MT4LC8M8C2DJ-5

8 MEG x 8 EDO DRAM DRAM FEATURES • Single +3.3V ±0.3V power supply • Industry-standard x8 pinout, timing, functions, and packages • 12 row, 11 column addresses (C2) or 13 row, 10 column addresses (P4) • High-performance CMOS silicon-gate process • All inputs, outputs and clocks are LVTTLcompatible • Extended Data-Out (EDO) PAGE MODE access • 4,096-cycle CAS#-BEFORE-RAS# (CBR) REFRESH distributed across 64ms • Optional self refresh (S) for low-power data retention MT4LC8M8P4, MT4LC8M8C2 For the latest data sheet, please refer to the Micron Web site: www.micronsemi.com/mti/msp/html/datasheet.html PIN ASSIGNMENT (Top View) 32-Pin SOJ VCC DQ0 DQ1 DQ2 DQ3 NC VCC WE# RAS# A0 A1 A2 A3 A4 A5 VCC 32-Pin TSOP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VSS DQ7 DQ6 DQ5 DQ4 VSS CAS# OE# NC/A12** A11 A10 A9 A8 A7 A6 VSS OPTIONS • Refresh Addressing 4,096 (4K) rows 8,192 (8K) rows • Plastic Packages 32-pin SOJ (400 mil) 32-pin TSOP (400 mil) • Timing 50ns access 60ns access • Refresh Rates Standard Refresh (64ms period) Self Refresh (128ms period) MARKING C2 P4 DJ TG -5 -6 None S* 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC VSS DQ0 DQ7 DQ1 DQ6 DQ2 DQ5 DQ3 DQ4 NC Vss VCC CAS# WE# RAS# OE# NC/A12** A0 A1 A11 A2 A10 A3 A9 A4 A8 A5 A7 VCC A6 VSS **NC on C2 version and A12 on P4 version 8 MEG x 8 EDO DRAM PART NUMBERS PART NUMBER MT4LC8M8C2DJ-x MT4LC8M8C2DJ-x S MT4LC8M8C2TG-x MT4LC8M8C2TG-x S MT4LC8M8P4DJ-x MT4LC8M8P4DJ-x S MT4LC8M8P4TG-x MT4LC8M8P4TG-x S x = speed REFRESH ADDRESSING 4K 4K 4K 4K 8K 8K 8K 8K PACKAGE REFRESH SOJ SOJ TSOP TSOP SOJ SOJ TSOP TSOP Standard Self Standard Self Standard Self Standard Self NOTE: 1. The 8 Meg x 8 EDO DRAM base number differentiates the offerings in one place— MT4LC8M8C2. The fifth field distinguishes the address offerings: C2 designates 4K addresses and P4 designates 8K addresses. 2. The “#” symbol indicates signal is active LOW. *Contact factory for availability Part Number Example: GENERAL DESCRIPTION The 8 Meg x 8 DRAM is a high-speed CMOS, dynamic random-access memory devices containing 67,108,864 bits and designed to operate from 3V to 3.6V. The MT4LC8M8C2 and MT4LC8M8P4 are functionally organized as 8,388,608 locations containing eight bits each. The 8,388,608 memory locations are arranged in 4,096 rows by 2,048 columns on the C2 version and 8,192 rows by 1,024 columns on the P4 version. During READ or WRITE cycles, each location is MT4LC8M8C2DJ-5 KEY TIMING PARAMETERS SPEED -5 -6 tRC tRAC tPC tAA tCAC tCAS 84ns 104ns 50ns 60ns 20ns 25ns 25ns 30ns 13ns 15ns 8ns 10ns 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 1 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM FUNCTIONAL BLOCK DIAGRAM MT4LC8M8P4 (13 row addresses) WE# CAS# DATA-IN BUFFER 8 DQ0DQ7 CONTROL LOGIC NO. 2 CLOCK GENERATOR DATA-OUT BUFFER 8 8 OE# 10 COLUMNADDRESS BUFFER(10) REFRESH CONTROLLER 10 COLUMN DECODER 1,024 SENSE AMPLIFIERS I/O GATING 1,024 x 8 8 A0A12 REFRESH COUNTER ROW SELECT 13 13 ROWADDRESS BUFFERS (13) COMPLEMENT SELECT ROW DECODER 13 8,192 8,192 x 8 8,192 x 1,024 x 8 MEMORY ARRAY RAS# NO. 1 CLOCK GENERATOR VDD VSS FUNCTIONAL BLOCK DIAGRAM MT4LC8M8C2 (12 row addresses) WE# CAS# DATA-IN BUFFER 8 DQ0DQ7 CONTROL LOGIC NO. 2 CLOCK GENERATOR DATA-OUT BUFFER 8 8 OE# 11 COLUMNADDRESS BUFFER(11) REFRESH CONTROLLER 11 COLUMN DECODER 2,048 SENSE AMPLIFIERS I/O GATING 2,048 x 8 8 A0A11 REFRESH COUNTER ROW SELECT 12 12 ROWADDRESS BUFFERS (12) COMPLEMENT SELECT ROW DECODER 12 4,096 4,096 x 8 4,096 x 2,048 x 8 MEMORY ARRAY RAS# NO. 1 CLOCK GENERATOR VDD VSS 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 2 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM GENERAL DESCRIPTION (continued) uniquely addressed via the address bits. First, the row address is latched by the RAS# signal, then the column address is latched by CAS#. Both devices provide EDOPAGE-MODE operation, allowing for fast successive data operations (READ, WRITE, or READ-MODIFYWRITE) within a given row. The 8 Meg x 8 DRAM must be refreshed periodically in order