5033204160

9 7 8 5 6 4 3 2 1 注記 NOTES: E 1. 製品詳細寸法については図面 5033201000 を参照下さい。 FOR DETAIL OF CONNECTOR DIMENSIONS, SEE 5033201000 2. 梱包数量: 3000 個／リール NUMBER OF CONNECTORS : 3000 PCS/REEL 3. リードテープ長さ LEAD TAPE LENGTH REEL PULL OUT DIRECTION 100 MIN. �⌀ 80� PULL OUT DIRECTION ⌀ 330 ±2 末端部 （空部） トップテープリーダー部 TOP TAPE LEADER PART 400 MIN. D �2� 0°� �⌀ 20� COMPONENT SUPPLIER TAIL PART (EMPTY) 160 MIN. �12 C 部品挿入部 4. 材料 MATERIAL キャリアテープ (CARRIER TAPE) : ポリスチレン (POLYSTYRENE) トップテープ (TOP TAPE) : PET , PE , PEF リール (REEL) : ポリスチレン (PS) リサイクル材を含む POLYSTYRENE (PS) 5. ELV & RoHS COMPLIANT B ±1 C ±1 "C" トップテープ接着部（空エンボス） TOP TAPE BONDED PART. (EMPTY) 引き出し方向 D �⌀ 10� E C �⌀ 21� �⌀ 13� DETAIL "C" B B MATERIAL NO. 503320**60 2015/12/07 2015/12/24 2015/12/24 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) REDRAW RELEASE STATUS FORMAT: tb-prod-A3 REVISION: F DATE: 2015/11/16 9 P1 RELEASE DATE 2015/12/24 8 A 03:08:21 7 6 5 REV EC NO: DRWN: CHK'D: APPR: A 102256 VNANDAM YNOGAWA YNOGAWA ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE mm --- DRWN BY DATE VNANDAM 2015/12/07 DATE CHK'D BY 0.25MM PITCH FPC CONN HGT=1.65 HSG ASSY EMBOSSED TAPE PACKAGE HIIJIMA APPR BY YNOGAWA DRAWING SIZE A DATE 2015/12/24 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503320 SEE CHART DOCUMENT NUMBER GENERAL DOC TYPE DOC PART SHEET NUMBER 5033200000 3 CUSTOMER 2 PSD 1 OF 2 000 1 9 7 8 5 6 E 4 3 2 1 E �3.89� �2.89� �0.72� 503320**68 �2.45� �0.5� 引き出し方向 0.3 PULL OUT DIRECTION X X �1.85� Y D D �D� TOP PLATE E ±0.3 �A� トップテープ エンボステープ ⌀ 1.5 +0.1 0 EMBOSSED TAPE 8 ±0.1 (PITCH) C Y 24mm 幅キャリアテープ 24mm WIDTH CARRIER TAPE 2 4 SECTION X-X 1.75 ±0.1 コネクタ CONNECTOR C 累積ピッチ 40±0.2 ACCUMLATIVE PITCH 40±0.2 B 12.3 11.5 29.4 25.4 11.3 8.3 24 E キャリアテープ幅 CARRIER TAPE WIDTH (D) C 5033204160 41 5033203760 37 B 5033202560 25 EMBOSSED PACKAGE 極数 (A) オーダー番号 ORDER NO. CKT MATERIAL NO. 503320**60 B 2015/12/07 2015/12/24 2015/12/24 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) REDRAW RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 9 P1 RELEASE DATE 2015/12/24 8 03:08:21 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 102256 VNANDAM YNOGAWA YNOGAWA ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE mm --- DRWN BY DATE VNANDAM 2015/12/07 DATE CHK'D BY 0.25MM PITCH FPC CONN HGT=1.65 HSG ASSY EMBOSSED TAPE PACKAGE HIIJIMA APPR BY YNOGAWA DRAWING SIZE A DATE 2015/12/24 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503320 SEE CHART DOCUMENT NUMBER 3 CUSTOMER GENERAL DOC TYPE DOC PART SHEET NUMBER 5033200000 2 PSD 000 1 2 OF 2 9 7 8 0.15 A 5 6 3 偶数端子 EVEN TERMINAL アクチュエータ ACTUATOR �1.85� （FPC 挿入深さ） (INSERTION DEPTH OF FPC) 2.75 E 0.7 C �0.33� X �D� (接点位置） (CONTACT POSITION) 補強金具 FITTING NAIL ハウジング HOUSING �0.1� �0.55� �1.86� 0.52 (テール部長さ) (DIMENSION OF SOLDER TAIL) �E� CL (PITCH) 0.37 E D C SECTION X-X � 5° B ±0.1 0.5 ±0.07 1 (テール部長さ) (DIMENSION OF SOLDER TAIL) (テール部長さ) (DIMENSION OF SOLDER TAIL) � 2� �1.0� 奇数端子 ODD TERMINAL �0.1� 1.65 ±0.15 (FPC 挿入高さ) (FPC INSERTION HEIGHT) X 接点間ピッチ (PITCH OF CONTACTS) D Y �0.25� �0.95� Y CL (接点位置） (CONTACT POSITION) �1.45� �2.98� 2 注記 NOTES: 1. 使用材料 MATERIALS ハウジング : 液晶ポリマー(ガラス充填、UL94V-0 、ベージュ) アクチュエータ : ポリアミド(ガラス充填、UL94HB、黒色) 　奇数端子 : 銅合金 　偶数端子 : 銅合金 　補強金具 : 銅合金 HOUSING : LIQUID CRYSTAL POLYMER (GLASS FILLED, BEIGE) ACTUATOR : POLYAMIDE (GLASS FILLED, BLACK) ODD TERMINAL : COPPER ALLOY EVEN TERMINAL : COPPER ALLOY FITTING NAIL : COPPER ALLOY 2. メッキ仕様 PLATING 端子 TERMINAL テール部：部分金メッキ 接点部：部分金メッキ 0.1µm MIN. 下地：ニッケルメッキ 1.0µm MIN. TAIL AREA : SEPARATED GOLD PLATING CONTACT AREA : SEPARATED GOLD PLATING 0.1µm MIN. UNDER PLATING : NICKEL PLATING 1.0µm MIN. 金具 FITTING NAIL テール部：スズメッキ 0.5µm MIN. 下地：ニッケルメッキ 1.0µm MIN. TAIL AREA : TIN PLATING 0.5µm MIN. UNDER PLATING : NICKEL PLATING 1.0µm MIN. 3. 端子、補強金具のコプラナリティーは0.1以下とする COPLANALITY OF SOLDER TAILS AND FITTING NAILS : 0.1MAX. 4. 一般公差：±0.3 GENERAL TOLERANCES: ±0.3 5. ELV & RoHS COMPLIANT. 1 CL 4 3 �1 0.25 ±0.07 �0.1� 11.34 10.5 9.5 10.0 12.0 5033204160 41 B 10.34 9.5 8.5 9.0 11.0 5033203760 37 7.34 6.5 5.5 6.0 8.0 5033202560 25 EMBOSSED PACKAGE 極数 E D B A C オーダー番号 ORDER NO. CIRCUITS �2.28� �0.12� B CONNECTOR SERIES NO. 503320**68 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2015/12/07 2015/12/24 2015/12/24 アクチュエータ開放位置 ACTUATOR OPENING POSITION GENERAL TOLERANCES (UNLESS SPECIFIED) REDRAW �0.1� (PITCH) �1.25� RELEASE STATUS FORMAT: tb-prod-A3 REVISION: F DATE: 2015/11/16 9 P1 C ±0.1 RELEASE DATE 2015/12/24 8 A 03:08:26 7 6 5 REV 0.5 ±0.07 EC NO: DRWN: CHK'D: APPR: A 102256 VNANDAM YNOGAWA YNOGAWA ANGULAR TOL ± 1.0 ° 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE mm 20:1 DRWN BY DATE VNANDAM 2015/12/07 0.25 PITCH FPC CONN E/O HGT=1.65 BTM CONTACT DATE CHK'D BY HIIJIMA APPR BY YNOGAWA DRAWING SIZE A DATE 2015/12/24 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503320 SEE CHART DOCUMENT NUMBER GENERAL DOC TYPE DOC PART SHEET NUMBER 5033201000 3 CUSTOMER 2 PSD 1 OF 2 000 1 7 8 5 6 4 3 0.25 ±0.05 0.2 ±0.03 �0.08� (PLATING LEAD) (PATTERN GAP) 0.5 ±0.02 0.95 ±0.05 0.72 ±0.05 (0.64±0.01) (METAL MASK) D 0.67 FPC 挿入側 FPC INSERSION SIDE 参考基板レイアウト RECOMMENDED PCB PATTERN DIMENSIONS (REF.) 