A2409XT-W2

A_(X)T-W2 Series 0.25W,FIXED INPUT, ISOLATED & UNREGULATED DUAL OUTPUT, SMD DC-DC CONVERTER m ulti-country patent protection RoHS F EATURES Small footprint SMD Package Style No Heat sink Required 1KVDC Isolation Temperature Range: -40°C to +85°C Internal SMD construction No External Component Required Industry Standard Pinout RoHS Compliance PRODUCT PROGRAM Input Part Number A0503(X)T-W2 A0505(X)T-W2 A0509(X)T-W2 A0512(X)T-W2 A0515(X)T-W2 A1205(X)T-W2 A1209(X)T-W2 12 10.8-13.2 5 4.5-5.5 Voltage (VDC) Nominal Range Voltage (VDC) ±3.3 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 24 21.6-26.4 ±9 ±12 ±15 Output Current (mA) Max ±38 ±25 ±14 ±11 ±9 ±25 ±14 ±11 ±9 ±25 ±14 ±11 ±9 Min ±4 ±3 ±2 ±2 ±1 ±3 ±2 ±2 ±1 ±3 ±2 ±2 ±1 62 64 65 67 66 65 64 63 64 61 62 63 65 Efficiency (%, Typ.) APPLICATIONS The A_(X)T-W2 Series are specially designed f or applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) W here the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) W here isolation is necessary between input and output (isolation voltage ≤ 1000VDC); 3) Where the regulation of the output voltage and t he output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. A1212(X)T-W2 A1215(X)T-W2 A2405(X)T-W2 A2409(X)T-W2 A2412(X)T-W2 A2415(X)T-W2 Note: The A_XT-W2 series have no 3,6,8,9 pin. For example A0505XT-W2. ISOLATION SPECIFICATIONS I tem I solation voltage I solation resistance Test Conditions Tested for 1 minute and 1mA max Test at 500VDC Min 1000 1000 Typ. M ax Units VDC MΩ OUTPUT SPECIFICATIONS I tem Test Conditions Min Typ. M ax 0.25 F or Vin change of 1%(3.3V output) For Vin change of 1%(Others output) 10% to 100% load (3.3V output) 10% to 100% load (5V output) Load regulation 10% to 100% load (9V output) 10% to 100% load (12V output) 10% to 100% load (15V output) Output voltage accuracy M ORNSUN Science & Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20- 38601272 Http://www.mornsun-power.com Units W MODEL SELECTION Output power Line regulation A0505(X)T-W2 Rated Power Package Style Output Voltage Input Voltage Product Series ±1.5 ±1.2 15 12.8 8.3 6.8 6.3 20 15 15 15 15 % See tolerance envelope graph 100% full load 20MHz Bandwidth Full load, nominal input(24V input) Full load, nominal input (others input) 50 500 110 0.03 100 %/ °C m Vp-p KHz Temperature drift Output ripple &Noise* Switching frequency * Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. T he copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. A_(X)T-W2 A/1-2008 Page 1 of 2 COMMON SPECIFICATION Item Storage humidity Operating temperature Storage temperature Temp. rise at full load Lead temperature Cooling Case material Short circuit protection* MTBF W eight *Supply voltage must be discontinued at the end of short circuit duration. 3500 1.70 1.5mm from case for 10 seconds -40 -55 15 Test Conditions Min Typ. Max 95 85 125 25 260 Free air convection Plastic(UL94-V0) 1 s K hours g °C Units % APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very sm all, please connect a resistor with proper resistance at the output end in parallel to increase the load. Recommended circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). L L TYPICAL CHARACTERISTICS Vin C +Vo C DC DC 0V -Vo GND L C (Figure 1) It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might Operating Temp.(oC) arise. It’s not recommended to connect any external capacitor in the application field. Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure2). RECOMMENDED REFLOW SOLDERING PROFILE 250 Te m p er at u r e ( o C) 200 150 100 50 0 Time ( s ec . ) 90 Sec Max (>220 o C ) 2 60 o C 1 0 S ec M ax 22 0 C o Vin GND +Vo RE G DC DC 0V -Vo OUTLINE DIMENSIONS & FOOTPRINT DETAILS 4. 2 5 ( 0 .1 6 7 ) First Angle Projection REC OMME NDE D FOO TP RINT To p v iew,gr id :2.5 4m m(0 .1 inch) Vin GND RE G +Vo 0V DC DC RE G 6.50 ( 0 . 25 0 ) 6 .25 (0 . 2 4 0) -Vo 2.54 (0.100) 0.25 (0 .010) A_T-W2 10 9 8 7 6 A_XT-W2 10 12 7 45 (Figure2) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. 15 .24 (0.600) 10.1 6 (0 .400) (0 . 4 41 ) 7 .5 0 ( 0 .2 9 5 ) 11 . 2 0 1.8 12345 1.2 (0.047) 2 .54 0.10 (0.1 00 0.004 ) 6 .76 (0.26 6) 0.60 0.05 (0 .0 24 0.00 2) A 1.85 (0.07 3) 7 .15 (0.28 0) 0.25 (0.010) FOO TPRINT DE TAIL S P in Functio n(T) Fun ction (X T) 1 GND G ND 2 Vin Vin 4 0V 0V 5 -Vo -Vo 7 +Vo + Vo 10 NC NC 3, 6, 8, 9 NC NO P IN NC:No Con nection Note : Unit:mm (inch) P in section:0.60 *0 .2 5m m(0 .024*0 .010 inch) P in section tolerances: 0.10mm( 0 .004inch) G eneral tole ran ces: 0.1 5m m( 0.00 6in ch) 0 .50 (0.02 0) 1.35 (0 .0 53) 5 .00 。 Note: 1. All specifications measured at Ta=25°C, humidity