to retain stored data. EDO PAGE MODE DRAM READ cycles have traditionally turned the output buffers off (High-Z) with the rising edge of CAS#. If CAS# went HIGH and OE# was LOW (active), the output buffers would be disabled. The 8 Meg x 8 DRAM offers an accelerated page mode cycle by eliminating output disable from CAS# HIGH. This option is called EDO, and it allows CAS# precharge time (tCP) to occur without the output data going invalid (see READ and EDO-PAGE-MODE READ waveforms in the noted appendix). EDO operates like any DRAM READ or FAST-PAGEMODE READ, except data is held valid after CAS# goes HIGH, as long as RAS# and OE# are held LOW and WE# is held HIGH. OE# can be brought LOW or HIGH while CAS# and RAS# are LOW, and the DQs will transition between valid data and High-Z. Using OE#, there are two methods to disable the outputs and keep them disabled during the CAS# HIGH time. The first method is to have OE# HIGH when CAS# transitions HIGH and keep OE# HIGH for tOEHC thereafter. This will disable the DQs, and they will remain disabled (regardless of the state of OE# after that point) until CAS# falls again. The second method is to have OE# LOW when CAS# transitions HIGH and then bring OE# HIGH for a minimum of tOEP anytime during the CAS# HIGH period. This will disable the DQs, and they will remain disabled (regardless of the state of OE# after that point) until CAS# falls again (see Figure 1). During DRAM ACCESS Each location in the DRAM is uniquely addressable, as mentioned in the General Description. The data for each location is accessed via the eight I/O pins (DQ0DQ7). A logic HIGH on WE# dictates read mode, while a logic LOW on WE# dictates write mode. During a WRITE cycle, data-in (D) is latched by the falling edge of WE# or CAS#, whichever occurs last. An EARLY WRITE occurs when WE# is taken LOW prior to CAS# falling. A LATE WRITE or READ-MODIFY-WRITE occurs when WE# falls after CAS# is taken LOW. During EARLY WRITE cycles, the data outputs (Q) will remain High-Z, regardless of the state of OE#. During LATE WRITE or READ-MODIFY-WRITE cycles, OE# must be taken HIGH to disable the data outputs prior to applying input data. If a LATE WRITE or READ-MODIFYWRITE is attempted while keeping OE# LOW, no write will occur, and the data outputs will drive read data from the accessed location. RAS# V IH V IL CAS# V IH V IL ADDR V IH V IL ROW COLUMN (A) COLUMN (B) COLUMN (C) COLUMN (D) DQ V IOH V IOL OPEN VALID DATA (A) tOD tOES VALID DATA (A) VALID DATA (B) tOD tOEHC VALID DATA (C) tOD VALID DATA (D) OE# V IH V IL tOE tOEP The DQs go back to Low-Z if tOES is met. The DQs remain High-Z until the next CAS# cycle if tOEHC is met. The DQs remain High-Z until the next CAS# cycle if tOEP is met. DON’T CARE UNDEFINED Figure 1 OE# CONTROL of DQs 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 3 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EDO PAGE MODE (continued) other cycles, the outputs are disabled at tOFF time after RAS# and CAS# are HIGH or at tWHZ after WE# transitions LOW. The tOFF time is referenced from the rising edge of RAS# or CAS#, whichever occurs last. WE# can also perform the function of disabling the output drivers under certain conditions, as shown in Figure 2. EDO-PAGE-MODE operations are always initiated with a row address strobed in by the RAS# signal, followed by a column address strobed in by CAS#, just like for single location accesses. However, subsequent column locations within the row may then be accessed at the page mode cycle time. This is accomplished by cycling CAS# while holding RAS# LOW and entering new column addresses with each CAS# cycle. Returning RAS# HIGH terminates the EDO-PAGE-MODE operation. covers all rows. The CBR REFRESH cycle will invoke the internal refresh counter for automatic RAS# addressing. Alternatively, RAS#-ONLY REFRESH capability is inherently provided. However, with this method, some compatibility issues may become apparent. For example, both C2 and P4 versions require 4,096 CBR REFRESH cycles, yet each requires