注記 NOTES: 補強板長さが図面通り確保できない場合は、カバーレイと 補強板のオーバーラップ寸法を 0.5mm 以上としてください WHEN STIFFENER BOARD DIMENSION CAN NOT SECURE AS DRAWING, PLEASE GIVE THE OVERLAP SIZE OF COVER FILM AND STIFFENER BOARD AS 0.5mm MINIMUM 2. 推奨マスク厚 : 100µm 推奨マスク開口率 : 80% RECOMMEND SCREEN THICKNESS : 100µm RECOMMEND SCREEN OPEN RATIO : 80% FPC パターンのメッキ仕様は 3 金メッキ： 0.1µm 以上 下地ニッケルメッキ： 2~6µm FPC PATTERN PLATING GOLD PLATING : 0.1µm MINIMUM NICKEL UNDER PLATING : 2~6µm 1 C 4. FPC について (ABOUT FPC) 抜き方向は、導体側から補強板側を推奨します 補強板材質は、ポリイミドを推奨します 接着剤は熱硬化接着剤を推奨します なお、接着剤の接点部への付着は導通不良の 原因となりますので染み出しがないよう、お願いします RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFENER BORAD SIDE RECOMMENDED MATERIAL: STIFFENER BOARD: POLYIMIDE BONDING AGENT: THERMOSETTING AGENT PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON THE CONTACT AREA BECAUSE THE EXTRA ADHESIVE MAY CAUSE THE DEFECT IN ELECTRICAL CONTINUITY B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2015/12/07 2015/12/24 2015/12/24 導体部：銅箔 (35µm) COPPER FOIL (35µm) 熱硬化接着剤 THERMOSETTING ADHESIVE REDRAW 03:08:26 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: 102256 VNANDAM YNOGAWA YNOGAWA 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド (25µm) BASE FILM: POLYIMIDE(25µm) 熱硬化接着剤 THERMOSETTING ADHESIVE 補強板：ポリイミド STIFFENER BOARD: POLYIMIDE カバーレイ：ポリイミド (25µm) COVER FILM: POLYIMIDE(25µm) 8 0.4 ±0.05 0.25*(N-1)±0.05 (PATTERN GAP) A 9 (0.22±0.01) (METAL MASK) �0.08� GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 1.0 ° 2015/12/24 (PITCH) (PITCH) 適合する FPC 推奨寸法 APPLICABLE FPC RECOMMENDED DIMENSION (端子部仕上がり厚さ： 0.2±0.03) (THICKNESS: 0.2±0.03) RELEASE DATE 0.25 ±0.03 0.5 ±0.05 (PATTERN WIDTH) 0.5 ±0.02 FPC 構成材料例 EXAMPLE OF FPC COMPOSITION MATERIAL P1 (0.22±0.01) (METAL MASK) 3.3 ±0.5 1 (OVERLAP) 0.5 MIN. 1 0.25 ±0.02 C RELEASE STATUS (PITCH) E 0.25 +0.04 -0.03 (NARROW PATTERN WIDTH) FORMAT: master-tb-prod-A3 REVISION: F DATE: 2015/11/16 0.25 ±0.03 0.5 ±0.05 (PATTERN WIDTH) 0.09 MAX. B 0.25*(N-3)±0.05 0.25 +0.04 -0.03 0.95 ±0.15 1.05 ±0.15 1.8 MIN. 2.15 ±0.3 端子部メッキ PLATING �0.09� 3 D (COVER FILM END) 仕上がり厚さ THICKNESS 0.25 ±0.07 (MARGIN WIDTH) 1 1.76 ±0.05 0.25 ±0.15 (PLATING LEAD) E 0.25X(N-1)±0.03 補強板 (STIFFENER BOARD) 0.25 ±0.07 0.57 ±0.05 (0.51±0.01) (METAL MASK) 0.25X(N+1)±0.05 (MARGIN WIDTH) 2 0.15 ±0.05 9 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE mm 20:1 DRWN BY DATE VNANDAM 2015/12/07 0.25 PITCH FPC CONN E/O HGT=1.65 BTM CONTACT DATE CHK'D BY HIIJIMA APPR BY YNOGAWA DRAWING SIZE A DATE 2015/12/24 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503320 SEE CHART DOCUMENT NUMBER 3 CUSTOMER GENERAL DOC TYPE DOC PART SHEET NUMBER 5033201000 2 PSD 000 1 2 OF 2