5020781362

9 7 8 5 6 4 REEL 2 1 注記 NOTES 引き出し方向 PULL OUT DIRECTION E 3 E 1. 製品詳細寸法については製品単体図面を参照下さい。 DETAIL DIMENSION, SEE PRODUCT DRAWING 2. 梱包数量：6000 個／リール NUMBER OF CONNECTORS : 6000 PCS/REEL 3. リードテープ長さ LEAD TAPE LENGTH ⌀ 380 ±2 (⌀ 80) 100MIN. 引き出し方向 PULL OUT DIRECTION トップテープ接着部（空エンボス） TOP TAPE BONDED PART. (EMPTY) 部品挿入部 COMPONENT SUPPLIER D 400MIN. "C" D 4. 材料 MATERIAL キャリアテープ (CARRIER TAPE) : ポリスチレン (POLYSTYRENE) トップテープ (TOP TAPE) : PET , PE , PEF リール (REEL) : ポリスチレン (PS) POLYSTYRENE (PS) 5. カバーテープの剥離強度については、 IEC60286-3 に準拠 COVER TAPE PEEL FORCE IS DEFINED BY IEC 60286-3. 2 ±0.5 B ±1.0 末端部 （空部） TAIL PART (EMPTY) 160MIN. C C (⌀ 20) (⌀10) (120°) (2) B B (⌀21) (⌀ 13) CONNECTOR SERIES NO. 502078**68 DETAIL C 2016/11/24 2017/01/27 2017/01/27 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 24.05.2016 8 07:26:32 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 112453 RYANAIDANI KTAKAHASHI MSASAO ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 1:1 DRWN BY DATE RYANAIDANI 2016/11/24 DATE CHK'D BY 2017/01/27 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.25MM PITCH FPC CONN HGT =1.0 HSG ASSY EMBOSSED TAPE PACKAGE A DATE 2017/01/27 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 502078 SEE CHART DOCUMENT NUMBER 3 CUSTOMER GENERAL DOC TYPE DOC PART SHEET NUMBER 5020780001 2 PSD 000 1 1 OF 3 9 7 8 5 6 4 3 2 1 E E (4.14) (2.89) 引き出し方向 PULL OUT DIRECTION (1.8) (0.72) (0.5) 502078**68 Y X X (0.2) 0.3 ±0.05 D D D ±0.3 (A) トップテープ TOP TAPE 8 ±0.1 ⌀ 1.5 +0.1 0 SECTION Y-Y (PITCH) Y 2 ±0.1 4 ±0.1 16,24mm 幅キャリアテープ 16,24mm WIDTH CARRIER TAPE 1.75 ±0.1 エンボステープ EMBOSSED TAPE C SECTION X-X (C) コネクタ CONNECTOR C 累積ピッチ 40±0.2 ACUMLATIVE PITCH 40±0.2 15.3 14.8 13.3 11.8 11.5 25.4 11.3 10.3 8.3 7.3 6.3 7.5 17.4 5.3 24 B 16 5020785362 5020785162 5020784562 5020783962 5020783762 5020783362 5020782562 5020782162 5020781762 5020781362 53 51 45 39 37 33 25 21 17 13 B 極数 オーダー番号 ORDER NO. CIRCUITS CONNECTOR SERIES NO. 502078**68 D キャリアテープ幅 CARRIER TAPE WIDTH C B (A) 2016/11/24 2017/01/27 2017/01/27 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 24.05.2016 8 07:26:32 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 112453 RYANAIDANI KTAKAHASHI MSASAO ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 1:1 DRWN BY DATE RYANAIDANI 2016/11/24 DATE CHK'D BY 2017/01/27 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.25MM PITCH FPC CONN HGT =1.0 HSG ASSY EMBOSSED TAPE PACKAGE A DATE 2017/01/27 