0908143622

9 7 8 5 6 4 3 PART NUMBER CARRIER TAPE FOR STANDARD SMT HEADERS. 12.0 PITCH A 9.4 2.00 ±0.15 ⌀ 1.50 +0.10 -0.00 90814-*220/-*520 90814-*218/-*518 90814-*216/-*516 90814-*214/-*514 90814-*212/-*512 90814-*210/-*510 90814-*208/-*508 90814-*206/-*506 90814-*204/-*504 4.0 PITCH SEE NOTE 2 1 E C ±0.10 1.75 E 2 NO. OF PIECES REELS PIECES DIM A DIM B DIM C DIM D DIM E DIM F DIM G CKTS PER BOX PER BOX PER REEL 20 18 16 14 12 44.0 40.4 20.2 29.5 50.4 44.4 100.0 1800 3 600 10 8 6 4 ⌀360.0 MAX. REF A ±0.30 D REF B ±0.10 ⌀ 2.0 MIN CARBOARD BOX ⌀13.0 E MAX .REF REF OUTSIDE ØG REF B D D B F +2.00 -0.00 REF A SECTION A-A DETAIL C INSIDE REEL REEL DIMENSIONS REFERENCE ONLY C C DIRECTION OF UNREELING 1.50 REF SECTION B-B SEE DRAWING NO. SDA-90814 FOR COMPONENT DETAIL COVER TAPE 1.70 REF 0.20 STANDARD SMT PICOFLEX COMPONENT & CAP DETAIL PART NUMBERS 90814-*2**/-*5** R 0.75 B B AREA FOR VACUUM HEAD Ø4.00 REF. TO CUSTOMER ASSEMBLY MACHINE DETAIL C SCALE 10:1 5.6 BLISTER TAPE THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION MOLEX REEL NOTES: 1. MATERIAL: DOCUMENT STATUS 9 P1 RELEASE DATE ± 2. PITCH TOLERANCE OVER ANY 10 PITCHES ±0.2 mm. 4 PLACES ± 3. ALL CAVITY WALLS HAVE DRAFT ANGLE UNLESS STATED OTHERWISE. 3 PLACES ± 4. ALL INTERNAL RADII R0.3 MAX. 2 PLACES ± 8.6 7.3 5. PEEL FORCE OF THE COVER TAPE IS 0.1 N TO 1.3 N AT MAXIMUM PEEL SPEED OF 300 mm/MIN, ±10%. 2018/04/18 8 1.5:1 ANGULAR TOL COVER TAPE: COLD SEAL POLYESTER, 0.06 mm REF. THICK, TRANSPARENT. 6. REFERENCE TO IEC 60286-3. FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 SCALE mm 1 PLACE ± 0 PLACES ± 2.0 ° 0.1 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:52:11 7 6 5 CURRENT REV DESC: REVISED GENERAL TOLERANCES (UNLESS SPECIFIED) CARRIER TAPE: VOLUME NON-CONDUCTIVE ANTISTATIC COATED POLYSTYRENE, 0.4 mm REF. THICK, CLEAR. 2.75 A PICK & PLACE CAP 9.6 DIMENSION UNITS 4 EC NO: 169568 DRWN: BPMURPHY CHK'D: DSHEA APPR: DBYRNES INITIAL REVISION: DRWN: BPMURPHY APPR: DBYRNES THIRD ANGLE PROJECTION 3 2017/12/05 2018/04/13 2018/04/18 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/09/25 2017/11/17 908149002 MATERIAL NUMBER DRAWING SERIES A3-SIZE 90814 2 A PICOFLEX SMT HEADER BLISTER TAPE SEE TABLE PSD 000 B SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 2 9 7 8 5 6 4 3 PART NUMBER CARRIER TAPE FOR LOW PROFILE SMT HEADERS. 