a different number of RAS#-ONLY REFRESH cycles (C2 = 4,096 and P4 = 8,192). JEDEC strongly recommends the use of CBR REFRESH for this device. An optional self refresh mode is also available on the “S” version. The self refresh feature is initiated by performing a CBR REFRESH cycle and holding RAS# LOW for the specified tRASS. The “S” option allows for an extended period of 128ms, or 31.25µs per row for a 4K refresh and 15.625µs per row for an 8K refresh, when using a distributed CBR REFRESH. This refresh rate can be applied during normal operation, as well as during a standby or battery backup mode. The self refresh mode is terminated by driving RAS# HIGH for a minimum time of tRPS. This delay allows for the completion of any internal refresh cycles that may be in process at the time of the RAS# LOW-to-HIGH transition. If the DRAM controller uses a distributed CBR refresh sequence, a burst refresh is not required upon exiting self refresh. However, if the DRAM controller utilizes a RAS#-ONLY or burst CBR refresh sequence, all 1,024 rows must be refreshed using a minimum tRC refresh rate prior to resuming normal operation. DRAM REFRESH The supply voltage must be maintained at the specified levels, and the refresh requirements must be met in order to retain stored data in the DRAM. The refresh requirements are met by refreshing all 8,192 rows (P4) or all 4,096 rows (C2) in the DRAM array at least once every 64ms. The recommended procedure is to execute 4,096 CBR REFRESH cycles, either uniformly spaced or grouped in bursts, every 64ms. The MT4LC8M8P4 internally refreshes two rows for every CBR cycle, whereas the MT4LC8M8C2 refreshes one row for every CBR cycle. So with either device, executing 4,096 CBR cycles RAS# V IH V IL CAS# V IH V IL ADDR V IH V IL ROW COLUMN (A) COLUMN (B) COLUMN (C) COLUMN (D) DQ V IOH V IOL OPEN VALID DATA (A) tWHZ VALID DATA (B) tWHZ INPUT DATA (C) WE# V IH V IL V IH V IL tWPZ OE# The DQs go to High-Z if WE# falls and, if tWPZ is met, will remain High-Z until CAS# goes LOW with WE# HIGH (i.e., until a READ cycle is initiated). WE# may be used to disable the DQs to prepare for input data in an EARLY WRITE cycle. The DQs will remain High-Z until CAS# goes LOW with WE# HIGH (i.e., until a READ cycle is initiated). DON’T CARE UNDEFINED Figure 2 WE# CONTROL of DQs 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 4 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Relative to VSS ................ -1V to +4.6V Voltage on NC, Inputs or I/O Pins Relative to VSS ....................................... -1V to +4.6V Operating Temperature, TA (ambient) ... 0°C to +70°C Storage Temperature (plastic) ............ -55°C to +150°C Power Dissipation ................................................... 1W *Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS (Note: 1) (VCC = +3.3V ±0.3V) PARAMETER/CONDITION SUPPLY VOLTAGE INPUT HIGH VOLTAGE: Valid Logic 1; All inputs, I/Os and any NC INPUT LOW VOLTAGE: Valid Logic 0; All inputs, I/Os and any NC INPUT LEAKAGE CURRENT: Any input at VIN (0V ≤ VIN ≤ VCC + 0.3V); All other pins not under test = 0V OUTPUT HIGH VOLTAGE: IOUT = -2mA OUTPUT LOW VOLTAGE: IOUT = 2mA OUTPUT LEAKAGE CURRENT: Any output at VOUT (0V ≤ VOUT ≤ VCC + 0.3V); DQ is disabled and in High-Z state SYMBOL VCC VIH VIL II MIN 3 2 -0.3 -2 MAX 3.6 VCC + 0.3 0.8 2 UNITS NOTES V V V µA 26 26 27 VOH VOL IOZ 2.4 – -5 – 0.4 5 V V µA 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 5 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM ICC OPERATING CONDITIONS AND MAXIMUM LIMITS (Notes: 1, 2, 3, 5, 6) (VCC = +3.3V ±0.3V) PARAMETER/CONDITION STANDBY CURRENT: TTL (RAS# = CAS# = VIH) STANDBY CURRENT: CMOS (RAS# = CAS# VCC - 0.2V; DQs may be left open; other inputs: VIN VCC - 0.2V or VIN ≤ 0.2V) OPERATING CURRENT: Random READ/WRITE Average power supply current (RAS#, CAS#, address cycling: tRC = tRC [MIN]) OPERATING CURRENT: EDO PAGE MODE Average power supply current (RAS# = VIL, CAS#, address cycling: tPC = tPC [MIN]) REFRESH CURRENT: RAS#-ONLY Average