MT9123AP1

CMOS MT9123 Dual Voice Echo Canceller Data Sheet Features • • • • • • • • • • • • November 2005 Dual channel 64 ms or single channel 128 ms echo cancellation Conforms to ITU-T G.165 requirements Narrow-band signal detection Programmable double-talk detection threshold Non-linear processor with adaptive suppression threshold and comfort noise insertion Offset nulling of all PCM channels Controllerless mode or Controller mode with serial interface ST-BUS or variable-rate SSI PCM interfaces Selectable µ/A-Law ITU-T G.711; µ/A-Law Sign Mag; linear 2’s complement Per channel selectable 12 dB attenuator Transparent data transfer and mute option 19.2 MHz master clock operation Ordering Information MT9123AP 28 Pin PLCC Tubes MT9123AE 28 Pin PDIP Tubes MT9123APR 28 Pin PLCC Tape & Reel MT9123AP1 28 Pin PLCC* Tubes MT9123APR1 28 Pin PLCC* Tape & Reel *Pb Free Matte Tin -40°C to +85°C Description The MT9123 Voice Echo Canceller implements a cost effective solution for telephony voice-band echo cancellation conforming to ITU-T G.165 requirements. The MT9123 architecture contains two echo cancellers which can be configured to provide dual channel 64 millisecond echo cancellation or single channel 128 millisecond echo cancellation. The MT9123 operates in two major modes: Controller or Controllerless. Controller mode allows access to an array of features for customizing the MT9123 operation. Controllerless mode is for applications where default register settings are sufficient. Applications Wireless Telephony • Trunk echo cancellers Linear/ µ/A-Law Offset Null + Adaptive Filter Sin Programmable Bypass Linear/ µ/A-Law Sout Microprocessor Interface Double-Talk Detector Narrow-Band Detector Offset Null 12dB Attenuator Linear/ µ/A-Law Rout ENA2 ENB2 Non-Linear Processor Control • Linear/ µ/A-Law Rin ENA1 ENB1 CONFIG1 CONFIG2 S1/DATA1 S2/DATA2 S3/CS S4/SCLK Echo Canceller A NLP LAW FORMAT Echo Canceller B IC3 IC4 IC1 IC2 VDD VSS PWRDN F0od F0i BCLK/C4i Figure 1 - Functional Block Diagram 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 1996-2005, Zarlink Semiconductor Inc. All Rights Reserved. MCLK MT9123 PDIP ENB2 ENA2 ENB1 ENA1 CONFIG2 CONFIG1 BCLK/C4i CONFIG2 CONFIG1 BCLK/C4i F0i Rout Sout VDD F0od S1/DATA1 S2/DATA2 S3/CS S4/SCLK IC4 IC3 4 3 2 1 28 27 26 28 27 26 25 24 23 22 21 20 19 18 17 16 15 Rin Sin VSS MCLK IC1 NLP IC2 5 6 7 8 9 10 11 • PLCC 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 25 24 23 22 21 20 19 F0i Rout Sout VDD F0od S1/DATA1 S2/DATA2 LAW FORMAT PWRDN IC3 IC4 S4/SCLK S3/CS ENA1 ENB1 ENA2 ENB2 Rin Sin VSS MCLK IC1 NLP IC2 LAW FORMAT PWRDN Data Sheet Figure 2 - Pin Connections Pin Description Pin # Name 1 ENA1 Description SSI Enable Strobe / ST-BUS Mode for Rin/Sout (Input). This pin has dual functions depending on whether SSI or ST-BUS is selected. For SSI, this strobe must be present for frame synchronization. This is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for Echo Canceller A on Rin/Sout pins. Strobe period is 125 microseconds. For ST-BUS, this pin, in conjunction with the ENB1 pin, will select the proper ST-BUS mode for Rin/Sout pins (see ST-BUS Operation description). The selected mode applies to both Echo Canceller A and B. 2 ENB1 SSI Enable Strobe / ST-BUS Mode for Rin/Sout (Input). This pin has dual functions depending on whether SSI or ST-BUS is selected. For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for Echo Canceller B on Rin/Sout pins. Strobe period is 125 microseconds. For ST-BUS, this pin, in conjunction with the ENA1 pin, will select the proper ST-BUS mode for Rin/Sout pins (see ST-BUS Operation description). The selected mode applies to both Echo Canceller A and B. 3 ENA2 SSI Enable Strobe / ST-BUS Mode for Sin/Rout (Input). This pin has dual functions depending on whether SSI or ST-BUS is selected. For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for Echo Canceller A on Sin/Rout pins. Strobe period is 125 microseconds. For ST-BUS, this pin, in conjunction with the ENB2 pin, will select the proper ST-BUS mode for Sin/Rout pins (see ST-BUS Operation description). The selected mode applies to both Echo Canceller A and B. 2 Zarlink Semiconductor Inc. MT9123 Data Sheet Pin Description (continued) Pin # Name 4 ENB2 Description SSI Enable Strobe / ST-BUS Mode for Sin/Rout (Input). This pin has dual functions depending on whether SSI or ST-BUS is selected. For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for Echo Canceller B on Sin/Rout pins. Strobe period is 125 microseconds. For ST-BUS, this pin, in conjunction with the ENA2 pin, will select the proper ST-BUS mode for Sin/Rout pins (see ST-BUS Operation description). The selected mode applies to both Echo Canceller A and B. 5 Rin Receive PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input stream. Data may be in either companded or 2’s complement linear format. Two PCM channels are timemultiplexed on this pin. These are the Receive Input reference channels for Echo Cancellers A and B. Data bits are clocked in following SSI or ST-BUS timing requirements. 6 Sin Send PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input stream. Data may be in either companded or 2’s complement linear format. Two PCM channels are timemultiplexed on this pin. These are the Send Input channels (after echo path) for Echo Cancellers A and B. Data bits are clocked in following SSI or ST-BUS timing requirements. 7 VSS Digital Ground. Nominally 0 volts. 