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 502078 SEE CHART DOCUMENT NUMBER 3 CUSTOMER GENERAL DOC TYPE DOC PART SHEET NUMBER 5020780001 2 PSD 000 1 2 OF 3 9 7 8 5 6 4 3 2 1 (4.14) E 引き出し方向 PULL OUT DIRECTION (2.89) 1.5 502078**68 (1.8) (0.72) (0.5) X X +0.1 0 (R 0.75) Y (0.2) 0.3 ±0.05 E (0.2) トップテープ TOP TAPE SECTION X-X (C) (A) コネクタ CONNECTOR D 28.4 ±0.1 D エンボステープ EMBOSSED TAPE ⌀ 1.5 +0.1 0 SECTION Y-Y 8 ±0.1 (PITCH) C Y 2 ±0.1 4 ±0.1 1.75 ±0.1 C 累積ピッチ 40±0.2 ACUMLATIVE PITCH 40±0.2 32mm 幅キャリアテープ 32mm WIDTH CARRIER TAPE B B 14.2 33.4 17.3 5020786162 61 極数 オーダー番号 ORDER NO. CIRCUITS CONNECTOR SERIES NO. 502078**68 C B (A) 2016/11/24 2017/01/27 2017/01/27 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 24.05.2016 8 07:26:32 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 112453 RYANAIDANI KTAKAHASHI MSASAO ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM 1:1 DRWN BY DATE RYANAIDANI 2016/11/24 DATE CHK'D BY 2017/01/27 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.25MM PITCH FPC CONN HGT =1.0 HSG ASSY EMBOSSED TAPE PACKAGE A DATE 2017/01/27 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 502078 SEE CHART DOCUMENT NUMBER 3 CUSTOMER GENERAL DOC TYPE DOC PART SHEET NUMBER 5020780001 2 PSD 000 1 3 OF 3 7 8 5 6 2.75 1.05 ±0.2 E アクチュエータ ACTUATOR (吸着エリア) (PICK-UP AREA) A 4 3 �1.85� (FPC挿入深さ) (INSERTION DEPTH OF FPC) �1.45� (偶数接点位置) (EVEN CONTACT POSITION) �2.98� Y C �0.33� �1.0� �0.1� X (D) (E) SECTION Y-Y 0.55 ±0.1 (テール部長さ) DIMENSION OF SOLDER TAIL) 奇数端子 ODD TERMINAL E D C B ±0.1 0.25 ±0.07 0.5 ±0.07 �0.12� X 補強金具 FITTING NAIL ハウジング HOUSING (奇数接点位置) (ODD CONTACT POSITION) 1.0 ±0.15 Y �0.4� �0.25� (FPC挿入高さ) (FPC INSERTION HEIGHT) 5 接点間ピッチ (PITCH OF CONTACTS) 1 1. 使用材料 MATERIALS ハウジング : 液晶ポリマー(UL94V-0 、ベージュ) アクチュエータ : ポリアミド(UL94HB 、黒色) 端子 : リン青銅 補強金具 : リン青銅 HOUSING : LCP (BEIGE) ACTUATOR : PA (BLACK) TERMINAL : PHOSPHOR BRONZE FITTING NAIL : PHOSPHOR BRONZE 2. メッキ仕様 PLATING 端子 TERMINAL 接点部：金メッキ0.1 µm以上 テール部：金メッキ 下地：ニッケルメッキ1.0 µm以上 CONTACT AREA : Gold PLATING 0.1µm MINIMUM TAIL AREA : Gold PLATING UNDER PLATING : Nickel PLATING 1.0µm MINIMUM 金具 FITTING NAIL 表面：スズメッキ 1.0 µm以上 下地：ニッケルメッキ1.0 µm以上 ALL OVER : Tin PLATING 1.0µm MINIMUM UNDER PLATING : Nickel PLATING 1.0µm MINIMUM 3. 端子、補強金具のコプラナリティーは0.1以下とする COPLANALITY OF SOLDER TAILS AND FITTING NAILS : 0.1MAX. 4. 一般公差：± 0.3 GENERAL TOLERANCES: ±0.3 5 アクチュエータの図示箇所にゲート逃げの凹みがつきます （極数により、レイアウトが異なります） THERE ARE DENT SHAPES AT ACTUATOR FOR MOLDING GATE （LAYOUT DIFFER ACCORDING TO CIRCUIT NUMBER） 6. ELV & RoHS 適合品 ELV & RoHS COMPLIANT 7. 