power supply current (RAS# cycling, CAS# = VIH: tRC = tRC [MIN]) REFRESH CURRENT: CBR Average power supply current (RAS#, CAS#, address cycling: tRC = tRC [MIN]) REFRESH CURRENT: Extended (“S” version only) Average power supply current: CAS# = 0.2V or CBR cycling; RAS# = tRAS (MIN); WE# = VCC - 0.2V; A0-A11, OE# and DIN = VCC - 0.2V or 0.2V (DIN may be left open) REFRESH CURRENT: Self (“S” version only) Average power supply current: CBR with RAS# tRASS (MIN) and CAS# held LOW; WE# = VCC - 0.2V; A0-A11, OE# and DIN = VCC - 0.2V or 0.2V (DIN may be left open) SYMBOL ICC1 SPEED ALL 4K 8K REFRESH REFRESH UNITS NOTES 1 1 mA ICC2 ICC3 ALL -5 -6 -5 -6 -5 -6 -5 -6 500 175 165 155 125 175 165 165 155 500 135 125 155 125 135 125 165 155 µA mA 25 ICC4 mA 25 ICC5 mA 22 ICC6 mA 4, 7 ICC7 ALL 400 400 µA 4, 7 ICC8 ALL 350 400 µA 4, 7 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 6 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM CAPACITANCE (Note: 2) PARAMETER Input Capacitance: Address pins Input Capacitance: RAS#, CAS#, WE#, OE# Input/Output Capacitance: DQ SYMBOL CI 1 CI 2 CIO MAX 5 7 7 UNITS pF pF pF AC ELECTRICAL CHARACTERISTICS (Notes: 5, 6, 7, 8, 9, 10, 11, 12) (VCC = +3.3V ±0.3V) AC CHARACTERISTICS PARAMETER Access time from column address Column-address setup to CAS# precharge Column-address hold time (referenced to RAS#) Column-address setup time Row-address setup time Column address to WE# delay time Access time from CAS# Column-address hold time CAS# pulse width CAS# LOW to “Don’t Care” during Self Refresh CAS# hold time (CBR Refresh) CAS# to output in Low-Z Data output hold after CAS# LOW CAS# precharge time Access time from CAS# precharge CAS# to RAS# precharge time CAS# hold time CAS# setup time (CBR Refresh) CAS# to WE# delay time Write command to CAS# lead time Data-in hold time Data-in setup time Output disable Output enable time OE# hold time from WE# during READ-MODIFY-WRITE cycle OE# HIGH hold time from CAS# HIGH OE# HIGH pulse width OE# LOW to CAS# HIGH setup time Output buffer turn-off delay -5 SYMBOL tAA tACH tAR tASC tASR tAWD tCAC tCAH tCAS tCHD tCHR tCLZ tCOH tCP tCPA tCRP tCSH tCSR tCWD tCWL tDH tDS tOD tOE tOEH tOEHC tOEP tOES tOFF -6 MAX 25 MIN 15 45 0 0 49 13 15 10 10 15 10 0 3 10 5 45 5 35 10 10 0 0 10 10 5 5 0 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns NOTES MIN 12 38 0 0 42 8 8 15 8 0 3 8 5 38 5 28 8 8 0 0 8 5 5 4 0 18 10,000 4 13 28 35 4 18 19 19 23, 24 20 24 12 12 15 15 12 15 17, 23 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 7 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM AC ELECTRICAL CHARACTERISTICS (Notes: 5, 6, 7, 8, 9, 10, 11, 12) (VCC = +3.3V ±0.3V) AC CHARACTERISTICS PARAMETER OE# setup prior to RAS# during HIDDEN REFRESH cycle EDO-PAGE-MODE READ or WRITE cycle time EDO-PAGE-MODE READ-WRITE cycle time Access time from RAS# RAS# to column-address delay time Row-address hold time RAS# pulse width RAS# pulse width (EDO PAGE MODE) RAS# pulse width during Self Refresh Random READ or WRITE cycle time RAS# to CAS# delay time READ command hold time (referenced to CAS#) READ command setup time Refresh period Refresh period (2,048 cycles) “S” version RAS# precharge time RAS# to CAS# precharge time RAS# precharge time exiting Self Refresh READ command hold time (referenced to RAS#) RAS# hold time READ-WRITE cycle time RAS# to WE# delay time WRITE command to RAS# lead time Transition time (rise or fall) WRITE command hold time WRITE command hold time (referenced to RAS#) WE# command setup time WE# to outputs in High-Z WRITE command pulse width WE# pulse widths to disable outputs WE# hold time (CBR Refresh) WE# setup time (CBR Refresh) -5 SYMBOL tORD tPC tPRWC tRAC tRAD tRAH tRAS tRASP tRASS tRC tRCD tRCH tRCS tREF tREF tRP tRPC tRPS tRRH tRSH tRWC tRWD tRWL tT tWCH tWCR tWCS tWHZ tWP tWPZ tWRH tWRP MIN 0 20 47 9 9 50 50 100 84 11 0 0 MAX MIN 0 25 56 12 10 60 60 100 104 14 0 0 -6 MAX UNITS ns ns ns ns ns ns ns ns µs ns ns ns ns ms ms ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns NOTES 50 60 15 10,000 125,000 10,000 125,000 14 16 23 64 128 30 5 90 0 13 116 67 13 2 8 38 0 5 10 8 8 40 5 105 0 15 140 79 15 2 10 45 0 5 10 10 10 64 128 16 18 50 50 18 12 15 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 8 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM NOTES 1. All voltages referenced to VSS. 2. This parameter is sampled. VCC = +3.3V; f = 1 MHz; TA = 25°C. 3. ICC is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time and the outputs open. 4. Enables on-chip refresh and address counters. 