12.0 PITCH 1 E C ±0.10 1.75 E 4.0 PITCH SEE NOTE 2 2.0 ±0.15 ⌀ 1.50 +0.10 -0.00 7.8 90814-*720/-*920 90814-*718/-*918 90814-*716/-*916 90814-*714/-*914 90814-*712/-*912 90814-*710/-*910 90814-*708/-*908 90814-*706/-*906 90814-*704/-*904 F 2 NO. OF PIECES REELS PIECES DIM A DIM B DIM C DIM D DIM E DIM F DIM G CKTS PER BOX PER BOX PER REEL 20 18 16 14 12 44.0 40.4 20.2 29.5 50.4 44.4 100.0 1800 3 600 10 8 6 4 ⌀ 2.0 MIN A ±0.30 D REF B ±0.10 ⌀360.0 MAX. REF CARBOARD BOX ⌀13.0 E MAX .REF REF OUTSIDE ØG REF G D D G F +2.00 -0.00 REF F SECTION F-F DETAIL H 1.50 REF INSIDE REEL REEL DIMENSIONS REFERENCE ONLY C C 0.20 REF SECTION G-G SEE DRAWING NO. SDA-90814 FOR COMPONENT DETAIL R 0.75 REF TO CUSTOMER ASSEMBLY MACHINE B 1.70 REF LOW-PROFILE SMT PICOFLEX COMPONENT & CAP DETAIL PART NUMBERS 90814-*7**/-*9** B DETAIL H SCALE 10:1 5.6 AREA FOR VACUUM HEAD Ø4.00 REF. MOLEX REEL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION NOTES: 1. MATERIAL: A 9.6 CARRIER TAPE: VOLUME NON-CONDUCTIVE ANTISTATIC COATED POLYSTYRENE, 0.4 mm REF. THICK, CLEAR. 2.75 PICK & PLACE CAP 7.0 5.8 3. ALL CAVITY WALLS HAVE DRAFT ANGLE UNLESS STATED OTHERWISE. DOCUMENT STATUS 9 P1 RELEASE DATE 2018/04/18 8 SCALE mm 1.5:1 4. ALL INTERNAL RADII R0.3 MAX. ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 5. PEEL FORCE OF THE COVER TAPE IS 0.1 N TO 1.3 N AT MAXIMUM PEEL SPEED OF 300 mm/MIN, ±10%. 1 PLACE ± 6. REFERENCE TO IEC 60286-3. 0 PLACES ± 2.0 ° 0.1 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 13:52:11 7 6 5 CURRENT REV DESC: REVISED GENERAL TOLERANCES (UNLESS SPECIFIED) COVER TAPE: COLD SEAL POLYESTER, 0.06 mm REF. THICK, TRANSPARENT. 2. PITCH TOLERANCE OVER ANY 10 PITCHES ±0.2 mm. FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 DIMENSION UNITS 4 EC NO: 169568 DRWN: BPMURPHY CHK'D: DSHEA APPR: DBYRNES INITIAL REVISION: DRWN: BPMURPHY APPR: DBYRNES THIRD ANGLE PROJECTION 3 2017/12/05 2018/04/13 2018/04/18 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/09/25 2017/11/17 908149002 MATERIAL NUMBER DRAWING SERIES A3-SIZE 90814 2 A PICOFLEX SMT HEADER BLISTER TAPE SEE TABLE PSD 000 B SHEET NUMBER CUSTOMER GENERAL MARKET 1 2 OF 2 13 12 11 10 9 8 7 5 6 4 3 2 1 5 H H 2.10 ±0.10 4 6 1 STANDARD G 3 G PROFILE 2 REFLOW 7 AD NOTE 9 0.0 A -0.2 LOW 8 PROFILE F F REFLOW NOTE 9 CIRCUIT No.1 2.54±0.10 �1.075� 9 MICROMETRE 0.76μm GOLD VERSION 16 10 E E 11 12 15 D D 25 13 14 NOTES: 1) MATERIAL: HOUSING: NYLON (PA) GLASS FILLED. UL94 V-0, NATURAL (BEIGE) C C TERMINAL - CARTRIDGE BRASS 0.28 REF THICK 60 2) PLATING: TIN: TIN (Sn) 3-5 MICROMETRE OVER 1.27 MICROMETRE MIN NICKEL(Ni). GOLD : UNDERPLATED 1.27μm MIN NICKEL 3-5μm TIN SELECTIVE 0.76μm MIN. SELECTIVE GOLD 3) MATES WITH MOLEX 90327 PART SERIES. 