Devices Package marking data not available at this time. User Direction of Feed PIN 1 W P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 8-Pin MSOP 12 mm 8 mm 2500 13 in 7.3 Package Dimensions 8-Pin MSOP PIN 1 .122 (3.10) .114 (2.90) .197 (5.00) .189 (4.80) .026 (0.65) TYP. .122 (3.10) .114 (2.90) .043 (1.10) MAX. .016 (0.40) .010 (0.25) .006 (0.15) .002 (0.05) 6° MAX. .028 (0.70) .016 (0.40) .008 (0.20) .005 (0.13) Dimensions: inches (mm) © 2007 Microchip Technology Inc. DS21527C-page 11 TC1306 NOTES: DS21527C-page 12 © 2007 Microchip Technology Inc. TC1306 APPENDIX A: REVISION HISTORY Revision C (February 2007) • Changed device status to “Obsolete” on data sheet • Corrected Figure 6-4 Output Noise Revision B (May 2002) • Undocumented changes Revision A (March 2001) • Original Release of this Document. © 2007 Microchip Technology Inc. DS21527C-page 13 TC1306 NOTES: DS21527C-page 14 © 2007 Microchip Technology Inc. TC1306 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. © 2007 Microchip Technology Inc. DS21527C-page15 TC1306 NOTES: DS21527C-page16 © 2007 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • • • Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” • • Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Linear Active Thermistor, Migratable Memory, MXDEV, MXLAB, PS logo, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2007, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona, Gresham, Oregon and Mountain View, California. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2007 Microchip Technology Inc. DS21527C-page 17 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Habour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 ASIA/PACIFIC India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 12/08/06 DS21527C-page 18 © 2007 Microchip Technology Inc.