5. The minimum specifications are used only to indicate cycle time at which proper operation over the full temperature range is ensured. 6. An initial pause of 100µs is required after powerup, followed by eight RAS# refresh cycles (RAS#ONLY or CBR with WE# HIGH), before proper device operation is ensured. The eight RAS# cycle wake-ups should be repeated any time the tREF refresh requirement is exceeded. 7. AC characteristics assume tT = 2.5ns. 8. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times are measured between VIH and VIL (or between VIL and VIH). 9. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 10. If CAS# and RAS# = VIH, data output is High-Z. 11. If CAS# = VIL, data output may contain data from the last valid READ cycle. 12. Measured with a load equivalent to two TTL gates and 100pF; and VOL = 0.8V and VOH = 2V. 13. If CAS# is LOW at the falling edge of RAS#, output data will be maintained from the previous cycle. To initiate a new cycle and clear the dataout buffer, CAS# must be pulsed HIGH for tCP. 14. The tRAD (MAX) limit is no longer specified. tRAD (MAX) was specified as a reference point only. If tRAD was greater than the specified tRAD (MAX) limit, then access time was controlled exclusively by tAA (tRAC and tCAC no longer applied). With or without the tRAD (MAX) limit, tAA, tRAC, and tCAC must always be met. 15. The tRCD (MAX) limit is no longer specified. tRCD (MAX) was specified as a reference point only. If tRCD was greater than the specified tRCD (MAX) limit, then access time was controlled exclusively by tCAC (tRAC [MIN] no longer applied). With or without the tRCD limit, tAA and tCAC must always be met. 16. Either tRCH or tRRH must be satisfied for a READ cycle. 17. tOFF (MAX) defines the time at which the output achieves the open circuit condition and is not referenced to VOH or VOL. 18.tWCS, tRWD, tAWD, and tCWD are not restrictive operating parameters. tWCS applies to EARLY WRITE cycles. If tWCS > tWCS MIN, the cycle is an EARLY WRITE cycle and the data output will remain an open circuit throughout the entire cycle. tRWD, tAWD and tCWD define READMODIFY-WRITE cycles. Meeting these limits allows for reading and disabling output data and then applying input data. OE# held HIGH and WE# taken LOW after CAS# goes LOW results in a LATE WRITE (OE#-controlled) cycle. tWCS, tRWD, tCWD and tAWD are not applicable in a LATE WRITE cycle. 19. These parameters are referenced to CAS# leading edge in EARLY WRITE cycles and WE# leading edge in LATE WRITE or READ-MODIFY-WRITE cycles. 20. If OE# is tied permanently LOW, LATE WRITE or READ-MODIFY-WRITE operations are not possible. 21. A HIDDEN REFRESH may also be performed after a WRITE cycle. In this case, WE# is LOW and OE# is HIGH. 22. RAS#-ONLY REFRESH requires that all rows be refreshed at least once every 64ms (4,096 rows for the C2 version and 8,192 rows for the P4 version). CBR REFRESH requires that at least 4,096 cycles be completed every 64ms. 23. The DQs open during READ cycles once tOD or tOFF occur. If CAS# stays LOW while OE# is brought HIGH, the DQs will open. If OE# is brought back LOW (CAS# still LOW), the DQs will provide the previously read data. 24. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE# HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. If OE# is taken back LOW while CAS# remains LOW, the DQs will remain open. 25. Column address changed once each cycle. 