GxxooXS-2W

H-XS-2W&G-XS-2W Serie FIXED INPUT,ISOLATED&UNREGULATED Single∕Dual Output DC∕DC Converter SELECTION GUIDE Input Output Efficiency (%,Typ) Nominal Range Max Min G0505XS-2W 5 4.5-5.5 ±5 ±200 ±20 74 84 G0509XS-2W 5 4.5-5.5 ±9 ±111 ±12 77 81 G0512XS-2W 5 4.5-5.5 ±12 ±83 ±9 77 82 G0515XS-2W 5 4.5-5.5 ±15 ±67 ±7 77 83 H0505XS-2W 5 4.5-5.5 5 400 40 74 180 H0509XS-2W 5 4.5-5.5 9 222 23 77 150 H0512XS-2W 5 4.5-5.5 12 167 17 77 84 H0515XS-2W 5 4.5-5.5 15 133 14 77 83 G1205XS-2W 12 10.8-13. ±5 ±200 ±20 75 82 G1209XS-2W 12 10.8-13. ±9 ±111 ±12 78 83 G1212XS-2W 12 10.8-13. ±12 ±83 ±9 80 180 G1215XS-2W 12 10.8-13. ±15 ±67 ±7 78 150 H1205XS-2W 12 10.8-13. 5 400 40 75 80 H1209XS-2W 12 10.8-13. 9 222 23 78 85 H1212XS-2W 12 10.8-13. 12 167 17 80 87 H1215XS-2W 12 10.8-13. 15 133 14 78 84 Industry standard pinout G2405XS-2W 24 21.6-26. ±5 ±200 ±20 75 180 G2409XS-2W 24 21.6-26. ±9 ±111 ±12 77 150 Power sharing on output G2412XS-2W 24 21.6-26. ±12 ±83 ±9 80 82 G2415XS-2W 24 21.6-26. ±15 ±67 ±7 79 80 H2405XS-2W 24 21.6-26. 5 400 40 75 78 H2409XS-2W 24 21.6-26. 9 222 23 77 80 H2412XS-2W 24 21.6-26. 12 167 17 80 180 H2415XS-2W 24 21.6-26. 15 133 14 74 150 FEATURES RoHS compliant ◆ Efficiency up to 80% ◆ SIP Package ◆ Wide temperature performance at full ◆ 2 Watt load,-40°C to 85 °C UL 94V-0 package material ◆ No heatsink required ◆ LOW Isolation Capacitance ◆ ◆ ◆ 6KVDC isolation ◆ Continuous Short Circuit Protection ◆ Internal SMD construction ◆ Voltage(VDC) Current Switching Frequency (KHz,Typ) Voltage (VDC) Order code No external components required ◆ Good dynamic feature ◆ ISOLATION SPECIFICATIONS Parameter ① ② ③ ④ ⑤ H 05 05 X S -2W ①Product Series ③Output Voltage ⑤SIP Package ②Input Voltage ④Fixed Input ⑥Rated Power Min. Flash tested for 1 minute and 1mA 6000 Isolation resistance ⑥ Test conditions Isolation test voltage MODEL SELECTION Test at Viso=500VDC(Vin/Vout) The H_XS-2W&G_XS-2W series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) where the voltage of the input power supply is fixed (voltage variation ≤±10%); 2) where isolation is necessary between input and output (isolation voltage ≤6000VDC); 3) where the regulation of the output voltage and the output ripple noise are not demanded. Such as: purely digital circuits,ordinary low frequency analog circuits,and 1GBT power device driving circuits. 1000 Unit MΩ 10 Output power Line regulation Max VDC Isolation capacitance OUTPUT SPECIFICATIONS Parameter Test conditions APPLICATIONS Typ. Min Typ. PF Max Unit 2 W 0.2 For Vin change of ±1% ±1.2 10% to 100% full load(5V output) 10 15 10% to 100% full load(9V output) 8.3 15 10% to 100% full load(12V output) 6.8 15 6.3 15 % Load regulation 10% to 100% full load(15V output) Output voltage accuracy See tolerance envelope graph Temperature drift 100% full load Output Ripple&Noise 20MHz Bandwidth ±0.03 150 (5V input) MV p-p 45 (12V/24v input) Switching frequency %/°C 250 50 Khz Full load,nominal input * Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: Dual output models unbalanced load: ±5%. MICRODC RESERVES THE COPYRIGHT http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 Page 1 of 2 H-XS-2W&G-XS-2W Serie COMMON SPECIFICATIONS Parameter Conditions Min. Typ. Operating temperature % -40 85 -55 Storage temperature Lead temperature Units 95 Storage humidity range Max. 125 Filtering To get the input/output ripple,an "LC"filtering network may be connected to the input and output ends of the DC/DC converter.Which may produce a more significant filtering effect.It should also be noted that the inductance and the frequency of the "LC"filtering network should be staggered with the DC/DC frequency to avoid mutual interference see (Figure 1). 1.5mm from case for 10 seconds ℃ 300 Temp.rise at full load 15 30 Cooling Free air convection Case material Plastic(UL94-V0) Short circuit protection* Continuous 1 MTBF s 3500 Weight K hours 4.3 g *Supply voltage must be discontinued at the end of short circuit duration. TYPICAL CHARACTERISTICS Temperature Derating Graph In some circuits which are sensitive to noise and ripple.a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). Vin (VDC) 5 12 24 -- EXTERNAL CAPACITOR TABLE (TABLE 1) Cin Single Vout Cout Dual Vou (μF) 47 2.2 1.0 -- (VDC) 5 9 12 15 (μF) 10.0 4.7 2.2 1.0 (VDC) ±5 ±9 ±12 ±15 Cout (μF) 4.7 2.2 1.0 0.47 It's not recommend to connect any external capacitor in the application field with less than 0.5 watt output. Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connec ted to the inp ut or out put end in ser i es (F ig ur e 2) . OUTLINE DIMENSIONS & PIN CONNECTIONS SIZE Graph RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) FOOTPRINT DETAILS Pin 1 2 5 6 7 Note: Unit:mm(inch) Pin section:0.50*0.3mm(0.020*0.012inch) Pin section tolerances: 0.10mm( 0.004inch) General tolerances: ±0.25mm(±0.010inch) Single VIN GND 0V No Pin +V0 Dual VIN GND -V0 0V +V0 When the environment temperature is higher than 71°C, the 71° product output power should be less than 60% of the tha rated power. No parallel connection or plug and play. Requirement on output load To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load(namely full load).During operation, make sure the specified range of input voltage is not exceeded,the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:tech@microdc.cn Website:http://www.microdc.cn REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 Page 2 of 2