IB0515XT-1W

IB_(X)T-1W Series 1W,FIXED INPUT, ISOLATED & REGULATED single OUTPUT, SMD DC-DC CONVERTER m ulti-country patent protection RoHS FEATURES ●Small Footprint ●Single Voltage Output ●SMD Package Style ●1KVDC Isolation ●No Heatsink Required ●Continuous Short circuit protection ●Internal SMD construction ●Temperature Range: -40°C to +85°C ●Industry Standard Pinout ●No External Component Required ●RoHS Compliance PRODUCT PROGRAM Input Part Number I B0505(X)T-W75 I B0512(X)T-1W I B0515(X)T-1W I B1205(X)T-W75 I B1212(X)T-1W I B1215(X)T-1W 12 11.4-12.6 5 4.75-5.25 Voltage (VDC) Nominal Range Voltage (VDC) 5 12 15 5 12 15 Output Current (mA) Max 150 83 67 150 83 67 Min 15 9 7 15 9 7 68 69 69 68 69 70 Efficiency (%, Typ.) APPLICATIONS The IB_(X)T-1W Series are specially designed for applications wh ere a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) W here the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) Where isolation is necessary between input and output (isolation voltage ≤1000VDC); 3) W here the regulation of the output voltage and the output ripple noise are not demanding. Note: 1. IB_XT-1W series designing; 2. IB_XT-1W series have no 3,6,8,9pin,for example IB0505XT-W75. OUTPUT SPECIFICATIONS Item Output power Line regulation Load regulation Output voltage accuracy For Vin change of ± 5% 10% to 100% load 100% full load 100% full load 20MHz Bandwidth 20MHz Bandwidth Full load, nominal input 10 50 100 Test Conditions Min 0.1 Typ. Max 1 ±0.25 ±1 ±3 0.03 20 100 KHz %/°C m Vp-p % Units W MODEL SELECTION IB0512(X)T-1W R ated P o wer P a ckage Style O u t put V oltage I np u t Vo ltage P ro d uc t Ser ies Temperature drift ripple* Noise* Switching frequency *Test ripple and noise by “ parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. ISOLATION SPECIFICATIONS Item MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20- 38601272 Http://www.mornsun-power.com Test Conditions Tested for 1 minute and 1mA max Test at 500VDC Min 1000 1000 Typ. Max Units VDC MΩ Isolation voltage Isolation resistance Note: 1. All specifications measured at TA=25°C, humidity220 oC) 2 6 0o C 10 S ec M ax 220o C o Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! I f the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against 12345 1.00 (0.039) FOOTPRINT DETAILS Pin 1 2 4 A 7 5 、10 Others F unc tion(T) Func tion(XT ) GND Vin 0V +Vo NC NC GND Vin 0V +Vo NC No Pin OUTLINE DIMENSIONS & FOOTPRINT DETAILS 15.24 (0.600) 10.16 (0.400) 11 . 20 ( . 4 4 1 ) First Angle Projection RECOMMENDED FOOTPRINT Top view, grid: 2.54*2. 54mm(0.1 *0.1inc h) 7 . 50 (0. 2 9 5 ) Top View IB_ T- 1W IB_XT-1 W 2.54 0.10 (0.100 0.004) 0.60 0.05 (0.024 0.002) 2.00 (0.079) 10 9 8 76 10 12 7 45 over-current. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. When the environment temperature is higher than 71°C, the product output power should be less then 60% of the rated power. No parallel connection or plug and play. 6 .5 0 ( 0 .2 5 6 ) 6. 25 ( 0 .2 4 6 ) Side View 0.25 (0.100) 6.76 (0.266) 1.85 (0.073) 7.15 (0.28) 0.30 (0.012) 4 .2 5 ( 0 . 16 7 ) NC:No connection Note: Unit:mm(inch) Pin section:0.60*0.25mm(0.024*0.010inch) Pin tolerances: 0.10mm( 0.004inch) General tolerances: 0.15mm( 0.006inch) 0.50 (0.020) A 1.35 (0.053) 。 5.00 MORNSUN reserves the copyright Specifications subject to change without notice. IB_(X)T-1W A/1-2008 Page 2 of 2