MSAU213

MSAU200 Series 1W, Miniature SMD, Dual Output DC/DC Converters Key Features Efficiency up to 80% 1000VDC Isolation MTBF > 2,000,000 Hours Low Cost Input 5 and 12VDC Output {5, {9, {12 and {15VDC Temperature Performance -40] to +85] Lead Frame Technology UL 94V-0 Package Material Interanl SMD Construction Minmax's MSAU200 1W DC/DC's are in "gull-wing" SMT package, weigh a mere 1.8 grams and meet 245]/10sec in solder-reflow for lead free process. The series consists of 8 models with input voltages of 5V and 12VDC which offers standard dual output voltages of {5V, {9V, {12V and {15VDC for the choice. Their impressive guaranteed efficiencies enable all models to deliver their fully rated output power from -40] to +85] without heat sinking or forced-air cooling. The MSAU200 series is an excellent selection for a variety of applications including data communication equipments, distributed power systems, telecommunication equipments, and industrial robot systems. The MSAU200 units are available in tape and reel package. I/O Isolation SMD 1000 VDC $ Low Cost Low Profile Block Diagram +Vo +Vin Bipolar Push-Pull Inverter -Vin -Vo Com. 1 MINMAX REV:0 2005/04 MSAU200 Series Model Selection Guide Model Number Input Voltage Output Voltage Output Current Input Current Load Regulation Efficiency VDC MSAU201 MSAU202 MSAU203 MSAU204 MSAU211 MSAU212 MSAU213 MSAU214 12 ( 10.8 ~ 13.2 ) 5 ( 4.5 ~ 5.5 ) VDC {5 {9 {12 {15 {5 {9 {12 {15 Max. mA {100 {55 {42 {33 {100 {55 {42 {33 Min. mA {2 {1 {0.8 {0.7 {2 {1 {0.8 {0.7 @Max. Load mA (Typ.) 267 260 255 251 111 109 105 103 @No Load mA (Typ.) % (Max.) 10 10 8 7 8 8 5 5 @Max. Load % (Typ.) 75 76 79 79 75 76 80 80 30 15 Absolute Maximum Ratings Parameter Input Surge Voltage ( 1000 mS ) Internal Power Dissipation 5VDC Input Models 12VDC Input Models Min. -0.7 -0.7 ----Max. 9 18 260 450 Unit VDC VDC ] mW Notes : 1. Specifications typical at Ta=+25], resistive load, nominal input voltage, rated output current unless otherwise noted. 2. Ripple & Noise measurement bandwidth is 0-20 MHz. 3. These power converters require a minimum output loading to maintain specified regulation. 4. Operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. Lead Temperature (1.5mm from case for 10 Sec.) Exceeding the absolute maximum ratings of the unit could cause damage. These are not continuous operating ratings. Environmental Specifications Parameter Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Conditions Ambient Case Min. -40 -40 -40 --Free-Air Convection Max. +85 +90 +125 95 Unit ] ] ] % 5. All DC/DC converters should be externally fused at the front end for protection. 6. Other input and output voltage may be available, please contact factory. 7. Specifications subject to change without notice. Input Specifications Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Model 5V Input Models 12V Input Models All Models Min. 4.5 10.8 --Typ. 5 12 --Max. 5.5 13.2 0.3 Unit VDC A Internal Capacitor REV:0 2005/04 MINMAX 2 MSAU200 Series Output Specifications Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Over Load Temperature Coefficient Output Short Circuit Over Line, Load & Temp. Dual Output, Balanced Loads For Vin Change of 1% Io=20% to 100% Conditions Min. ------------120 --0.5 Second Max. Typ. {1.0 {0.1 {1.2 60 ------{0.01 Max. {3.0 {1.0 {1.5 120 150 5 --{0.02 Unit % % % % mV P-P mV P-P mV rms % %/] See Model Selection Guide General Specifications Parameter Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Isolation Capacitance Switching Frequency MTBF MIL-HDBK-217F @ 25], Ground Benign Conditions 60 Seconds Flash Tested for 1 Second 500VDC 100KHz,1V Min. 1000 1100 1000 --50 2000 Typ. ------40 100 --Max. ------100 140 --Unit VDC VDC M[ pF KHz K Hours Capacitive Load Models by Vout Maximum Capacitive Load # For each output {5V # 33 {9V # 33 {12V # 33 {15V # 33 Unit uF Input Fuse Selection Guide 5V Input Models 500mA Slow - Blow Type 12V Input Models 200mA Slow - Blow Type 3 MINMAX REV:0 2005/04 MSAU200 Series 90 80 Efficiency (%) 70 60 50 40 60 50 100 90 Efficiency (%) 80 70 30 Low Nom Input Voltage (V) High 20 10 20 40 60 80 100 Load Current (%) Efficiency vs Input Voltage Efficiency vs Output Load 100 80 Output Power (%) 100LFM 400LFM 200LFM 60 Natural convection 40 20 0 -40 〜 50 60 70 80 ] 90 100 110 Ambient Temperature Derating Curve REV:0 2005/04 MINMAX 4 MSAU200 Series Test Configurations Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0[ at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + Battery + Lin Current Probe + DC Power Source + Cin -Vin -Out +Vin DC / DC Converter +Out Load KHz) capacitor of 2.2uF for the 5V input devices, and a 1.0uF for the 12V devices. +Vin +Out Load Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 0.47uF capacitors at the output. + DC Power Source -Vin +Vin +Out Dual Output DC / DC Com. Converter -Out Cout Load DC / DC Converter -Vin -Out Cin Peak-to-Peak Output Noise Measurement Test Use a Cout 0.33uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin Dual Output DC / DC Converter -Vin +Out Com. Cout -Out Scope Copper Strip Cout Scope Resistive Load Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90°C. The derating curves are determined from measurements obtained in an experimental apparatus. Design & Feature Considerations Maximum Capacitive Load The MSAU200 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. For optimum performance we recommend 33uF maximum capacitive load. The maximum capacitance can be found in the data sheet. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0[ at 100 5 MINMAX REV:0 2005/04 MSAU200 Series Mechanical Data 0.3[0.01] Connecting Pin Patterns Top View ( 2.54 mm / 0.1 inch grids ) 15.24 [0.60] 8.0 [0.31] 10 9 8 7 6 ] .02 R0 .5[ R0 10.16mm 4 1.7mm 0.9[0.04] + 1 2 3 4 5 [Magnification of A] 6.2 [0.24] 1C 10.8mm 0.60 [0.024] 2.0 [0.08] A 2.54mm 1.0mm Min 6.8 [0.27] S SEATING PLANE 0.3 [0.01] 2.54 [0.100] 10.2 [0.40] 7.0 [0.28] 11.2 [0.44] Tolerance Millimeters X.X{0.25 X.XX{0.13 Inches X.XX{0.01 X.XXX{0.005 {0.002 Pin {0.05 Pin Connections Pin 1 2 3 4 5 6 7 8 9 10 Function -Vin +Vin NA Common -Vout NA +Vout NA NA NA NA : Not Available for Electrical Connection +4 9.2 [0.36] Physical Characteristics Case Size : 15.24*8.0*6.8 mm 0.60*0.31*0.27 inches Molding 1.8g UL94V-0 Case Material Weight Flammability : : : The MSAU200 converter is encapsulated in a low thermal resistance molding compound that has excellent resistance/electrical characteristics over a wide temperature range or in high humidity environments. The encapsulant and unit case are both rated to UL 94V-0 flammability specifications. Leads are tin plated for improved solderability. REV:0 2005/04 MINMAX 6 MSAU200 Series Packaging Specifications 30.4 Max 2.0+1 / -0 0 330.0 Max 0 100.0 Min 0 13.00± 0.25 All dimentions in mm Tape Sprocket hole 0 1.55 +0.1 / -0 4.00 2.00 Sprocket hole tolerance over any 10 pitches ± 0.2 11.50 1.75 15.75 24.00± 0.3 All dimentions in mm XX.XX± 0.1 0 1.50 +0.25 / -0 Direction of Unreeling 11.60 16.00 0.4 +/- 0.05 7.20 0.30 7 MINMAX REV:0 2005/04 MSAU200 Series Tube 14.5 7.2 7.3 8.6 10.4 0.5 +/- 0.1 Tube material: PVC 4.5 5.0 All dimensions in mm, +/- 0.25mm 410 +/-1.5 Packaging Details Packaging Style Tube Tape and Reel to IEC 286-3 Specifications Quantity 25 500 REV:0 2005/04 MINMAX 8