IExxooXS-1W

IE-XS-1W Series FIXED INPUT,ISOLATED®ULATED Dual Output DC/DC Converter SELECTION GUIDE Input Output Efficiency (%,Typ) Nominal Range Max Min IE0505XS-1W 5 4.75-5.25 ±5 ±100 ±10 69 83 IE0509XS-1W 5 4.75-5.25 ±9 ±56 ±6 61 83 IE0512XS-1W 5 4.75-5.25 ±12 ±42 ±5 62 83 IE0515XS-1W 5 4.75-5.25 ±15 ±33 ±4 64 250 IE1205XS-1W 12 11.4-12.6 ±5 ±100 ±10 72 100 IE1209XS-1W 12 11.4-12.6 ±9 ±56 ±6 61 83 IE1212XS-1W 12 11.4-12.6 ±12 ±42 ±5 63 83 IE1215XS-1W 12 11.4-12.6 ±15 ±33 ±4 64 83 IE2405XS-1W 24 22.8-25.2 ±5 ±100 ±10 72 83 IE2409XS-1W 24 22.8-25.2 ±9 ±56 ±6 60 83 IE2412XS-1W 24 22.8-25.2 ±12 ±42 ±5 63 83 IE2415XS-1W FEATURES RoHS compliant ◆ Efficiency up to 86% ◆ SIP10 Package ◆ Wide temperature performance at full ◆ 1 Watt load,-40°C to 85°C 24 22.8-25.2 ±15 ±33 ±4 64 300 UL 94V-0 package material ◆ Voltage(VDC) Current(MA) Switching Frequency (KHz,Typ) Voltage (VDC) Order code NOTICE:add Suffix “P” for Continuous Short Circuit Protection, e.g. IE0505XS-1WP NOTICE:add IE0505XS-1WP No heat sink required ◆ Low ripple and good EMC Features ◆ Industry standard pin out ◆ Power sharing on output ◆ 3KVDC isolation ◆ Continuous Short Circuit Protection ◆ ISOLATION SPECIFICATIONS Internal SMD construction ◆ Parameter Min. Flash tested for 1 minute and 1mA max 3000 VDC Isolation resistance Good dynamic feature Test conditions Isolation test voltage No external components required ◆ Typ. Max. Units Test at Viso=500VDC 1000 MΩ ◆ MODEL SELECTION IE①05②05③X④ S⑤-1W⑥ ①Product Series ③Output Voltage ⑤SIP Package ②Input Voltage ④Fixed Input ⑥Rated Power APPLICATIONS The IE_XS-1W series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) where the voltage of the input power supply is fixed (voltage variation ≤±5%); 2) where isolation is necessary between input and output (isolation voltage ≤3000VDC); 3) where the regulation of the output voltage and the output ripple noise are demanded. OUTPUT SPECIFICATIONS Parameter Test conditions Output power Min Typ. 0.1 Max. Units 1 W Line regulation For Vin change of ±5% ±0.25 % Load regulation 10% to 100% full load ±1 % Output voltage accuracy 100% full load ±3 % Temperature drift 100% full load 0.03 %/°C Output Ripple* 20MHz Bandwidth 10 20 MV p-p Output Noise* 20MHz Bandwidth 50 100 MV p-p Full load,nominal input 100 Switching frequency Khz * Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power Converter section, application notes. MICRODC RESERVES THE COPYRIGHT http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 Page 1 of 2 IE-XS-1W Series TEMPERATURE CHARACTERISTICS Parameter Conditions Filtering Min. Typ. Storage humidity range Units 95 Storage temperature 20 Temp.rise at full load Cooling °C 30 -55 1.5mm from case for 10 seconds °C 125 -40 % 85 °C 300 Operating temperature Lead temperature Max. To get an extreme low ripple,an "LC"filtering network may be connected to the input and output ends of the DC/DC converter.Which may produce a more significant filtering effect.It should also be noted that the inductance and the frequency of the "LC"filtering network should be staggered with the DC/DC frequency to avoid mutual interference see (Figure 1). °C Free air convection Case material Plastic(UL94-V0) IE-XS-1WP Continuous Short circuit protection 1 MTBF S 3500 K hours Weight 5.2 g *Supply voltage must be discontinued at the end of short circuit duration. TYPICAL CHARACTERISTICS In some circuits which are sensitive to noise and ripple.a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). Temperature Derating Graph EXTERNAL CAPACITOR TABLE (TABLE 1) Cin Vout Vin (VDC) 5 12 24 - OUTLINE DIMENSIONS & PIN CONNECTIONS SIZE Graph (μF) 4.7 Cout (VDC) ±5 (μF) 4.7 2.2 ±9 2.2 1.0 ±12 1 - ±15 0.47 It's not recommend to connect any external capacitor in the application field with less than 0.5 watt output. RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits.The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. FOOTPRINT DETAILS Pin VIN 2 GND 7 +V0 9 -V0 10 Note: Unit:mm(inch) Pin section:0.50*0.3mm(0.020*0.012inch) Pin section tolerances:±0.10mm(±0.004inch) General tolerances:±0.25mm(±0.010inch) Function 1 0V When the environment temperature is higher than 71 , the product output power should be less then 71℃, 60% of the rated power. No parallel connection or plug and play. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.Another 24V products, please inquire Our technical department! Requirement on output load To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load(namely full load).During operation, make sure the specified range of input voltage is not exceeded,the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! Use dual output simultaneously, forbid opening output pin (0V) to use as single output. RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:tech@microdc.cn Website:http://www.microdc.cn REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 Page 2 of 2