26. VIH overshoot: VIH (MAX) = VCC + 2V for a pulse width ≤ 10ns, and the pulse width cannot be greater than one third of the cycle rate. VIL undershoot: VIL (MIN) = -2V for a pulse width ≤ 10ns, and the pulse width cannot be greater than one third of the cycle rate. 27. NC pins are assumed to be left floating and are not tested for leakage. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 9 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM READ CYCLE tRC tRAS V IH V IL tCSH tRSH tCRP CAS# V IH V IL tAR tASR tRAD tRAH tASC tACH V IH V IL tCAH tRCD tCAS tRRH tRP RAS# ADDR ROW tRCS COLUMN tRCH ROW WE# V IH V IL tAA tRAC tCAC tCLZ tOFF NOTE 1 DQ V OH V OL OPEN tOE VALID DATA tOD OPEN OE# V IH V IL DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tACH tAR tASC tASR tCAC tCAH tCAS tCLZ tCRP tCSH tOD tOE -6 MAX 25 MIN 15 45 0 0 13 15 10 10,000 10 0 5 45 0 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOFF tRAC tRAD tRAH tRAS tRC tRCD tRCH tRCS tRP tRRH tRSH -5 MIN 0 9 9 50 84 11 0 0 30 0 13 MAX 12 50 MIN 0 12 10 60 104 14 0 0 40 0 15 -6 MAX 15 60 UNITS ns ns ns ns ns ns ns ns ns ns ns ns MIN 12 38 0 0 8 8 0 5 38 0 10,000 10,000 12 12 15 15 NOTE: 1. tOFF is referenced from rising edge of RAS# or CAS#, whichever occurs last. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 10 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EARLY WRITE CYCLE tRC tRAS V IH V IL tCSH tRSH tCRP CAS# V IH V IL tRAD tASR ADDR V IH V IL tRAH tAR tASC tCAH tACH tRCD tCAS tRP RAS# ROW COLUMN tCWL tRWL tWCS tWCR tWCH tWP ROW WE# V IH V IL tDS tDH V DQ V IOH IOL V IH V IL VALID DATA OE# DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tACH tAR tASC tASR tCAH tCAS tCRP tCSH tCWL tDH tDS tRAD -6 MAX MIN 15 45 0 0 10,000 10 10 5 45 15 10 0 12 10,000 MAX UNITS ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tRAH tRAS tRC tRCD tRP tRSH tRWL tWCH tWCR tWCS tWP -5 MIN 9 50 84 11 30 13 13 8 38 0 5 MAX 10,000 MIN 10 60 104 14 40 15 15 10 45 0 5 -6 MAX 10,000 UNITS ns ns ns ns ns ns ns ns ns ns ns MIN 12 38 0 0 8 8 5 38 8 8 0 9 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 11 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE cycles) tRWC tRAS V IH V IL tCSH tRSH tCAS tRP RAS# tCRP V IH V IL tAR tRAD tRAH tRCD CAS# tASC tCAH tACH tASR ADDR V IH V IL ROW COLUMN tRWD tCWD tAWD tCWL tRWL tWP ROW tRCS WE# V IH V IL tAA tRAC tCAC tCLZ tDS VALID D OUT tOE V IH V IL tOD tDH V DQ V IOH IOL OPEN VALID D IN tOEH OPEN OE# DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tACH tAR tASC tASR tAWD tCAC tCAH tCAS tCLZ tCRP tCSH tCWD tCWL tDH tDS -6 MAX 25 MIN 15 45 0 0 49 13 15 10 10,000 10 0 5 45 35 10 10 0 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOD tOE tOEH tRAC tRAD tRAH tRAS tRCD tRCS tRP tRSH tRWC tRWD tRWL tWP -5 MIN 0 8 50 9 9 50 11 0 30 13 116 67 13 5 10,000 12 10 60 14 0 40 15 140 79 15 5 MAX 12 12 10 MIN 0 -6 MAX 15 15 60 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns MIN 12 38 0 0 42 8 8 0 5 38 28 8 8 0 10,000 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 12 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EDO-PAGE-MODE READ CYCLE tRASP V IH V IL tCSH tCRP CAS# V IH V IL tAR tASR ADDR V IH V IL tRAD tRAH tACH tASC tCAH tACH tASC tACH tCAH tASC tCAH tRCD tCAS tPC tCP tCAS tCP tRSH tCAS tCP tRP RAS# ROW tRCS COLUMN COLUMN COLUMN tRCH tRRH ROW WE# V IH V IL tAA tRAC tCAC tCLZ tAA tCPA tCAC tCOH VALID DATA tOE VALID DATA tOD tCLZ tOEHC tAA tCPA tCAC tOFF DQ V OH V OL OPEN VALID DATA tOE tOES tOEP tOD OPEN OE# V IH V IL tOES DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tACH tAR tASC tASR tCAC tCAH tCAS tCLZ tCOH tCP tCPA tCRP tCSH tOD tOE -6 MAX 25 MIN 15 45 0 0 13 15 10 10 0 3 10 28 35 5 45 12 12 0 15 15 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOEHC tOEP tOES tOFF tPC tRAC tRAD tRAH tRASP tRCD tRCH tRCS tRP tRRH tRSH -5 MIN 5 5 4 0 20 9 9 50 11 0 0 30 0 13 125,000 12 50 12 10 60 14 0 0 40 0 15 MAX MIN 10 5 5 0 25 -6 MAX UNITS ns ns ns 15 60 ns ns ns ns ns 125,000 ns ns ns ns ns ns ns MIN 12 38 0 0 8 8 0 3 8 5 38 0 10,000 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 13 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EDO-PAGE-MODE