塩素系・臭素系難燃剤非使用 CHLORINATED AND BROMINATED FLAME RETARDANTS FREE 偶数端子 EVEN TERMINAL �0.7� D 2 注記 NOTES 0.15 ±0.05 9 16.34 15.5 14.5 �0.1� �0.1� (PITCH) �1.86� 0.52 ±0.1 B 5°� SECTION X-X 13.5 13 11.5 10 9.5 8.5 6.5 5.5 4.5 3.5 E D �1.7� �13 (テール部長さ) (DIMENSION OF SOLDER TAIL) 0.37 ±0.05 (テール部長さ) (DIMENSION OF SOLDER TAIL) 14.34 13.84 12.34 10.84 10.34 9.34 7.34 6.34 5.34 4.34 15 17 5020786162 5020786168 61 12.5 13 15 5020785362 5020785368 53 12 12.5 14.5 5020785162 5020785168 51 B 45 10.5 11 13 5020784562 5020784568 9 9.5 11.5 5020783962 5020783968 39 8.5 9 11 5020783762 5020783768 37 7.5 8 10 5020783362 5020783368 33 5.5 6 8 5020782562 5020782568 25 4.5 5 7 5020782162 5020782168 21 4 3.5 6 5020781762 5020781768 17 5 2.5 3 5020781362 5020781368 13 MATERIAL CIRCUIT B A C ORDER No. No. =N 502078**68 CONNECTOR SERIES No. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A (PITCH) �1.25� DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2017/10/06 9 P1 C ±0.1 RELEASE DATE 2018/01/23 8 09:18:27 7 6 SCALE mm 20:1 GENERAL TOLERANCES (UNLESS SPECIFIED) アクチュエータ開放位置 ACTUATOR OPENING POSITION �0.1� 0.5 ±0.07 DIMENSION UNITS 5 4 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS CURRENT REV DESC: REVISED EC NO: 171125 DRWN: MTAKAHASHI04 CHK'D: KTAKAHASHI APPR: NUKITA INITIAL REVISION: DRWN: RYANAIDANI APPR: MSASAO THIRD ANGLE PROJECTION 3 DRAWING 2018/01/19 2018/01/23 2018/01/23 2016/11/24 2017/01/27 PRODUCT CUSTOMER DRAWING A3-SIZE 502078 2 DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5020781001 MATERIAL NUMBER SERIES A 0.25 PITCH FPC CONN E/O HGT=1.0 BTM CONTACT TYPE SEE CHART PSD 000 B SHEET NUMBER CUSTOMER GENERAL 1 OF 2 1 7 8 3 A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2017/10/06 9 P1 RELEASE DATE 0.57 ±0.05 0.25 ±0.03 (0.2：METAL MASK) (PITCH) E 0.95 ±0.05 (PATTERN WIDTH) (PITCH) 3.3 ±0.5 D 0.5 MIN. (OVERLAP) 0.72 ±0.05 1 補強板 (STIFFENER BOARD) 1.76 ±0.05 0.25 ±0.15 0.5 ±0.03 0.25 +0.04 -0.03 0.5 ±0.02 0.25 ±0.02 2018/01/23 0.25 (PITCH) 0.09 MAX. (NARROW PATTERN WIDTH) (PITCH) 0.4 ±0.05 7 0.67 ±0.1 +0.04 -0.03 (PATTERN WIDTH) �0.08� (PATTERN GAP) 適合するFPC推奨寸法 APPLICABLE FPC RECOMMENDED DIMENSION (端子部仕上がり厚さ：0.2±0.03) (THICKNESS: 0.2±0.03) 09:18:27 0.5 ±0.03 0.25*(N-1) ±0.05 0.5 ±0.02 補強板長さが図面通り確保できない場合は、カバーレイと 補強板のオーバーラップ寸法を 0.5mm 以上としてください WHEN STIFFENER BOARD DIMENSION CAN