SN74LS137D

SN54/74LS137 3-LINE TO 8-LINE DECODERS/DEMULTIPLEXERS WITH ADDRESS LATCHES 3-LINE TO 8-LINE DECODERS/ DEMULTIPLEXERS WITH ADDRESS LATCHES DATA OUTPUTS VCC 16 Y0 15 Y0 A B C GL G2 G1 Y1 14 Y1 Y2 13 Y2 Y3 12 Y3 Y4 11 Y4 Y5 10 Y5 Y6 Y7 16 1 LOW POWER SCHOTTKY Y6 9 J SUFFIX CERAMIC CASE 620-09 1 A 2 B SELECT 3 C 4 GL 5 G2 ENABLE 6 G1 7 8 Y7 GND OUTPUT 16 1 N SUFFIX PLASTIC CASE 648-08 16 1 D SUFFIX SOIC CASE 751B-03 ORDERING INFORMATION SN54LSXXXJ SN74LSXXXN SN74LSXXXD Ceramic Plastic SOIC GUARANTEED OPERATING RANGES Symbol VCC TA IOH IOL Supply Voltage Operating Ambient Temperature Range Output Current — High Output Current — Low Parameter 54 74 54 74 54, 74 54 74 Min 4.5 4.75 – 55 0 Typ 5.0 5.0 25 25 Max 5.5 5.25 125 70 – 0.4 4.0 8.0 Unit V °C mA mA FAST AND LS TTL DATA 5-225 SN54/74LS137 FUNCTION TABLE INPUTS OUTPUTS ENABLE GL X X L L L L L L L L H G1 X L H H H H H H H H H G2 H X L L L L L L L L L C X X L L L L H H H H X SELECT B X X L L H H L L H H X A X X L H L H L H L H X Y0 H H L H H H H H H H Y1 H H H L H H H H H H Y2 H H H H L H H H H H Y3 H H H H H L H H H H Y4 H H H H H H L H H H Y5 H H H H H H H L H H Y6 H H H H H H H H L H Y7 H H H H H H H H H L Output corresponding to stored address, L; all others, H H = high level, L = low level, X = irrelevant (1) A (15) Y0 (14) Y1 (13) SELECT INPUTS (2) B (12) Y3 DATA (11) (3) C (10) Y5 Y4 OUTPUTS Y2 (9) (4) GL (7) (5) G2 (6) G1 Y7 Y6 ENABLE INPUTS FAST AND LS TTL DATA 5-226 SN54/74LS137 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 54 74 54, 74 VOL Output LOW Voltage 74 Input HIGH Current Input LOW Current Short Circuit Current (Note 1) Power Supply Current – 20 0.35 0.5 20 0.1 – 0.4 –100 18 V µA mA mA mA mA 2.5 2.7 54 74 – 0.65 3.5 3.5 0.25 0.4 Min 2.0 0.7 0.8 – 1.5 V V V V Typ Max Unit V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = – 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table IIH IIL IOS ICC VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (VCC = 5.0 V, TA = 25°C) Symbol tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL Parameter Propagation Delay Time, A, B, C to Y Propagation Delay Time, A, B, C to Y Propagation Delay Time, Enable G2 to Y Propagation Delay Time, Enable G1 to Y Propagation Delay Time, Enable GL to Y Levels of Delay 2 4 3 3 2 2 3 3 3 4 Limits Min Typ 11 25 16 19 13 16 14 18 18 25 Max 17 38 24 29 21 27 21 27 27 38 Unit ns ns ns ns ns VCC = 5.0 V CL = 15 pF Test Conditions AC SETUP REQUIREMENTS (TA = 25°C, VCC = 5.0 V) Limits Symbol tW ts th Parameter Pulse Width — Enable at GL Setup Time, A, B, C Hold Time, A, B, C Min 15 10 10 Typ Max Unit ns ns ns VCC = 5.0 V Test Conditions FAST AND LS TTL DATA 5-227 -A- Case 751B-03 D Suffix 16-Pin Plastic SO-16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. 751B 01 IS OBSOLETE, NEW STANDARD 751B 03. 16 9 -B1 8 P 8 PL 0.25 (0.010) M B M R X 45° G -TD 16 PL 0.25 (0.010) M C SEATING PLANE K T B S M F J A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 3.80 1.35 0.35 0.40 10.00 4.00 1.75 0.49 1.25 INCHES MIN MAX 0.386 0.150 0.054 0.014 0.016 0.393 0.157 0.068 0.019 0.049 1.27 BSC 0.19 0.10 0 0.25 0.25 7 0.050 BSC 0.008 0.004 0 0.009 0.009 7 ° ° ° ° 5.80 0.25 6.20 0.50 0.229 0.010 0.244 0.019 Case 648-08 N Suffix 16-Pin Plastic -A16 9 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: INCH. DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B" DOES NOT INCLUDE MOLD FLASH. 5. 6. ROUNDED CORNERS OPTIONAL. 648 01 THRU 07 OBSOLETE, NEW STANDARD 648 08. B 1 8 F S C -TK SEATING PLANE L H G D 16 PL 0.25 (0.010) M J M T A M DIM A B C D F G H J K L M S MILLIMETERS MIN MAX 18.80 6.35 3.69 0.39 1.02 19.55 6.85 4.44 0.53 1.77 INCHES MIN MAX 0.740 0.250 0.145 0.015 0.040 0.770 0.270 0.175 0.021 0.070 2.54 BSC 1.27 BSC 0.21 2.80 7.50 0 0.38 3.30 7.74 10 0.100 BSC 0.050 BSC 0.008 0.110 0.295 0 0.015 0.130 0.305 10 ° ° ° ° 0.51 1.01 0.020 0.040 -A16 9 Case 620-09 J Suffix 16-Pin Ceramic Dual In-Line NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -B1 8 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. C L 5. 620 01 THRU 08 OBSOLETE, NEW STANDARD 620 09. -TSEATING PLANE K E F D 16 PL 0.25 (0.010) M N G T A S M J 16 PL 0.25 (0.010) M T B S DIM A B C D E F G J K L M N MILLIMETERS MIN MAX 19.05 6.10 19.55 7.36 4.19 0.39 0.53 INCHES MIN MAX 0.750 0.240 0.770 0.290 0.165 0.015 0.021 1.27 BSC 1.40 1.77 0.050 BSC 0.055 0.070 2.54 BSC 0.23 0.27 5.08 7.62 BSC 0 0.100 BSC 0.009 0.011 0.200 0.300 BSC 0 ° 15 ° ° 15 ° 0.39 0.88 0.015 0.035 FAST AND LS TTL DATA 5-228 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. ◊ FAST AND LS TTL DATA 5-229