34905-2447

18 17 16 15 14 13 12 10 11 9 7 8 5 6 4 3 2 1 M M ISO VIEW SCALE 5:1 L I G R I G T L N M K K ⌀H ⌀H ⌀F SECTION R-R VIEW IS ROTATED 90° SECTION T-T VIEW IS ROTATED 90° ⌀F R T SECTION N-N VIEW IS ROTATED 90° CONTACT GEOMETERY 6 J M SECTION M-M VIEW IS ROTATED 90° CONTACT GEOMETERY 1 J �13.10� �13.10� 10.7 2.4 10.7 1.50 ±0.05 1.25 ±0.03 0.95 ±0.05 N 1.25 ±0.03 0.95 ±0.05 5.00 ±0.05 2.4 1.50 ±0.05 5.07 ±0.05 H H 0.98 1.95 ±0.03 1.95 ±0.03 1.15 ±0.05 1.15 ±0.05 0.14 ±0.05 CONTACT GEOMETERY 6 G J J 0.14 CONTACT GEOMETERY 1 G CONTACT GEOMETERY 6 CONTACT GEOMETERY 1 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. MATERIAL: COPPER ALLOY 2. PLATING: SEE TABLE 1 2.1 ANTI-TARNISH TREATMENT FOR SILVER PLATED AREA: SYNTHETIC HYDROCARBON CONTACT SURFACE FINISH OR EQUIVALENT F F 3. PACKAGING SPEC: 313025040 E �1.96� 4. CRIMPING SPEC: AS-34905-001 �1.96� SECTION P-P CONTACT GEOMETERY 6 5. PROBING THE CONTACT INTERFACE OF THE TERMINAL OR AT ANY POINT ON THE TERMINAL BEAM IS NOT PERMITTED P 6. FOR SILVER PLATING: ELECTRICAL PERFORMANCE IS NOT AFFECTED BY TARNISH ON SILVER PLATING SURFACE. ACCEPTABLE SILVER SURFACES CAN INCLUDE TARNISH OF ANY OF THE OBSERVED COLORS. OBSERVED TARNISH COLORS ARE YELLOW, BROWN, GRAY, BLUE, OR BLACK. P D DATE CODE L L D DATE CODE TRADEMARK TRADEMARK MARKING TYPE E SECTION L-L CONTACT GEOMETERY 1 MARKING TYPE CONTACT GEOMETERY 6 C C CONTACT GEOMETERY 1 TABLE 2 PART NUMBER D Wind Part B Wind Part Number Number Top Layer Plating Type Status Contact geometry Marking Wire Insulation Grip Code Type OD - mm Wire Size mm² FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: Dimensions - mm = Dim F Dim G ± 0.20 Dim H Dim I Dim J ± 0.05 = B 34905-6447 34905-6449 Ag SALEABLE 6 34905-2447 34905-2449 SALEABLE Sn 1 L1 34905-6448 34905-6450 IN VALIDATION Ag 6 S2H 34905-2448 34905-2450 IN VALIDATION 1 Sn S2 1.20-1.40 0.95-1.05 0.35 0.13 1.36 0.82 2.35 1.90 0.90 0.68 DOCUMENT STATUS 18 P1 RELEASE DATE 17 16 2021/06/09 GENERAL TOLERANCES (UNLESS SPECIFIED) 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± = 1.88 ± 0.20 0.18 1.30 ± 0.15 0.00 S2 0 1.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 21:29:11 15 15:1 ± A FORMAT: master-tb-prod-A1 REVISION: J DATE: 2020/01/14 0 mm ANGULAR TOL L1H L1 0 14 13 12 11 10 9 8 7 6 EC NO: 666511 DRWN: RMV02 CHK'D: SMAHADIK APPR: BMOSER INITIAL REVISION: DRWN: SJAZRAWI APPR: YLEPOTTIER THIRD ANGLE PROJECTION 5 B CTX50 SEALED RCPT TERM 2021/03/30 2021/06/09 2021/06/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/07/13 2016/08/01 DRAWING SERIES A1-SIZE 34905 4 349050400 MATERIAL NUMBER SEE TABLE 3 PSD 000 CUSTOMER GENERAL MARKET 2 C1 SHEET NUMBER 1 OF 1 1 A