8 MCLK 9 IC1 Internal Connection 1 (Input). Must be tied to Vss. 10 NLP Non-Linear Processor Control (Input). Controllerless Mode: An active high enables the Non-Linear Processors in Echo Cancellers A and B. Both NLP’s are disabled when low. Intended for conformance testing to G.165 and it is usually tied to Vdd for normal operation. Master Clock (Input). Nominal 20 MHz Master Clock input. May be connected to an asynchronous (relative to frame signal) clock source. Controller Mode: This pin is ignored (tie to Vdd or Vss). The non-linear processor operation is controlled by the NLPDis bit in Control Register 2. Refer to the Register Summary. 11 IC2 Internal Connection 2 (Input). Must be tied to Vss. 12 LAW A/µ Law Select (Input). An active low selects µ−Law companded PCM. When high, selects A-Law companded PCM. This control is for both echo cancellers and is valid for both controller and controllerless modes. 13 FORMAT ITU-T/Sign Mag (Input). An active low selects sign-magnitude PCM code. When high, selects ITU-T (G.711) PCM code. This control is for both echo cancellers and is valid for both controller and controllerless modes. 14 PWRDN Power-down (Input). An active low resets the device and puts the MT9123 into a low-power stand-by mode. 15 IC3 Internal Connection 3 (Output). Must be left unconnected. 16 IC4 Internal Connection 4 (Output). Must be left unconnected. 3 Zarlink Semiconductor Inc. MT9123 Data Sheet Pin Description (continued) Pin # Name 17/18 S4/S3 Description Selection of Echo Canceller B Functional States (Input). Controllerless Mode: Selects Echo Canceller B functional states according to Table 2. Controller Mode: S4 and S3 pins become SCLK and CS pins respectively. 17 SCLK Serial Port Synchronous Clock (Input). Data clock for the serial microport interface. Chip Select (Input). Enables serial microport interface data transfers. Active low. 18 CS 19/20 S2/S1 Selection of Echo Canceller A Functional States (Input). Controllerless Mode: Selects Echo Canceller A functional states according to Table 2. Controller Mode: S2 and S1 pins become DATA2 and DATA1 pins respectively. 19 DATA2 20 DATA1 21 F0od Serial Data Receive (Input). In Motorola/National serial microport operation, the DATA2 pin is used for receiving data. In Intel serial microport operation, the DATA2 pin is not used and must be tied to Vss or Vdd. Serial Data Port (Bidirectional). In Motorola/National serial microport operation, the DATA1 pin is used for transmitting data. In Intel serial microport operation, the DATA1 pin is used for transmitting and receiving data. Delayed Frame Pulse Output (Output). In ST-BUS operation, this pin generates a delayed frame pulse after the 4th channel time slot and is used for daisy-chaining multiple ST-BUS devices. See Figures 4 to 7. In SSI operation, this pin outputs logic low. 22 VDD Positive Power Supply. Nominally 5 volts. 23 Sout Send PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM output stream. Data may be in either companded or 2’s complement linear PCM format. Two PCM channels are time-multiplexed on this pin. These are the Send Out signals after echo cancellation and Nonlinear processing. Data bits are clocked out following SSI or ST-BUS timing requirements. 24 Rout Receive PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM output stream. Data may be in either companded or 2’s complement linear PCM format. Two PCM channels are time-multiplexed on this pin. This output pin is provided for convenience in some applications and may not always be required. Data bits are clocked out following SSI or STBUS timing requirements. 25 F0i 26 Frame Pulse (input). In ST-BUS operation, this is a frame alignment low going pulse. SSI operation is enabled by connecting this pin to Vss. BCLK/C4i Bit Clock/ST-BUS Clock (Input). In SSI operation, BCLK pin is a 128 kHz to 4.096 MHz bit clock. This clock must be synchronous with ENA1, ENA2, ENB1 and ENB2 enable strobes. In ST-BUS operation, C4i pin must be connected to the 4.096 MHz (C4) system clock. 4 Zarlink Semiconductor Inc. MT9123 Data Sheet Pin Description (continued) Pin # Name Description 27/28 CONFIG1/ Device Configuration Pins (Inputs). When CONFIG1 and CONFIG2 pins are both logic 0, CONFIG2 the MT9123 serial microport is enabled. This configuration is defined as Controller Mode. When CONFIG1 and CONFIG2 pins are in any other logic combination, the MT9123 is configured in Controllerless Mode. See Table 3. Notes: 1. All unused inputs should be connected to logic low or high unless otherwise stated. All outputs should be left open circuit when not used. 2. All inputs have TTL compatible logic levels except for MCLK, Sin and Rin pins which have CMOS compatible logic levels and PWRDN pin which has Schmitt trigger compatible logic levels. 3. All outputs are CMOS pins with CMOS logic levels. Functional Description The MT9123 architecture contains two individually controlled echo cancellers (Echo Canceller A and B). They can be set in three distinct configurations: Normal, Back-to-Back and Extended Delay (see Figure 3). Under Normal configuration, the two echo cancellers are positioned in parallel providing 64 millisecond echo cancellation in two channels simultaneously. In Back-to-Back configuration, the two echo cancellers are positioned to cancel echo coming from both directions in a single channel. In Extended-Delay configuration, the two echo cancellers are internally cascaded into one 128 millisecond echo canceller. Each echo canceller contains the following main elements (see Figure 1). • Adaptive Filter for estimating the echo channel • Subtracter for