0430300004-04-N6

12 11 WIRE SIZE H MAX INSULATION .073/1.85 20-24 26-30 18 OR 0.75mm² 10 "D" "E" "G" "H" ±.012 ±0.30 ±.012 ±0.30 ±.005 ±0.13 ±.012 ±0.30 ±.005 ±0.13 ±.012 ±0.30 .099/2.51 .083/2.10 .099/2.51 .025/0.64 R. .020/0.51 R. .029/0.74 R. .058/1.47 .086/2.18 4 3 .082/2.08 .065/1.65 .094/2.39 "C" "E" "A" "G" 2 1 MATERIAL NUMBER PLATING WIRE SIZE (AWG) 43030-0001 43030-0002 43030-0003 43030-0004 43030-0005 43030-0006 43030-0007 43030-0008 43030-0009 43030-0010 43030-0011 43030-0012 A B C A B C A B C A B C 20-24 20-24 20-24 26-30 26-30 26-30 20-24 20-24 20-24 26-30 26-30 26-30 43030-0038 A 18 OR 0.75mm2 (SEE NOTE 10) CHAIN 43030-0039 B 18 OR 0.75mm2 (SEE NOTE 10) CHAIN 43030-0040 C 18 OR 0.75mm2 (SEE NOTE 10) CHAIN "D" SECTION V-V F .075/1.91 .030/0.76 R. .025/0.64 R. .030/0.76 R. 5 6 "C" "H" G 7 8 "A" .091/2.31 .075/1.91 .091/2.31 .050/1.27 .073/1.85 9 SECTION W-W FORM CHAIN H CHAIN CHAIN CHAIN CHAIN CHAIN LOOSE LOOSE LOOSE LOOSE G LOOSE LOOSE F NOTES .433 REF 11.00 1) MATERIAL: PHOSPHOR BRONZE ALLOY 2) TERMINAL PLATING: "A" - HOT TIN DIP: .000040/0.00102 MIN. OVERALL "B" - .000015/0.00038 MIN. SELECT GOLD E CL E .000100/0.00254 MIN. SELECT TIN CL ALL OVER .000050/0.00127 MIN. NICKEL OVERALL. "C" - .000030/0.00076 MIN. SELECT GOLD .000100/0.00254 MIN. SELECT TIN .044±.002 1.12±0.05 .010 0.25 MAX VESTIGE PLATING FINISHES B AND C ARE POST PLATED. 3) PRODUCT SPECIFICATION: PS-43045, PS-43650, PS-44300-001. D MINIMUM AREA OF SELECT GOLD PLATING 2 PLACES (INSIDE ONLY) (PLATING B AND C ONLY) .138 3.50 .081 2.05 5) TERMINAL FOR USE IN MICRO-FIT RECEPTACLE SERIES 43025, 43645, 44133, AND 46623. ONLY 20-24 AWG AND 26-30 AWG TERMINALS CAN BE USED IN TPA RECEPTACLE SERIES 171850 AND 172952. 6) FOR TERMINAL ORIENTATION IN RECEPTACLE SEE DRAWINGS FOR COINED AREA RECEPTACLES. 7) THIS TERMINAL IS DESIGNED IN METRIC. V W D 4) PACKAGING SPECIFICATION: PK-43030-001 (REEL), PK-43030-003 (LOOSE). .169 4.30 C ALL OVER .000050/0.00127 MIN. NICKEL OVERALL. 8) MOLEX RECOMMENDS THE USE OF MICRO-FIT TEST PLUG (SERIES 44242) C WHENEVER CONTINUITY TESTING IS PERFORMED. TEST PLUGS MUST NOT BE USED TO MAKE OR BREAK UNDER LOAD. MOLEX DOES NOT RECOMMEND USING STANDARD MATING COMPONENTS (SERIES 43020, 43045, 43640, 43650, OR 43031) FOR HARNESS TESTING PURPOSES. V W SELECT TIN AREA (BOTH SIDES) B 9) TEXT ON PART IS FOR REFERENCE ONLY. TEXT AND TEXT LOCATION MAY .053±.003 1.35±0.08 VARY DEPENDING ON PART NUMBER AND/OR TOOL. (SCALE 20:1) 10) 18 AWG PART NUMBERS ARE DESIGNED FOR 18 AWG 1061 STYLE WIRE OR A (PLATING B AND C ONLY) SYMBOLS = 0 = 0 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE IN/MM 10:1 = 0 = 0 A MM ± 3 PLACES ± ± P1 RELEASE DATE 11 2020/03/09 10 EM-43030-ASSY 19:24:30 9 8 7 6 C 0.25 ± 0.014 ± 0.35 ± 1 PLACE = 0 0 PLACES ± = 0 0.01 2 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 INCH 4 PLACES ± = 0 = 0 CURRENT REV DESC: 43030-0040 CORRECT PLATING TO "C" GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 B .073/1.85 MAXIMUM INSULATION OUTSIDE DIAMETER. ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 633510 2020/03/05 2020/03/06 2020/03/09 DRWN: MKIPPER CHK'D: SSOUSEK APPR: FSMITH INITIAL REVISION: DRWN: MUELLER APPR: MARGULIS THIRD ANGLE PROJECTION 4 MICRO-FIT (3.0) FEMALE CRIMP TERMINAL PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2002/08/03 2002/08/03 DRAWING SERIES C-SIZE 43030 3 SD-43030-XXXX MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 N8 SHEET NUMBER 1 OF 1 1 A