EARLY WRITE CYCLE t RASP V IH V IL t CSH t CRP V IH V IL t AR t RAD t ASR ADDR V IH V IL t RAH t ASC tACH t CAH t ASC t ACH t CAH t ASC t ACH t CAH t RCD t CAS t PC t CP t CAS t CP t RSH t CAS t CP t RP RAS# CAS# ROW COLUMN t CWL t WCS t WCH t WP COLUMN t CWL t WCS t WCH t WP COLUMN t CWL t WCS t WCH t WP ROW WE# V IH V IL t WCR t DS t DH t DS t DH t DS t RWL t DH V DQ V IOH IOL VALID DATA VALID DATA VALID DATA DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tACH tAR tASC tASR tCAH tCAS tCP tCRP tCSH tCWL tDH tDS -6 MAX MIN 15 45 0 0 10 10 10 5 45 10 10 0 MAX UNITS ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tPC tRAD tRAH tRASP tRCD tRP tRSH tRWL tWCH tWCR tWCS tWP -5 MIN 20 9 9 50 11 30 13 13 8 38 0 5 125,000 MAX MIN 25 12 10 60 14 40 15 15 10 45 0 5 -6 MAX UNITS ns ns ns 125,000 ns ns ns ns ns ns ns ns ns MIN 12 38 0 0 8 8 8 5 38 8 8 0 10,000 10,000 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 14 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EDO-PAGE-MODE READ-WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE cycles) t RASP V IH V IL t CSH t CRP V IH V IL t AR t RAD t ASR ADDR V IH V IL t RAH t ASC t CAH t ASC t CAH t ASC t CAH t RCD t CAS t CP t PC t PRWC NOTE 1 t CAS t CP t RSH t CAS t CP t RP RAS# CAS# ROW COLUMN t RWD t RCS t CWL t WP t AWD t CWD COLUMN COLUMN t RWL t CWL ROW t WP t AWD t CWD t AWD t CWD t CWL t WP WE# V IH V IL t AA t RAC t DH t DS t CAC t CLZ V IOH V IOL t AA t CPA t CAC t CLZ VALID D OUT VALID DIN VALID D OUT VALID D IN t AA t DH t DS tCPA t CAC t CLZ VALID D OUT VALID D IN t DH t DS DQ OPEN OPEN t OD t OE OE# V IH V IL t OE t OD t OE t OD t OEH DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tAR tASC tASR tAWD tCAC tCAH tCAS tCLZ tCP tCPA tCRP tCSH tCWD tCWL tDH tDS -6 MAX 25 MIN 45 0 0 49 13 15 10 10 0 10 28 35 5 45 35 10 10 0 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOD tOE tOEH tPC tPRWC tRAC tRAD tRAH tRASP tRCD tRCS tRP tRSH tRWD tRWL tWP -5 MIN 0 8 20 47 50 9 9 50 11 0 30 13 67 13 5 125,000 12 10 60 14 0 40 15 79 15 5 MAX 12 12 MIN 0 12 25 56 -6 MAX 15 15 UNITS ns ns ns ns ns 60 ns ns ns ns ns ns ns ns ns ns ns MIN 38 0 0 42 8 8 0 8 5 38 28 8 8 0 10,000 125,000 NOTE: 1. tPC is for LATE WRITE cycles only. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 15 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM EDO-PAGE-MODE READ EARLY WRITE CYCLE (Pseudo READ-MODIFY-WRITE) t RASP RAS# V IH V IL t CSH tPC tCRP CAS# V IH V IL tAR tRAD tASR ADDR V IH V IL tRAH ROW tASC tCAH t ASC t CAH tASC t ACH t CAH t RCD t CAS t CP t CAS tPC t CP t CAS tRSH t CP t RP COLUMN (A) tRCS COLUMN (B) tRCH COLUMN (N) tWCS tWCH ROW WE# V IH V IL tRAC tAA tCPA tCAC tAA tCAC tCOH t WHZ VALID DATA (B) t DS t DH DQ V IOH V IOL V IH V IL OPEN tOE VALID DATA (A) VALID DATA IN OE# DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tACH tAR tASC tASR tCAC tCAH tCAS tCOH tCP tCPA tCRP tCSH tDH tDS -6 MAX 25 MIN 15 45 0 0 13 15 10 10 3 10 28 35 5 45 10 0 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOE tPC tRAC tRAD tRAH tRASP tRCD tRCH tRCS tRP tRSH tWCH tWCS tWHZ -5 MIN 20 50 9 9 50 11 0 0 30 13 8 0 0 12 125,000 12 10 60 14 0 0 40 15 10 0 0 MAX 12 25 MIN -6 MAX 15 60 UNITS ns ns ns ns ns ns ns ns ns ns ns ns 15 ns ns MIN 12 38 0 0 8 8 3 8 5 38 8 0 125,000 10,000 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 16 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM READ CYCLE (with WE#-controlled disable) RAS# V IH V IL tCSH tCRP CAS# V IH V IL tAR tASR V IH V IL tRAD tRAH tASC tCAH tASC tRCD tCAS tCP ADDR ROW tRCS COLUMN tRCH tWPZ tRCS COLUMN WE# V IH V IL tAA tRAC tCAC tCLZ tWHZ tCLZ DQ V OH V OL OPEN tOE VALID DATA tOD OPEN OE# V IH V IL DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tAR tASC tASR tCAC tCAH tCAS tCLZ tCP tCRP tCSH -6 MAX 25 MIN 45 0 0 13 15 10 10 0 10 5 45 10,000 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns ns SYMBOL tOD tOE tRAC tRAD tRAH tRCD tRCH tRCS tWHZ tWPZ -5 MIN 0 MAX 12 12 50 9 9 11 0 0 12 10 10 12 10 14 0 0 MIN 0 -6 MAX 15 15 60 