cancelling the echo • Double-Talk detector for disabling the filter adaptation during periods of double-talk • Non-Linear Processor for suppression of residual echo • Narrow-Band Detector for preventing Adaptive Filter divergence caused by narrow-band signals • Offset Null filters for removing the DC component in PCM channels • 12 dB attenuator for signal attenuation • Serial controller interface compatible with Motorola, National and Intel microcontrollers • PCM encoder/decoder compatible with µ/A-Law ITU-T G.711, µ/A-Law Sign-Mag or linear 2’s complement coding The MT9123 has two modes of operation: Controllerless and Controller. Controllerless mode is intended for applications where customization is not required. Controller mode allows access to all registers for customizing the MT9123 operation. Refer to Table 7 for a complete list. Controller mode is selected when CONFIG1 and CONFIG2 pins are both connected to Vss. Each echo canceller in the MT9123 has four functional states: Mute, Bypass, Disable Adaptation and Enable Adaptation. These are explained in the section entitled Echo Canceller Functional States. 5 Zarlink Semiconductor Inc. MT9123 Data Sheet PORT 1 PORT 2 PORT 2 Sin PORT 1 channel A Sin echo path A echo path A Rout + Adaptive Filter (64 ms) Adaptive Filter (128 ms) channel A Rout channel A Rin b) Extended Delay Configuration (128 ms) PORT 2 channel B + PORT 1 echo path Adaptive Filter (64 ms) channel B Sout + Sin echo path B Rin Optional -12dB pad E.C.A Optional -12dB pad E.C.A Sout - Sout + channel A Optional -12dB pad Adaptive Filter (64ms) Adaptive Filter (64 ms) + Rout E.C.B echo path Rin Optional -12dB pad E.C.A a) Normal Configuration (64 ms) Optional -12dB pad E.C.B c) Back-to-Back Configuration (64 ms) Figure 3 - Device Configuration Adaptive Filter The adaptive filter is a 1024 tap FIR filter which is divided into two sections. Each section contains 512 taps providing 64 ms of echo estimation. In Normal configuration, the first section is dedicated to channel A and the second section to channel B. In Extended Delay configuration, both sections are cascaded to provide 128 ms of echo estimation in channel A. Double-Talk Detector Double-Talk is defined as those periods of time when signal energy is present in both directions simultaneously. When this happens, it is necessary to disable the filter adaptation to prevent divergence of the adaptive filter coefficients. Note that when double-talk is detected, the adaptation process is halted but the echo canceller continues to cancel echo. A double-talk condition exists whenever the Sin signal level is greater than the expected return echo level. The relative signal levels of Rin (Lrin) and Sin (Lsin) are compared according to the following expression to identify a double-talk condition: Lsin > Lrin + 20log10(DTDT) where DTDT is the Double-Talk Detection Threshold. Lsin and Lrin are the relative signal levels expressed in dBm0. A different method is used when it is uncertain whether Sin consists of a low level double-talk signal or an echo return. During these periods, the adaptation process is slowed down but it is not halted. 6 Zarlink Semiconductor Inc. MT9123 Data Sheet Controllerless Mode In G.165 standard, the echo return loss is expected to be at least 6 dB. This implies that the Double-Talk Detector Threshold (DTDT) should be set to 0.5 (-6 dB). However, in order to get additional guardband, the DTDT is set internally to 0.5625 (-5 dB). In controllerless mode, the Double-Talk Detector is always active. Controller Mode In some applications the return loss can be higher or lower than 6 dB. The MT9123 allows the user to change the detection threshold to suit each application’s need. This threshold can be set by writing the desired threshold value into the DTDT register. The DTDT register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation: DTDT(hex) = hex(DTDT(dec) * 32768) where 0 < DTDT(dec) < 1 Example: For DTDT = 0.5625 (-5 dB), the hexadecimal value becomes hex(0.5625 * 32768) = 4800h Non-Linear Processor (NLP) After echo cancellation, there is always a small amount of residual echo which may still be audible. The MT9123 uses an NLP to remove residual echo signals which have a level lower than the Adaptive Suppression Threshold (TSUP in G.165). This threshold depends upon the level of the Rin (Lrin) reference signal as well as the programmed value of the Non-Linear Processor Threshold register (NLPTHR). TSUP can be calculated by the following equation: TSUP = Lrin + 20log10(NLPTHR) where NLPTHR is the Non-Linear Processor Threshold register value and Lrin is the relative power level expressed in dBm0. When the level of residual error signal falls below TSUP, the NLP is activated further attenuating the residual signal to less than -65 dBm0. To prevent a perceived decrease in background noise due to the activation of the NLP, a spectrally-shaped comfort noise, equivalent in power level to the background noise, is injected. This keeps the perceived noise level constant. Consequently, the user does not hear the activation and de-activation of the NLP. Controllerless Mode The NLP processor can be disabled by connecting the NLP pin to Vss. Controller Mode The NLP processor can be disabled by setting the NLPDis bit to 1 in Control Register 2. The NLPTHR register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation: NLPTHR(hex) = hex(NLPTHR(dec) * 32768) where 0 < NLPTHR(dec) < 1 The comfort noise injection can be disabled by setting the INJDis bit to 1 in Control Register 1. 