WRBxxooYD-6W

WRA-YD-6W＆WRB-YD -6W Series 6W, WIDE INPUT, ISOLATED & REGULATED DUAL&SINGLE OUTPUT DC-DC CONVERTER SELECTION GUIDE Input Output Efficiency Order code Voltage(VDC) Current(mA) Voltage (%.Typ.) (VDC) Max. Min. 11 ±5 ±600 ±60 76 11 ±12 ±250 ±25 81 4.5-9 11 ±15 ±200 ±20 83 5 4.5-9 11 5 1200 120 76 WRB0512YD-6W 5 4.5-9 11 12 500 50 81 WRB0515YD-6W 5 4.5-9 11 15 400 40 81 WRA1205YD-6W 12 9-18 22 ±5 ±600 ±60 76 WRA1212YD-6W 12 9-18 22 ±12 ±250 ±25 81 WRA1215YD-6W 12 9-18 22 ±15 ±200 ±20 83 WRB1203YD-6W 12 9-18 22 3.3 1500 150 74 WRB1205YD-6W 12 9-18 22 5 1200 120 76 WRB1212YD-6W 12 9-18 22 12 500 50 81 WRB1215YD-6W 12 9-18 22 15 400 40 81 WRA2405YD-6W 24 18-36 40 ±5 ±600 ±60 76 WRA2412YD-6W 24 18-36 40 ±12 ±250 ±25 81 WRA2415YD-6W 24 18-36 40 ±15 ±200 ±20 83 WRB2403YD-6W 24 18-36 40 3.3 1500 150 74 WRB2405YD-6W 24 18-36 40 5 1200 120 76 WRB2407YD-6W 24 18-36 40 7 857.1 85.71 78 WRB2412YD-6W 24 18-36 40 12 500 50 81 WRB2415YD-6W 24 18-36 40 15 400 40 81 WRA4805YD-6W 48 36-72 80 ±5 ±600 ±60 85 WRA4812YD-6W 48 36-72 80 ±12 ±250 ±25 83 WRA4815YD-6W 48 36-72 80 ±15 ±200 ±20 85 WRB4803YD-6W 48 36-72 80 3.3 1500 150 74 WRB4805YD-6W 48 36-72 80 5 1200 120 78 WRB4812YD-6W 48 36-72 80 12 500 50 80 WRB4815YD-6W 48 36-72 80 15 400 40 80 Nominal ◆1500VDC Isolation ◆Operating Temperature: -40℃～﹢85℃ ◆Five sided metal shielding ◆No external component required ◆Internal SMD construction ◆RoHS Compliance ◆MTBF>1000Khours MODEL SELECTION ① ② ③ ④ ⑤ ⑥ WRB 24 15 Y D -6W ①Product Series ②Input Voltage ③Output Voltage ④Wide (2:1) Input Range ⑤DIP24 Package Style ⑥Rated Power APPLICATIONS The WRA_YD-6W&WRB_YD-6W Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board.These products apply to: 1) Where the voltage of the input power supply is wide range (Voltage range≤2:1) 2) Where isolation is necessary between input and output(Isolation voltage≤1500VDC) 3) Where the regulation of the Output voltage and the output ripple noise are demanded. 4.5-9 5 4.5-9 WRA0515YD-6W ◆Short Circuit Protection(automatic recovery) 5 WRA0512YD-6W ◆Wide (2:1) Input Range Max* WRA0505YD-6W FEATURES Range 5 WRB0505YD-6W *Input voltage can't exceed this value,or will cause the permanent damage. COMMON SPECIFICATIONS Parameter Conditions Min. Max. Storage humidity Units 95 % Operating temperature -40 85 ℃ Storage temperature -55 125 ℃ Temp. rise at full load PRODUCT ID DESCRIPTION Typ. Lead temperature ℃ 40 300 1.5mm from case for 10 seconds No-load power 0.2 ℃ W Cooling Free Air Convection Short circuit protection Continuous,automatic recovery Case material Steel,nickel coated, copper Isolation voltage Tested for1 minute and 1mA 1500 VDC Isolation resistance Test at 500VDC 1000 MΩ Isolation Capacitance Input/Output MTBF MICRODC RESERVES THE COPYRIGHT http://www.microdc.cn Weight 85 1000 pF K hours 17 Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 g Page 1 of 3 WRA-YD-6W＆WRB-YD -6W Series TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Output power See below products program 0.6 Positive voltage accuracy Refer to recommended circuit Negative voltage accuracy TYPICAL CHARACTERISTICS Typ. Max. Units 6 W ±1 ±3 % Refer to recommended circuit ±3 ±5 % Load regulation From 10% to 100% load ±0.5 ±1* % Ripple ** 20MHz Bandwidth 20 50 mVp-p Temperature drift (Vout) Refer to recommended circuit ±0.02 Line regulation Input voltage from low to high ±0.2 ±0.5 % Noise** 20MHz Bandwidth 50 100 mVp-p Switching frequency 100% load, input voltage range 300 Temperature Derating Graph %/℃ KHz RECOMMENDED CIRCUIT * Dual output models unbalanced load: ±5%. ** Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, Output Graph application notes. Case material APPLICATION NOTE Requirement on output load In order to ensure the product operate efficiently and reliably,in addition to a max load(namely full load), a minimum load is specified for this kind of DC/DC converter.Make sure the specified range of input voltage is not exceeded,the minimum output load no less than 10% load the actual load.If load is less than the specified minimum load, the output ripple may increase sharply while its efficiency and reliability will reduce greatly.If the actual output power is very small,please add an appropriate resistor as extra loading,or contact our company for other lower output power products. Recommended Circuit All the WRA_YD-6W&WRB_YD-6W Series have been tested according to the following recommended testing circuit before leaving factory.This series should be tested under load(See figure 1). If you want to further decrease the input/output ripple,you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). General: Cin: 5V＆12V 100μF 24V＆48V 100μF-47μF Cout: 10μF/100mA Output External Capacitor Table(Table 1) Single Vout Dual Vout Cout (μF) (VDC) (μF) 3.3 2200 ±5 680 5 1000 ±12 330 12 470 ±15 220 15 While using unstable power source,please ensure the output voltage and ripple voltage do not exceed indexes of the converter. Input current of power supply should afford the startup current of this kind of DC/DC module (See figure 2). General:Ip≤1.4*Iin-max Cout (VDC) Input current 330 -- -- No parallel connection or plug and play http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646 Page 2 of 3 WRA-YD-6W＆WRB-YD -6W Series OUTLINE DIMENSIONS ＆ FOOTPRINT DETAILS MECHANICAL DIMENSIONS RECOMMENDED FOOTPRINT RECOMMENDED FOOTPRINT Top view grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) Note: Unit:mm[inch] Pin section tolerances:±0.10mm[±0.004inch] General tolerances:±0.25mm[±0.010inch] FOOTPRINT DETAILS TUBE OUTLINE DIMENSIONS Pin Single Dual 2、3 GND GND 9 NC 0V 11 NC -Vo 14 +Vo +Vo 16 0V 0V Vin Vin 22、23 NC:No connection When the environment temperature is higher than 71 , the product output power should be less 71℃, then 60% of the rated power. No parallel connection or plug and play. Use dual output simultaneously,forbid pening output pin (0V) to use as single output. Note: Unit :mm[inch] General tolerances:±0.50mm[±0.020inch] L=530mm[20.866inch] Tube Quantity: 15pcs Note: L=220mm[8.661inch] Tube Quantity: 6pcs 1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically. 2. Operation under 10% load will not damage the converter; However, they may not meet all specification listed. 3. All specifications measured at Ta=25°C, humidity