54LS138

1-OF-8 DECODER/ DEMULTIPLEXER The LSTTL / MSI SN54 / 74LS138 is a high speed 1-of-8 Decoder / Demultiplexer. This device is ideally suited for high speed bipolar memory chip select address decoding. The multiple input enables allow parallel expansion to a 1-of-24 decoder using just three LS138 devices or to a 1-of-32 decoder using four LS138s and one inverter. The LS138 is fabricated with the Schottky barrier diode process for high speed and is completely compatible with all Motorola TTL families. SN54/74LS138 1-OF-8 DECODER/ DEMULTIPLEXER LOW POWER SCHOTTKY • • • • • Demultiplexing Capability Multiple Input Enable for Easy Expansion Typical Power Dissipation of 32 mW Active Low Mutually Exclusive Outputs Input Clamp Diodes Limit High Speed Termination Effects CONNECTION DIAGRAM DIP (TOP VIEW) VCC 16 O0 15 O1 14 O2 13 O3 12 O4 11 O5 10 O6 9 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. 16 1 J SUFFIX CERAMIC CASE 620-09 16 1 N SUFFIX PLASTIC CASE 648-08 1 A0 2 A1 3 A2 4 E1 5 E2 6 E3 7 O7 8 GND PIN NAMES A0 – A2 E1, E2 E3 O0 – O7 Address Inputs Enable (Active LOW) Inputs Enable (Active HIGH) Input Active LOW Outputs (Note b) LOADING (Note a) HIGH 0.5 U.L. 0.5 U.L. 0.5 U.L. 10 U.L. LOW 0.25 U.L. 0.25 U.L. 0.25 U.L. 5 (2.5) U.L. 16 1 D SUFFIX SOIC CASE 751B-03 ORDERING INFORMATION SN54LSXXXJ SN74LSXXXN SN74LSXXXD Ceramic Plastic SOIC NOTES: a) 1 TTL Unit Load (U.L.) = 40 µA HIGH/1.6 mA LOW. b) The Output LOW drive factor is 2.5 U.L. for Military (54) and 5 U.L. for Commercial (74) Temperature Ranges. LOGIC DIAGRAM A2 3 2 A1 1 A0 4 E1 E2 E3 5 6 LOGIC SYMBOL VCC = PIN 16 GND = PIN 8 = PIN NUMBERS 123 456 12 3 A0 A1 A2 E O0 O1 O2 O3 O4 O5 O6 O7 15 14 13 12 11 10 9 VCC = PIN 16 GND = PIN 8 7 9 10 11 12 13 14 15 7 O7 O6 O5 O4 O3 O2 O1 O0 FAST AND LS TTL DATA 5-230 SN54/74LS138 FUNCTIONAL DESCRIPTION The LS138 is a high speed 1-of-8 Decoder/Demultiplexer fabricated with the low power Schottky barrier diode process. The decoder accepts three binary weighted inputs (A0, A1, A2) and when enabled provides eight mutually exclusive active LOW Outputs (O0 – O7). The LS138 features three Enable inputs, two active LOW (E1, E2) and one active HIGH (E3). All outputs will be HIGH unless E1 and E2 are LOW and E3 is HIGH. This multiple enable function allows easy parallel expansion of the device to a 1-of-32 (5 lines to 32 lines) decoder with just four LS138s and one inverter. (See Figure a.) The LS138 can be used as an 8-output demultiplexer by using one of the active LOW Enable inputs as the data input and the other Enable inputs as strobes. The Enable inputs which are not used must be permanently tied to their appropriate active HIGH or active LOW state. TRUTH TABLE INPUTS E1 H X X L L L L L L L L E2 X H X L L L L L L L L E3 X X L H H H H H H H H A0 X X X L H L H L H L H A1 X X X L L H H L L H H A2 X X X L L L L H H H H O0 H H H L H H H H H H H O1 H H H H L H H H H H H O2 H H H H H L H H H H H OUTPUTS O3 H H H H H H L H H H H O4 H H H H H H H L H H H O5 H H H H H H H H L H H O6 H H H H H H H H H L H O7 H H H H H H H H H H L H = HIGH Voltage Level L = LOW Voltage Level X = Don’t Care A0 A1 A2 LS04 A3 A4 H 123 A0 A1 A2 E A0 A1 A2 123 E A0 A1 A2 123 E A0 A1 A2 123 E LS138 O0 O1 O2 O3 O4 O5 O6 O7 LS138 O0 O1 O2 O3 O4 O5 O6 