7 Zarlink Semiconductor Inc. MT9123 Data Sheet It should be noted that the NLPTHR is valid and the comfort noise injection is active only when the NLP is enabled. Narrow Band Signal Detector (NBSD) Single or dual frequency tones (e.g., DTMF tones) present in the reference input (Rin) of the echo canceller for a prolonged period of time may cause the adaptive filter to diverge. The Narrow Band Signal Detector (NBSD) is designed to prevent this divergence by detecting single or dual tones of arbitrary frequency, phase, and amplitude. When narrow band signals are detected, the adaptation process is halted but the echo canceller continues to cancel echo. Controllerless Mode The NBSD is always active and automatically disables the filter adaptation process when narrow band signals are detected. Controller Mode The NBSD can be disabled by setting the NBDis bit to 1 in Control Register 2. Offset Null Filter Adaptive filters in general do not operate properly when a DC offset is present on either the reference signal (Rin) or the echo composite signal (Sin). To remove the DC component, the MT9123 incorporates Offset Null filters in both Rin and Sin inputs. Controllerless Mode The Offset Null filters are always active. Controller Mode The offset null filters can be disabled by setting the HPFDis bit to 1 in Control Register 2. Echo Canceller Functional States Each echo canceller has four functional states: Mute, Bypass, Disable Adaptation and Enable Adaptation. Mute: The Mute state forces the echo canceller to transmit quiet code and halts the filter adaptation process. In Normal configuration, the PCM output data on Rout is replaced with the quiet code according to the following table. LINEAR SIGN/ 16 bits MAGNITUDE 2’s µ-Law complement A-Law +Zero (quiet code) 0000h 80h CCITT (G.711) µ-Law A-Law FFh D5h Table 1 - Quiet PCM Code Assignment In Back-to-Back configuration, both echo cancellers are combined to implement a full duplex echo canceller. Therefore muting Echo Canceller A causes quiet code to be transmitted on Rout, while muting Echo Canceller B causes quiet code to be transmitted on Sout. 8 Zarlink Semiconductor Inc. MT9123 Data Sheet In Extended Delay configuration, both echo cancellers are cascaded to make one 128 ms echo canceller. In this configuration, muting Echo Canceller A causes quiet code to be transmitted on Rout. Bypass: The Bypass state directly transfers PCM codes from Rin to Rout and from Sin to Sout. When Bypass state is selected, the adaptive filter coefficients are reset to zero. Disable Adaptation: When the Disable Adaptation state is selected, the adaptive filter coefficients are frozen at their current value. In this state, the adaptation process is halted however the MT9123 continues to cancel echo. Enable Adaptation: In Enable Adaptation state, the adaptive filter coefficients are continually updated. This allows the echo canceller to model the echo return path characteristics in order to cancel echo. This is the normal operating state. Controllerless Mode The four functional states can be selected via S1, S2, S3, and S4 pins as shown in the following table. Echo Canceller A Functional State S2/S1 Echo Canceller B S4/S3 00 Mute(1) 00 01 Bypass(2) 01 10 Disable Adaptation(1,3) 10 11 Enable Adaptation(3) 11 Table 2 - Functional States Control Pins (1) Filter coefficients are frozen (adaptation disabled) (2) The adaptive filter coefficients are reset to zero (3) The MT9123 cancels echo Controller Mode The echo canceller functions are selected in Control Register 1 and Control Register 2 through four control bits: MuteS, MuteR, Bypass and AdaptDis. See Register Summary for details. MT9123 Throughput Delay The throughput delay of the MT9123 varies according to the data path and the device configuration. For all device configurations, except for Bypass state, Rin to Rout has a delay of two frames and Sin to Sout has a delay of three frames. In Bypass state, the Rin to Rout and Sin to Sout paths have a delay of two frames. In ST-BUS operation, the D and C channels have a delay of one frame. Power Down Forcing the PWRDN pin to logic low, will put the MT9123 into a power down state. In this state all internal clocks are halted, the DATA1, Sout and Rout pins are tristated and the F0od pin output high. The device will automatically begin the execution of its initialization routines when the PWRDN pin is returned to logic high and a clock is applied to the MCLK pin. The initialization routines execute for one frame and will set the MT9123 to default register values. 9 Zarlink Semiconductor Inc. MT9123 Data Sheet Device Configuration The MT9123 architecture contains two individually controlled echo cancellers (Echo Canceller A and B). They can be set in three distinct configurations: Normal, Back-to-Back, and Extended Delay. See Figure 3. Normal Configuration: In this configuration, the two echo cancellers (Echo Canceller A and B) are positioned in parallel, as shown in Figure 3a, providing 64 milliseconds of echo cancellation in two channels simultaneously. In SSI operation, both channels are available in different timeslots on the same TDM (Time Division Multiplexing) bus. For Echo Canceller A, the ENA1 enable strobe pin defines the Rin/Sout (PORT1) time slot while the ENA2 enable strobe pin defines the Sin/Rout (PORT2) time slot. The ENB1 and ENB2 enable strobes perform the same function for Echo Canceller B. In ST-BUS operation, the ENA1, ENA2, ENB1 and ENB2 pins are used to determine the PCM data format and the channel locations. See Table 4. Back-to-Back Configuration: In this configuration, the two echo cancellers are positioned to cancel echo coming from both directions in a single channel providing full duplex 64 millisecond echo-cancellation. See Figure 3c. This configuration uses only one timeslot on PORT1 and PORT2, allowing a no-glue interface for applications where bidirectional echo cancellation is required. In SSI operation, ENA1 and ENA2 enable pins are used to strobe data on Rin/Sout and Sin/Rout respectively. In ST-BUS operation, ENA1, ENA2, ENB1 and ENB2 inputs are used to select the ST-BUS mode according to Table 4. Examples of Back-to-Back configuration include positioning the MT9123 between a codec and a transmission device or between two codecs for echo control on analog trunks. Extended Delay configuration: In this configuration, the two echo cancellers are internally cascaded into one 128 millisecond echo canceller. See Figure 3b. In SSI operation, ENA1 and ENA2 enable pins are used to strobe data on Rin/Sout and Sin/Rout respectively. In ST-BUS operation, ENA1, ENA2, ENB1 and ENB2 inputs are used to select the ST-BUS mode according to Table 4. Controllerless Mode The three configurations can be selected through the CONFIG1 and CONFIG2 pins as shown in the following table. CONFIG1 CONFIG2 CONFIGURATION 0 0 (selects Controller Mode) 0 1 Extended Delay Mode 1 0 Back-to-Back Mode 1 1 Normal Mode Table 3 - Configuration in Controllerless Mode Controller Mode In Control Register 1, the Normal configuration can be programmed by setting both BBM and Extended-Delay bits to 0. Back-to-Back configuration can be programmed by setting the BBM bit to 1 and Extended-Delay bit to 0. 10 Zarlink Semiconductor Inc. MT9123 Data Sheet Extended-Delay configuration can be programmed by setting the Extended-Delay bit to 1 and BBM bit to 0. Both BBM and Extended-Delay bits in Control Register 1 can not be set to 1 at the same time. PCM Data I/O The PCM data transfer for the MT9123 is provided through two PCM ports. PORT1 consists of Rin and Sout pins while PORT2 consists of Sin and Rout Pins. The Data is transferred through these ports according to either STBUS or SSI conventions. The device determines the mode of operation by monitoring the signal applied to the F0i pin. When a valid ST-BUS frame pulse is applied to the F0i pin, the MT9123 will assume ST-BUS operation. If F0i is tied continuously to Vss the MT9123 will assume SSI operation. ST-BUS Operation The ST-BUS PCM interface conforms to Zarlink’s ST-BUS standard and it is used to transport 8 bit companded PCM data (using one timeslot) or 16 bit 2’s complement linear PCM data (using two timeslots). Pins ENA1 and ENB1 select timeslots on PORT1 while pins ENA2 and ENB2 select timeslots on PORT2. See Table 4 and Figures 5 to 8. PORT1 Rin/Sout ST-BUS Mode Selection PORT2 Sin/Rout Enable Pins Enable Pins ENB1 ENA1 ENB2 ENA2 0 0 Mode 1. 8 bit companded PCM I/O on timeslots 0 & 1. 0 0 0 1 Mode 2. 8 bit companded PCM I/O on timeslots 2 & 3. 0 1 1 0 Mode 3. 8 bit companded PCM I/O on timeslots 2 & 3. Includes D & C channel bypass in timeslots 0 & 1. 1 0 1 1 Mode 4. 16 bit 2’s complement linear PCM I/O on timeslots 0 - 3. 1 1 Table 4 - ST-BUS Mode Select Note that if the device is in back-to-back or extended delay configurations, the second timeslot in any ST-BUS Mode contains undefined data. This means that the following timeslots contain undefined data: timeslot 1 in STBUS Mode 1; timeslot 3 in ST-BUS Modes 2 & 3 and timeslots 2 and 3 in ST-BUS Mode 4. SSI Operation The SSI PCM interface consists of data input pins (Rin, Sin), data output pins (Sout, Rout), a variable rate bit clock (BCLK), and four enable pins (ENA1,ENB1, ENA2 and ENB2) to provide strobes for data transfers. The active high enable may be either 8 or 16 BCLK cycles in duration. Automatic detection of the data type (8 bit companded or 16 bit 2’s complement linear) is accomplished internally. The data type cannot change dynamically from one frame to the next. In SSI operation, the frame boundary is determined by the rising edge of the ENA1 enable strobe (see Figure 9). The other enable strobes (ENB1, ENA2 and ENB2) are used for parsing input/output data and they must pulse within 125 microseconds of the rising edge of ENA1. If they are unused, they must be tied to Vss. In SSI operation, the enable strobes may be a mixed combination of 8 or 16 BCLK cycles allowing the flexibility to mix 2’s complement linear data on one port (e.g., Rin/Sout) with companded data on the other port (e.g., Sin/Rout). 11 Zarlink Semiconductor Inc. MT9123 Data Sheet Enable Strobe Pin Echo Canceller Port ENA1 A 1 ENB1 B 1 ENA2 A 2 ENB2 B 2 Table 5 - SSI Enable Strobe Pins PCM Law and Format Control (LAW, FORMAT) The PCM companding/coding law used by the MT9123 is controlled through the LAW and FORMAT pins. ITU-T G.711 companding curves for µ-Law and A-Law are selected by the LAW pin. PCM coding ITU-T G.711 and SignMagnitude are selected by the FORMAT pin. See Table 6. Sign-Magnitude ITU-T (G.711) FORMAT=0 FORMAT=1 PCM Code µ/A-LAW µ-LAW A-LAW LAW = 0 or 1 LAW = 0 LAW =1 + Full Scale 1111 1111 1000 0000 1010 1010 + Zero 1000 0000 1111 1111 1101 0101 - Zero 0000 0000 0111 1111 0101 0101 - Full Scale 0111 1111 0000 0000 0010 1010 Table 6 - Companded PCM Linear PCM The 16-bit 2’s complement PCM linear coding permits a dynamic range beyond that which is specified in ITU-T G.711 for companded PCM. The echo-cancellation algorithm will accept 16 bits 2’s complement