MM1116

MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch Monolithic IC MM1111~MM1118 Outline These ICs are video switches for video / audio signal switching, with 2-input 1-output or 3-input 1-output. The series includes those with and without built-in clamp and 6dB amp circuits. Circuit configuration tables and block diagrams are as follows. MM1118 is used as the representative model in this description. MM1111~MM1118 Series Circuit Configuration Table Model name MM1111 MM1112 MM1113 MM1114 MM1115 MM1116 MM1117 MM1118 # of Inputs 2 2 3 3 2 2 3 3 # of Outputs 1 1 1 1 1 1 1 1 6dB amplifier No Yes No Yes No Yes No Yes Clamp circuit No No No No Yes Yes Yes Yes Power supply voltage 4.6~13.0V 8.0~13.0V 4.6~13.0V 8.0~13.0V 4.6~13.0V 4.6~13.0V 4.6~13.0V 4.6~13.0V MM1111~MM1118 Input/Output Voltage Measurement Values (typ.) Model name Input / Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage Input voltage Output voltage 1.35 0.59 1.29 1.06 1.35 0.59 1.29 1.06 2.77 2.01 Power supply voltage 5V 2.77 2.01 9V 5.02 4.26 4.06 4.30 5.02 4.26 4.06 4.30 2.40 1.65 2.30 1.76 2.40 1.65 2.30 1.76 12V 6.71 5.96 5.45 5.57 6.71 5.96 5.45 5.57 3.20 2.45 3.05 2.30 3.20 2.45 3.05 2.30 Unit V V V V V V V V V V V V V V V V MM1111 MM1112 MM1113 MM1114 MM1115 MM1116 MM1117 MM1118 MITSUMI MM1111 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Control input truth table SW L H OUT IN1 IN2 MM1112 Control input truth table SW L H OUT IN1 IN2 MITSUMI MM1113 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Control input truth table SW1 L H SW2 L L H OUT IN1 IN2 IN3 MM1114 Control input truth table SW1 L H SW2 L L H OUT IN1 IN2 IN3 MITSUMI MM1115 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Control input truth table SW L H OUT IN1 IN2 MM1116 Control input truth table SW L H OUT IN1 IN2 MITSUMI MM1117 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Control input truth table SW1 L H SW2 L L H OUT IN1 IN2 IN3 MM1118 Control input truth table SW1 L H SW2 L L H OUT IN1 IN2 IN3 MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Introduction of Main Model 3-Input 1-Output Video Switch (with 6dB amp) Monolithic IC MM1118 Outline This is a 3-input, 1-output video switch IC with a clamp function and built-in 6dB amp, for video signal switching. One of the inputs also has a mute function. Features 1. Built-in 6dB amp 2. Clamp function 3. Mute function 4. Current consumption 5. Operating power supply voltage range 6. Frequency response 7. Crosstalk 5.1mA typ. 4.6~13.0V 10MHz 64dB (at 4.43MHz) Package SOP-8C (MM1118XF) SIP-8A (MM1118XS) Applications 1. TV 2. VCR 3. Other video equipment MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Pin Description Pin no. SOP-8C 1 3 5 SIP-8A 5 7 1 Pin name IN1 IN2 IN3 Function Input 1 Input 2 Input 3 Internal equivalent circuit diagram 2 4 6 8 SW1 SW2 Switch 1 Switch 2 6 7 2 3 VCC OUT Power supply Output 8 4 GND Ground MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Absolute Maximum Ratings Item Storage temperature Operating temperature Power supply voltage Allowable loss (Ta=25°C) Symbol TSTG TOPR VCC Pd Ratings -40~+125 -20~+75 15 300 (SOP-8C) 1000 (SIP-8A) Units °C °C V mW Electrical Characteristics Item (Except where noted otherwise, Ta=25°C, VCC=5.0V) Symbol VCC Id Gv FC DG DP Voff CT VIH1 VIL1 VIH2 VIL2 Ro Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit Refer to Measuring Circuit 25 2.1 0.7 2.1 0.7 -64 5.5 -1 Measurement conditions Min. Typ. Max. Units 4.6 5.1 6.0 0 0 0 13.0 6.6 6.5 +1 ±3 ±3 ±30 -54 V mA dB dB % deg mV dB V V V V Ω Operating power supply voltage range Consumption current Voltage gain Frequency characteristic Differential gain Differential phase Output offset voltage Crosstalk Switch 1 input voltage H Switch 1 input voltage L Switch 2 input voltage H Switch 2 input voltage L Output impedance MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Measuring Procedures Item Consumption current Voltage gain Symbol Id GV (Except where noted otherwise, VCC=5.0V, VC1=VCC, VC2=0V) Switch state S2 S3 S4 2 2 2 2 1 2 2 2 1 2 2 2 1 2 2 2 1 2 2 2 2 2 2 2 2 1 1 1 2 2 2 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 1 2 2 2 2 2 2 2 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 1 1 2 1 2 2 1 2 1 1 Measuring Procedure Connect a DC ammeter to the VCC pin and measure. The ammeter is shorted for use in subsequent measurements. Input a 1.0VP-P, 100kHz sine wave to SG, and obtain GV from the following formula given TP1 voltage as V1 and TP3 voltage as V2. GV=20LOG (V2/V1) dB For the above GV measurement, given TP3 voltage for 10MHz as V3, FC is obtained from the following formula. FC=20LOG (V3/V2) dB Input a 1.0VP-P staircase wave to SG, and measure differential gain at TP3. APL=10~90% Proceed as for DG, and measure differential phase. Measure the DC voltage difference of each switch status at TP2. Assume VC1=2.1V, VC2=0.7V. Input a 2.0VP-P, 4.43MHz sine wave to SG, and given TP1 voltage as V4 and TP3 voltage as V5, CT is obtained from the following formula. CT = 20LOG (V5/V4) dB Impress an optional DC voltage on TP6 and TP7. Gradually raise from VC1=0V. TP4 voltage when TP7 voltage is output on TP2 is VIH1. Gradually lower from VC1=VCC. TP4 voltage when TP6 voltage is output on TP2 is VIL1. Impress an optional DC voltage on TP6 and TP8. Gradually raise from VC1=0V. TP5 voltage when TP8 voltage is output on TP2 is VIH2. Gradually lower from VC1=VCC. TP5 voltage when TP6 voltage is output on TP2 is VIL2. S1 2 1 2 2 2 1 2 2 2 1 2 2 2 1 2 2 2 2 2 2 1 1 1 2 2 2 2 2 2 S5 2 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 1 2 2 1 2 1 1 2 1 1 2 2 2 Frequency characteristic FC Differential gain DG Differential phase DP Output offset voltage Voff Crosstalk CT Switch 1 input voltage H Switch 1 input voltage L Switch 2 input voltage H Switch 2 input voltage L VIH1 VIL1 2 VIH2 VIL2 2 2 2 1 MITSUMI 2-Input 1-Output Video Switch / 3-Input 1-Output Video Switch MM1111~MM1118 Measuring Circuit