O7 LS138 O0 O1 O2 O3 O4 O5 O6 O7 LS138 O0 O1 O2 O3 O4 O5 O6 O7 O0 O31 Figure a FAST AND LS TTL DATA 5-231 SN54/74LS138 GUARANTEED OPERATING RANGES Symbol VCC TA IOH IOL Supply Voltage Operating Ambient Temperature Range Output Current — High Output Current — Low Parameter 54 74 54 74 54, 74 54 74 Min 4.5 4.75 – 55 0 Typ 5.0 5.0 25 25 Max 5.5 5.25 125 70 – 0.4 4.0 8.0 Unit V °C mA mA DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 54 74 54, 74 VOL Output LOW Voltage 74 Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current – 20 0.35 0.5 20 0.1 – 0.4 –100 10 V µA mA mA mA mA 2.5 2.7 54 74 – 0.65 3.5 3.5 0.25 0.4 Min 2.0 0.7 0.8 – 1.5 V V V V Typ Max Unit V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = – 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table IIH IIL IOS ICC VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25°C) Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Address to Output Propagation Delay Address to Output Propagation Delay E1 or E2 Enable to Output Propagation Delay E3 Enable to Output Levels of Delay 2 2 3 3 2 2 3 3 Limits Min Typ 13 27 18 26 12 21 17 25 Max 20 41 27 39 18 32 26 38 Unit ns ns ns ns Test Conditions VCC = 5.0 V CL = 15 pF AC WAVEFORMS V IN 1.3 V 1.3 V V IN 1.3 V 1.3 V t PHL V OUT t PLH t PHL V OUT t PLH 1.3 V 1.3 V 1.3 V 1.3 V Figure 1 Figure 2 FAST AND LS TTL DATA 5-232 -A- Case 751B-03 D Suffix 16-Pin Plastic SO-16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. 751B 01 IS OBSOLETE, NEW STANDARD 751B 03. 16 9 -B1 8 P 8 PL 0.25 (0.010) M B M R X 45° G -TD 16 PL 0.25 (0.010) M C SEATING PLANE K T B S M F J A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 3.80 1.35 0.35 0.40 10.00 4.00 1.75 0.49 1.25 INCHES MIN MAX 0.386 0.150 0.054 0.014 0.016 0.393 0.157 0.068 0.019 0.049 1.27 BSC 0.19 0.10 0 0.25 0.25 7 0.050 BSC 0.008 0.004 0 0.009 0.009 7 ° ° ° ° 5.80 0.25 6.20 0.50 0.229 0.010 0.244 0.019 Case 648-08 N Suffix 16-Pin Plastic -A16 9 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: INCH. DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B" DOES NOT INCLUDE MOLD FLASH. 5. 6. ROUNDED CORNERS OPTIONAL. 648 01 THRU 07 OBSOLETE, NEW STANDARD 648 08. B 1 8 F S C -TK SEATING PLANE L H G D 16 PL 0.25 (0.010) M J M T A M DIM A B C D F G H J K L M S MILLIMETERS MIN MAX 18.80 6.35 3.69 0.39 1.02 19.55 6.85 4.44 0.53 1.77 INCHES MIN MAX 0.740 0.250 0.145 0.015 0.040 0.770 0.270 0.175 0.021 0.070 2.54 BSC 1.27 BSC 0.21 2.80 7.50 0 0.38 3.30 7.74 10 0.100 BSC 0.050 BSC 0.008 0.110 0.295 0 0.015 0.130 0.305 10 ° ° ° ° 0.51 1.01 0.020 0.040 -A16 9 Case 620-09 J Suffix 16-Pin Ceramic Dual In-Line NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -B1 8 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. C L 5. 620 01 THRU 08 OBSOLETE, NEW STANDARD 620 09. -TSEATING PLANE K E F D 16 PL 0.25 (0.010) M N G T A S M J 16 PL 0.25 (0.010) M T B S DIM A B C D E F G J K L M N MILLIMETERS MIN MAX 19.05 6.10 19.55 7.36 4.19 0.39 0.53 INCHES MIN MAX 0.750 0.240 0.770 0.290 0.165 0.015 0.021 1.27 BSC 1.40 1.77 0.050 BSC 0.055 0.070 2.54 BSC 0.23 0.27 5.08 7.62 BSC 0 0.100 BSC 0.009 0.011 0.200 0.300 BSC 0 ° 15 ° ° 15 ° 0.39 0.88 0.015 0.035 FAST AND LS TTL DATA 5-233 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. ◊ FAST AND LS TTL DATA 5-234