linear code which gives a dynamic range of +15 dBm0. Linear PCM data must be formatted as 14-bit, 2’s complement data with three bits of sign extension in the most significant positions (i.e.: S,S,S,12,11, ...1,0) for a total of 16 bits where “S” is the extended sign bit. When A-Law is converted to 2’s complement linear format, it must be scaled up by 6 dB (i.e., left shifted one bit) with a zero inserted into the least significant bit position. See Figure 7. Bit Clock (BCLK/C4i) The BCLK/C4i pin is used to clock the PCM data in both SSI (BCLK) and ST-BUS (C4i) operations. In SSI operation, the bit rate is determined by the BCLK frequency. This input must contain either eight or sixteen clock cycles within the valid enable strobe window. BCLK may be any rate between 128 KHz to 4.096 MHz and can be discontinuous outside of the enable strobe windows defined by ENA1, ENB1, ENA2 and ENB2 pins. Incoming PCM data (Rin, Sin) are sampled on the falling edge of BCLK while outgoing PCM data (Sout, Rout) are clocked out on the rising edge of BCLK. See Figure 17. In ST-BUS operation, connect the system C4 (4.096 MHz) clock to the C4i pin. 12 Zarlink Semiconductor Inc. MT9123 Data Sheet Master Clock (MCLK) A nominal 20 MHz master clock (MCLK) is required for execution of the MT9123 algorithms. The MCLK input may be asynchronous with the 8 KHz frame. If only one channel operation is required, (Echo Canceller A only) the MCLK can be as low as 9.6 MHz. Microport The serial microport provides access to all MT9123 internal read and write registers and it is enabled when CONFIG1 and CONFIG2 pins are both set to logic 0. This microport is compatible with Intel MCS-51 (mode 0), Motorola SPI (CPOL=0, CPHA=0), and National Semiconductor Microwire specifications. The microport consists of a transmit/receive data pin (DATA1), a receive data pin (DATA2), a chip select pin (CS) and a synchronous data clock pin (SCLK). The MT9123 automatically adjusts its internal timing and pin configuration to conform to Intel or Motorola/National requirements. The microport dynamically senses the state of the SCLK pin each time CS pin becomes active (i.e., high to low transition). If SCLK pin is high during CS activation, then Intel mode 0 timing is assumed. In this case DATA1 pin is defined as a bi-directional (transmit/receive) serial port and DATA2 is internally disconnected. If SCLK is low during CS activation, then Motorola/National timing is assumed and DATA1 is defined as the data transmit pin while DATA2 becomes the data receive pin. The MT9123 supports Motorola half-duplex processor mode (CPOL=0 and CPHA=0). This means that during a write to the MT9123, by the Motorola processor, output data from the DATA1 pin must be ignored. This also means that input data on the DATA2 pin is ignored by the MT9123 during a valid read by the Motorola processor. All data transfers through the microport are two bytes long. This requires the transmission of a Command/Address byte followed by the data byte to be written or read from the addressed register. CS must remain low for the duration of this two-byte transfer. As shown in Figures 9 and 10, the falling edge of CS indicates to the MT9123 that a microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used to receive the Command/Address byte from the microcontroller. The Command/Address byte contains information detailing whether the second byte transfer will be a read or a write operation and at what address. The next 8 clock cycles are used to transfer the data byte between the MT9123 and the microcontroller. At the end of the two-byte transfer, CS is brought high again to terminate the session. The rising edge of CS will tri-state the DATA1 pin. The DATA1 pin will remain tri-stated as long as CS is high. Intel processors utilize Least Significant Bit (LSB) first transmission while Motorola/National processors use Most Significant Bit (MSB) first transmission. The MT9123 microport automatically accommodates these two schemes for normal data bytes. However, to ensure timely decoding of the R/W and address information, the Command/Address byte is defined differently for Intel and Motorola/National operations. Refer to the relative timing diagrams of Figures 9 and 10. Receive data is sampled on the rising edge of SCLK while transmit data is clocked out on the falling edge of SCLK. Detailed microport timing is shown in Figure 18 and Figure 19. 13 Zarlink Semiconductor Inc. MT9123 Function Data Sheet Controllerless Controller selected when pins CONFIG1 & 2 ≠ 00 selected when pins CONFIG1 & 2 = 00 Normal Configuration Set pins CONFIG1 to 1 and CONFIG2 1 to select this configuration. Set bits Extended-Delay to 0 and BBM to 0 in Control Register 1 to select. Back-to-Back Configuration Set pins CONFIG1 to 1 and CONFIG2 to 0 to select this configuration. Set bit BBM to 1 in Control Register 1 to select. Extended Delay Configuration Set pins CONFIG1 to 0 and CONFIG2 to 1 to select this configuration. Set bit Extended-Delay to 1 in Control Register 1 to select. Mute Set pins S2/S1 to 00 and S4/S3 to 00 to select for Echo Set bit MuteR to 1 or MuteS to 1 in Control Register 2 to Canceller A and Echo Canceller B respectively. select. Bypass Set pins S2/S1 to 01 and S4/S3 to 01 to select for Echo Set bit Bypass to 1 in Control Register 1 to select. Canceller A and Echo Canceller B, respectively. Disable Adaptation Set pins S2/S1 to 10 and S4/S3 to 10 to select for Echo Set bit AdaptDis to 1 in Control Register 1 to select. Canceller A and Echo Canceller B, respectively. Enable Adaptation Set pins S2/S1 to 11 and S4/S3 to 11 to select for Echo Set bits AdaptDis to 0 and Bypass to 0 in Control Register Canceller A and Echo Canceller B, respectively. 