UNITS ns ns ns ns ns ns ns 15 ns ns ns MIN 38 0 0 8 8 0 8 5 38 10,000 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 17 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM RAS#-ONLY REFRESH CYCLE (OE# and WE# = DON’T CARE) tRC tRAS V IH V IL tCRP V IH V IL tASR ADDR V IH V IL tRAH tRPC tRP RAS# CAS# ROW ROW V DQ V OH OL OPEN CBR REFRESH CYCLE (Addresses and OE# = DON’T CARE) t RP RAS# V IH V IL t RPC t CP CAS# V IH V IL V OH V OL t WRP WE# V IH V IL t WRH OPEN t WRP t WRH t CSR t CHR t RPC t CSR t CHR t RAS NOTE 1 t RP t RAS DQ DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tASR tCHR tCP tCRP tCSR tRAH -6 MAX MIN 0 10 10 5 5 10 MAX UNITS ns ns ns ns ns ns SYMBOL tRAS tRC tRP tRPC tWRH tWRP -5 MIN 50 84 30 5 8 8 MAX 10,000 MIN 60 104 40 5 10 10 -6 MAX 10,000 UNITS ns ns ns ns ns ns MIN 0 8 8 5 5 9 NOTE: 1. End of first CBR REFRESH cycle. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 18 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM HIDDEN REFRESH CYCLE 1 (WE# = HIGH; OE# = LOW) tRAS RAS# V IH V IL tCRP CAS# V IH V IL tAR tRAD tASR V IH V IL tRAH tASC tCAH tRCD tRSH tCHR tRP tRAS ADDR ROW COLUMN tAA tRAC tCAC tCLZ tOFF V DQ V OH OL OPEN tOE VALID DATA tOD tORD OPEN V OE# V IH IL DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tAA tAR tASC tASR tCAC tCAH tCHR tCLZ tCRP tOD -6 MAX 25 MIN 45 0 0 13 15 10 10 0 12 5 0 15 MAX 30 UNITS ns ns ns ns ns ns ns ns ns ns SYMBOL tOE tOFF tORD tRAC tRAD tRAH tRAS tRCD tRP tRSH -5 MIN 0 0 50 9 9 50 11 30 13 10,000 12 10 60 14 40 15 MAX 12 12 MIN 0 0 -6 MAX 15 15 60 UNITS ns ns ns ns ns ns ns ns ns ns MIN 38 0 0 8 8 0 5 0 10,000 NOTE: 1. A HIDDEN REFRESH may also be performed after a WRITE cycle. In this case, WE# is LOW and OE# is HIGH. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 19 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM SELF REFRESH CYCLE (Addresses and OE# = DON’T CARE) tRP V IH V IL tRASS NOTE 1 (( )) (( )) tCSR tCHD (( )) (( )) (( )) tWRP tWRH (( )) (( )) OPEN tWRP tWRH tRPS NOTE 2 RAS# tRPC tCP tRPC tCP (( )) CAS# V IH V IL V DQ V OH OL V WE# V IH IL DON’T CARE UNDEFINED TIMING PARAMETERS -5 SYMBOL tCHD tCP tCSR tRASS tRP MIN 15 8 5 100 30 MAX MIN 15 10 5 100 40 -6 MAX UNITS ns ns ns µs ns SYMBOL tRPC tRPS tWRH tWRP MIN 5 90 8 8 -5 MAX MIN 5 105 10 10 -6 MAX UNITS ns ns ns ns NOTE: 1. Once tRASS (MIN) is met and RAS# remains LOW, the DRAM will enter self refresh mode. 2. Once tRPS is satisfied, a complete burst of all rows should be executed if RAS#-only or burst CBR refresh 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 20 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM 32-PIN PLASTIC SOJ (400 mil) .829 (21.05) .823 (20.90) .445 (11.31) .435 (11.05) .405 (10.29) .399 (10.13) PIN #1 ID .050 (1.27) TYP .750 (19.05) TYP .037 (0.95) MAX DAMBAR PROTRUSION .024 (0.61) .032 (0.82) .026 (0.67) .030 (0.76) MIN .145 (3.68) .132 (3.35) SEATING PLANE .020 (0.51) .015 (0.38) R .040 (1.02) .030 (0.77) .095 (2.42) .080 (2.03) .380 (9.65) .360 (9.14) NOTE: 1. All dimensions in inches (millimeters) MAX or typical where noted. MIN 2. Package width and length do not include mold protrusion; allowable mold protrusion is .01" per side. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 21 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc. 8 MEG x 8 EDO DRAM 32-PIN PLASTIC TSOP (400 mil) 20.96 ±0.08 SEE DETAIL A 1.27 TYP 0.95 11.76 ±0.10 10.16 ±0.08 PIN 1 ID 0.43 +0.07 -0.13 0.15 +0.03 -0.02 0.25 0.10 1.20 MAX 0.10 +0.10 -0.05 GAGE PLANE 0.80 TYP 0.50 ±0.10 DETAIL A NOTE: 1. All dimensions in millimeters MAX or typical where noted. MIN 2. Package width and length do not include mold protrusion; allowable mold protrusion is .25mm per side. 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 E-mail: prodmktg@micron.com, Internet: http://www.micron.com, Customer Comment Line: 800-932-4992 Micron is a registered trademark of Micron Technology, Inc. 8 Meg x 8 EDO DRAM D20_2.p65 – Rev. 5/00 22 Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2000, Micron Technology, Inc.