4) ALL SMT TAILS TO LIE WITHIN A COPLANARITY BAND OF B B 0.0 - 0.10 REF. FROM EACH OTHER. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 5) FOR TAPE AND REEL PACKAGING SEE 908149001 PSD AND 908149002 PSD. FOR TUBE PACKAGING SEE PK-90814-001 6) PCB PEGS ARE OPTIONAL. mm 5:1 ANGULAR TOL 8) PRODUCT SPECIFICATION: PS-99020-0011 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± INSPECTION NUMBERS USED ON SHEET 1: 1-50 1 PLACE ± LAST INSPECTION NUMBER: 16 0 PLACES ± 9) FOR RECOMMENDED REFLOW PROFILES, REFER TO PS-99020-0011 APPENDIX B DOCUMENT STATUS 13 FORMAT: master-tb-prod-A2 REVISION: H DATE: 2018/01/18 SCALE P1 RELEASE DATE 12 CURRENT REV DESC: TYPO ERROR CORRECTED GENERAL TOLERANCES (UNLESS SPECIFIED) 7) PCB LAYOUT SHOWN ON SHEET 2. A DIMENSION UNITS 2021/01/11 11 0.5 ° 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:22:12 10 9 8 7 6 5 EC NO: 647680 DRWN: SMAHAJANSHET CHK'D: NCSR APPR: NCSR INITIAL REVISION: DRWN: DMCNAMAR APPR: EFOLEN THIRD ANGLE PROJECTION 4 2020/10/23 2020/10/23 2020/10/23 PICOFLEX SMT HEADER PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2001/08/16 2010/11/04 DRAWING SERIES A2-SIZE 90814 3 SDA-90814 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART GENERAL MARKET 2 AE SHEET NUMBER 1 OF 2 1 A 13 12 11 10 9 8 7 5 6 4 3 2 1 H H REF. REF. REF. REF. RESTRICTED AREA NO PCB COMPONENTS ALLOWED REF. REF. G 7.90 7.90 2.54 CIRCUIT 1 2.54 CIRCUIT 1 PITCH F REF. RESTRICTED AREA NO PCB COMPONENTS ALLOWED CIRCUIT 2 REF. REF. REF. CIRCUIT 2 G TYP. REF. REF. TYP. REF. 1.93 PITCH 1.93 REF. F REF. REF. A A RECOMMENDED P.C.B. THICKNESS 1.60±0.14 RECOMMENDED P.C.B. THICKNESS 1.60±0.14 E E D D REF. TYP. REF. 7.90 REF. CIRCUIT 2 REF. RESTRICTED AREA NO PCB COMPONENTS ALLOWED C C CIRCUIT 1 2.54 PITCH A B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 5:1 CURRENT REV DESC: TYPO ERROR CORRECTED GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL A DOCUMENT STATUS 13 FORMAT: master-tb-prod-A2 REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 12 2021/01/11 11 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.1 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:22:12 10 9 8 7 6 5 EC NO: 647680 DRWN: SMAHAJANSHET CHK'D: NCSR APPR: NCSR INITIAL REVISION: DRWN: DMCNAMAR APPR: EFOLEN THIRD ANGLE PROJECTION 4 2020/10/23 2020/10/23 2020/10/23 PICOFLEX SMT HEADER PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2001/08/16 2010/11/04 DRAWING SERIES A2-SIZE 90814 3 SDA-90814 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART GENERAL MARKET 2 AE SHEET NUMBER 2 OF 2 1 A