1 to select. SSI Tie pin F0i to VSS to select. Tie pin F0i to VSS to select. ST-BUS Apply a valid ST-BUS frame pulse to F0i pin to select. Apply a valid ST-BUS frame pulse to F0i pin to select. 12dB Attenuator Always disabled. Set bit PAD to 1 in Control Register 1 to enable. Double-Talk Detector Continuously enabled which disables filter adaptation when double-talk is detected. The detection threshold can be controlled via Double-Talk Detection Threshold Register 1 and 2. Non-Linear Processor Set pin NLP to 1 to enable. Set bit NLPDis to 1 to disable. PCM Law Set pin LAW to 1 or 0 to select A-Law or µ-Law respectively. Set pin LAW to 1or 0 to select A-Law or µ-Law respectively. PCM Format Set pin FORMAT to 0 or 1 to select Sign-Magnitude or ITU-T format respectively. Set pin FORMAT to 0 or 1 to select Sign-Magnitude or ITU-T format respectively. Narrow-Band Signal Detector Continuously enabled which disables the filter adaptation when narrow band signal is detected. Set bit NBDis to 1 in Control Register 2 to disable. Offset Null Filter Continuously enabled which removes the DC component in the PCM input. Set bit HPFDis to 1 in Control Register 2 to disable. Table 7 - MT9123 Function Control Summary 14 Zarlink Semiconductor Inc. MT9123 Data Sheet C4i F0i 0 1 2 ECA ECB 3 4 F0od PORT1 Rin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Sout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 ECB ECA PORT2 Sin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Rout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 outputs=High impedance inputs = don’t care In ST-BUS Mode 1, both echo canceller I/O channels are assigned to ST-BUS timeslots 0 and 1. Note that the user could configure PORT1 and PORT2 into different ST-BUS modes. The pin F0od is always delayed 4 time slots to permit a more flexible interleave of ST-BUS modes. Figure 4 - ST-BUS 8 Bit Companded PCM I/O on Timeslots 0 & 1 (Mode 1) C4i F0i 0 1 2 3 4 F0od PORT1 ECA ECB Rin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Sout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 PORT2 ECA ECB Sin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Rout 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 outputs=High impedance inputs = don’t care In ST-BUS Mode 2, both echo canceller I/O channels are assigned to ST-BUS timeslots 2 and 3. Note that the user could configure PORT1 and PORT2 into different ST-BUS modes. The pin F0od is always delayed 4 time slots to permit a more flexible interleave of ST-BUS modes. Figure 5 - ST-BUS 8 Bit Companded PCM I/O on Timeslots 2 & 3 (Mode 2) 15 Zarlink Semiconductor Inc. MT9123 Data Sheet C4i F0i 0 1 2 3 4 F0od PORT1 Rin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 ECA Sout ECB 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 PORT2 Sin 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 ECA Rout ECB 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 outputs=High impedance inputs = don’t care indicates that an input channel is bypassed to an output channel ST-BUS Mode 3 supports connection to 2B+D devices where timeslots 0 and 1 transport D and C channels and both echo canceller I/O channels are assigned to ST-BUS timeslots 2 and 3. Both PORT1 and PORT2 must be configured in ST-BUS Mode 3. Figure 6 - ST-BUS 8 Bit Companded PCM I/O with D and C channels (Mode 3) C4i F0i F0od Rin S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 PORT1 ECA ECB Sout S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 Sin S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 PORT2 Rout ECB ECA S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 S S S 12 11 10 9 8 7 6 5 4 3 2 1 0 outputs=High impedance inputs = don’t care ST-BUS Mode 4 allows 16 bits 2’s complement linear data to be transferred using ST-BUS I/O timing. Note that PORT1 and PORT2 need not necessarily both be in mode 4. Figure 7 - ST-BUS 16 Bit 2’s Complement Linear PCM I/O (Mode 4) 16 Zarlink Semiconductor Inc. MT9123 Data Sheet BCLK PORT1 ECA ECB ENA1 ENB1 Rin Sout PORT2 8 or 16 bits 8 or 16 bits 8 or 16 bits 8 or 16 bits ECA ECB ENA2 ENB2 Sin Rout 8 or 16 bits 8 or 16 bits 8 or 16 bits 8 or 16 bits outputs=High impedance inputs = don’t care Note that the two ports are independent so that, for example, PORT1 can operate with 8 bit enable strobes and PORT2 can operate with 16 bit enable strobes. Figure 8 - SSI Operation 17 Zarlink Semiconductor Inc. MT9123 COMMAND/ADDRESS ✕ DATA 1 R/W A0 A1 A2 A3 A4 A5 Data Sheet DATA INPUT/OUTPUT ✑ D0 D1 D2 D3 D4 D5 D6 D7 X SCLK ✒ CS ✔ ✓ ✑ ✒ Delays due to internal processor timing which are transparent to the MT9123. The MT9123: latches receive data on the rising edge of SCLK outputs transmit data on the falling edge of SCLK ✓ The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent byte is always data followed by CS returning high. ✔ A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again. ✕ The COMMAND/ADDRESS byte contains: 1 bit - Read/Write 6 bits - Addressing Data 1 bit - Unused Figure 9 - Serial Microport Timing for Intel Mode 0 COMMAND/ADDRESS ✕ DATA 2 Receive R/W A5 A4 A3 A2 A1 A0 ✑ X DATA INPUT D7 D6 D5 D4 D3 D2 D1 D0 DATA OUTPUT DATA 1 Transmit High Impedance D7 D6 D5 D4 D3 D2 D1 D0 SCLK ✒ CS ✔ ✓ ✑ Delays due to internal processor timing which are transparent to the MT9123. ✒ The MT9123: ✓ The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent byte is always data followed by CS returning high. latches receive data on the rising edge of SCLK outputs transmit data on the falling edge of SCLK ✔ A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again. ✕ The COMMAND/ADDRESS byte contains: 1 bit - Read/Write 6 bits - Addressing Data 1 bit - Unused Figure 10 - Serial Microport Timing for Motorola Mode 00 or National Microwire 18 Zarlink Semiconductor Inc. MT9123 Data Sheet Register Summary Echo Canceller A, Control Register 1 CRA1 Reset 7 INJDis 6 BBM PAD 5 4 ADDRESS = 00h WRITE/READ VERIFY Bypass AdaptDis 3 2 0 Extended Delay 1 0 Echo Canceller B, Control Register 1 CRB1 Reset 7 ExtendedDelay INJDis 6 BBM PAD 5 4 Power Reset Value 0000 0000 ADDRESS = 20h WRITE/READ VERIFY Bypass AdaptDis 3 2 1 0 1 0 Power Reset Value 0000 0010 When high, Echo Cancellers A and B are internally cascaded into one 128ms echo canceller. When low, Echo Cancellers A and B operate independently. Do not enable both Extended-Delay and BBM configurations at the same time. AdaptDis When high, echo canceller adaptation is disabled. When low, the echo canceller dynamically adapts to the echo path characteristics. Bypass When high, Sin data is by-passed to Sout and Rin data is by-passed to Rout. When low, output data on both Sout and Rout is a function of the echo canceller algorithm. PAD When high, 12 dB of attenuation is inserted into the Rin to Rout path. When low the Rin to Rout path gain is 0 dB. BBM When high the Back to Back configuration is enabled. When low the Normal configuration is enabled. Do not enable Extended-Delay and BBM configurations at the same time. Always set both BBM bits of the two echo cancellers to the same logic value to avoid conflict. INJDis When high, the noise injection process is disabled. When low noise injection is enabled. Reset When high, the power-up initialization is executed presetting all register bits including this bit. Note: Bits marked as “1” or “0” are reserved bits and should be written as indicated. Echo Canceller A, Control Register 2 Echo Canceller B, Control Register 2 CR2 0 0 7 6 NLPDis 5 0 4 ADDRESS = 01h WRITE/READ VERIFY ADDRESS = 21h WRITE/READ VERIFY NBDis 3 HPFDis MuteS MuteR 2 1 0 MuteR When high, data on Rout is muted to quiet code. When low, Rout carries active code. MuteS When high, data on Sout is muted to quiet code. When low, Sout carries active code. HPFDis When high, the offset nulling high pass filters are bypassed in the Rin and Sin paths. When low, the offset nulling filters are active and will remove DC offsets on PCM input signals. NBDis When high, the narrow-band detector is disabled. When low, the narrow-band detector is enabled. NLPDis When high, the non-linear processor is disabled. When low, the non-linear processors function normally. Useful for G.165 conformance testing. Note: Bits marked as “0” are reserved bits and should be written as indicated. 19 Zarlink Semiconductor Inc. Power Reset Value 0000 0000 MT9123 Data Sheet Echo Canceller A, Status Register Echo Canceller B, Status Register SR DTDet 7 6 5 ADDRESS = 02h READ ADDRESS = 22h READ Conv Down Active 4 3 2 NB 1 Power Reset Value 0000 0000 0 NB Logic high indicates the presence of a narrow-band signal on Rin. Active Logic high indicates that the power level on Rin is above the threshold level (i.e., low power condition). Down Decision indicator for the non-linear processor gain adjustment. Conv Decision indicator for rapid adaptation convergence. Logic high indicates a rapid convergence state. DTDet Logic high indicates the presence of a double-talk condition. 20 Zarlink Semiconductor Inc. MT9123 Data Sheet Echo Canceller A, Flat Delay Register Echo Canceller B, Flat Delay Register FD ADDRESS = 04h WRITE/READ VERIFY ADDRESS = 24h WRITE/READ VERIFY FD7 FD6 FD5 FD4 FD3 FD2 FD1 FD0 7 6 5 4 3 2 1 0 Echo Canceller A, Decay Step Number Register Echo Canceller B, Decay Step Number Register NS ADDRESS = 07h WRITE/READ VERIFY ADDRESS = 27h WRITE/READ VERIFY NS7 NS6 NS5 NS4 NS3 NS2 NS1 NS0 7 6 5 4 3 2 1 0 Echo Canceller A, Decay Step Size Control Register Echo Canceller B, Decay Step Size Control Register SSC Power Reset Value 00h 0 0 0 0 0 SSC2 7 6 5 4 3 2 Power Reset Value 00h ADDRESS = 06h WRITE/READ VERIFY ADDRESS = 26h WRITE/READ VERIFY SSC1 1 SSC0 Power Reset Value 04h 0 Note: Bits marked with “0” are reserved bits and should be written “0”. Amplitude of MU FIR Filter Length (512 or 1024 taps) 1.0 Step Size (SS) Flat Delay (FD7-0) 2-16 Time The Exponential Decay registers (Decay Step Number and Decay Step Size) and Flat Delay register the(NS LMS adaptation Number allow of Steps 7-0) step-size (MU) to be programmed over the length of the FIR filter. A programmable MU profile allows the performance of the echo canceller to be optimized for specific applications. For example, if the characteristic of the echo response is known to have a flat delay of several milliseconds and a roughly exponential decay of the echo impulse response, then the MU profile can be programmed to approximate this expected impulse response thereby improving the convergence characteristics of the adaptive filter. Note that in the following register descriptions, one tap is equivalent to 125 µs (64 ms/512 taps). FD7-0 Flat Delay: This register defines the flat delay of the MU profile, (i.e., where the MU value is 2-16). The delay is defined as FD7-0 x 8 taps. For example; if FD7-0 = 5, then MU=2-16 for the first 40 taps of the echo canceller FIR filter. The valid range of FD7-0 is: 0