NOT SECURE AS DRAWING, PLEASE GIVE THE OVERLAP SIZE OF COVER FILM AND STIFFENER BOARD AS 0.5mm MINIMUM 推奨ペースト厚 : 100µm 推奨マスク開口率 : 80% RECOMMEND SCREEN THICKNESS : 100µm RECOMMEND SCREEN OPEN RATIO : 80% FPCパターンのメッキ仕様は 金メッキ： 0.1µm 以上 下地ニッケルメッキ： 2~6µm FPC PATTERN PLATING GOLD PLATING : 0.1µm MINIMUM NICKEL UNDER PLATING : 2~6µm 8 0.25*(N-3) ±0.05 (PATTERN GAP) 0.95 ±0.15 1.05 ±0.15 1.8 MIN. 2.15 ±0.3 (COVER FILM END) 2. 0.25 ±0.07 (MARGIN WIDTH) 1 �0.08� (PLATING LEAD) 注記 NOTES 1 0.25 ±0.05 0.25*(N-1) ±0.03 �0.09� 2 (0.2：METAL MASK) FPC 構成材料例 EXAMPLE OF FPC COMPOSITION MATERIAL B 3 0.25 ±0.03 1 カバーレイ：ポリイミド（25μm） COVER FILM: POLYIMIDE（25μm） 導体部：銅箔（35μm） COPPER FOIL（35μm） 熱硬化接着剤 THERMOSETTING ADHESIVE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド（25μm） BASE FILM: POLYIMIDE（25μm） 熱硬化接着剤 THERMOSETTING ADHESIVE C 補強板：ポリイミド STIFFNER BOARD: POLYIMIDE D (PLATING LEAD) 0.25 ±0.07 (MARGIN WIDTH) 3 E 4 0.25*(N+1) ±0.05 端子部メッキ PLATING 0.2 ±0.03 仕上がり厚さ THICKNESS 5 6 0.15 ±0.05 9 FPC挿入側 4. FPCについて(ABOUT FPC) FPC INSERSION SIDE 抜き方向は、導体側から補強板側を推奨します 参考基板レイアウト 補強板材質は、ポリイミドを推奨します RECOMMENDED PCB 接着剤は熱硬化接着剤を推奨します PATTERN DIMENSIONS (REF.) なお、接着剤の接点部への付着は導通不良の 原因となりますので染み出しがないよう、お願いします。 FPCに規定された定格温度が FPC 単体前提である場合が御座います。 コネクタと組み合わせての実使用に置いて、接着層が劣化するなどの信頼性を満足できないケースを回避するため、 実機での評価/確認をお願い致します。 RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFENER BORAD SIDE RECOMMENDED MATERIAL: STIFFENER BOARD: POLYIMIDE BONDING AGENT: THERMOSETTING AGENT PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON THE CONTACT AREA BECAUSE THE EXTRA ADHESIVE MAY CAUSE THE DEFECT IN ELECTRICAL CONTINUITY. NOTE: WHEN ACTUALLY USING IT WITH CONNECTOR, PLEASE DO THE EVALUATION AND THE CONFIRMATION WITH AN ACTUAL EQUIPMENT TO EVADE THE CASE WHERE RELIABILITY CANNOT BE FILLED (THE ADHESIVE LINE OF FPC IS DETERIORATED ETC,) C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 20:1 GENERAL TOLERANCES (UNLESS SPECIFIED) 6 5 4 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS CURRENT REV DESC: REVISED EC NO: 171125 DRWN: MTAKAHASHI04 CHK'D: KTAKAHASHI APPR: NUKITA INITIAL REVISION: DRWN: RYANAIDANI APPR: MSASAO THIRD ANGLE PROJECTION 3 DRAWING 2018/01/19 2018/01/23 2018/01/23 2016/11/24 2017/01/27 PRODUCT CUSTOMER DRAWING A3-SIZE 502078 2 DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5020781001 MATERIAL NUMBER SERIES A 0.25 PITCH FPC CONN E/O HGT=1.0 BTM CONTACT TYPE SEE SHEET 1 PSD 000 B SHEET NUMBER CUSTOMER GENERAL 2 OF 2 1